Hello everybodies,
I just upgrade ROM on my kaiser htc, now it's doesn't work, it's boot indefinetly...
Someone can help me plz, thx in advance
Does it start loading the OS? Or is it on the tri-color bootloader screen.
Try enter the bootloader (camera button pressed + reset) and load the ROM again.
Try a hard reset first, if you haven't. I did something at some point that caused that to happen and a hard reset straightened it all out.
Listen to your heart....
I'll try to load it again vcespon and inform you...
It requires blood, prick your finger and feed the tilt.
Try the hard reset or see if you can put it into bootloader mode (power button + camera button + reset). Connect via active sync and see if you get USB and can reflash (or flash a different ROM).
Related
Flashed DID diamond+sprint rom and my phone is stuck in the Touchdiamond screen when it vibrateds first can anyone help me..
tried a Hard Reset?
(hold down center button and volume down while pressing reset for 3 secs)
Yeah thats the first thing i did..no luck just goes back to the start screen.
can u get to Bootloader?
Not sure how to get there..
umm.. Volume key up and reset i think (if not check Wiki)
once in Bootloader you can connect to PC and try flashing ROM again
if this doesnt work, try flashing original ROM (same process) and try a different version of Hard SPL. have u flashed other ROMS ok before?
It use to go in bootloader shen i pushed volume dwn, power button and enter botton..not doing it now..
its Volume Down and reset - my bad
Got to chip off now, good luck with it PM me and i'll see it tomrrow if u still got problems
No luck i have tried everything stuck in this loop anyone have anyother sugjestions
I can get it to go to the hard reset screen but that itanyonter way to force it into bootloader the direction in the manuel are different from what wiki says..
So is it bricked?
Help, help!!!! (
Certainly when upgrade from WM03 to WM06, we all must go to the boot loader option to clean registry, disable KITL, clean storage...etc . However,poor me, I have an XDAII with broken record and camera button, so that I can not get in Boot Loader ( Press ResetButton and hold down CameraButton + RecordButton )
So could any one solve this problem?
many thank!!!!
As this is a mechanical problem, - you can't press buttons, which are physically not there -, there is no software solution!
A little workaround might be possible, but untested yet:
As it is not necessarily so, that you have to do a hard reset to end upgrading,
you can try to skip it, in case the last thing you did in WM2k3(SE) was a hardreset.
There should no difference to a fresh upgraded system, which had done a hr afterwards, but it's untested!!!
To do a hard reset on a running WM5 or WM6.X system, you can try to downgrade, hardreset WM2k3(SE) (As I remember this OS does use this buttons to hr) and then upgrade again. It looks wierd, but might work.
For cookers only:
I suggest to use: http://forum.xda-developers.com/showthread.php?t=510805,
as it's a WWE rom without camera-function for cooking.
Delete everything that belongs to the camera to get a little bit more sectors to fill with apps and proggis you need.
Thank so much for your helping, your guiding is quite clear and detailed but....it's not work surely. The way to get in boot loader depend on model of Xda, not depend on the version of rom. The Himalaya use fomular "Reset +Camera + Button" permanent whatever u use any wmXX
Well, I use Powerbutton -DPad -Reset to enter bootloader. No use of Camera button there.
In WM2k3(SE) the hard reset is powerbutton and reset, as I remember, please correct me, if I´m wrong.
Still no use of the missing button.
Enter bootloader and flash, then try to skip hard reset. Although it is better it is not needed.
To do a hard reset on a running WM5/6.X system use the tool of post#18 here:
http://forum.xda-developers.com/showthread.php?t=351811&page=2
Change options to allow hardreset, tap on left upmost icon twice, tap and hold hardreset and run selected.
Voila, no button needed!!!
Tap the icon left of the '?' and enter anything you want. Congratulations.
My diamond freezes on the startupscreen where you see in the lower left conrner the R, G and D versions in RED.
Can this be fixed?
Yeah I am rite now having the same problem anyone has any suggestions the soft-reset button doesn't work and it is not recognizing my network provider... anyone has any suggestions....
hard reset also doesnt work :-(
Yea since the soft reset button doesn't work I am not sure wht to do it is just stuck up on the startup screen can anyone give any suggestions please.....
if i only could acces the internal storage, put a rom on it, and do a flash with hard reset buttons, then it could be back 2 live but now
Can you get it into bootloader? {Hold Vol. down button while pressing power}
If it will go into bootloader, you can flash from there.
It worked
1. i've put it in bootloader [Hold Vol. down button while pressing power]
2. connected the diamond to my pc with USB-cable
3. Install the original rom
Thx supersanj
Hi all,
so i did a bad flash and my diamond doesnt boot into windows, not a problem with the Unlocker Right? turn off and turn on holding power+down volume key+ center key and back key, it boots into bootloader but it just sits there saying LOADING... and this is because the internal memory wasnt being recognize by windows before the bad flash.
do i have any other alternative??
Hi, fear not my friend. Just boot into bootloader mode by pressing power key and volume down at the same time (If you press the center button also you will trigger a hard reset.) Then plug your phone on your PC. On the bottom of the phone screen you should see that the word serial changes for USB. Then just lauch any rom upgrade(either a stock rom or a custom one). The rom upgrade utility will the upgrade your phone like it normaly does when it's not bricked. It will just be a little longer.
you have hold the power volume down and press soft reset to enter boot loader
Hi
I have the same problem, I flashed my diamond with a bad flash, now it turns over, I try a hard reset, it works not so.
when I plug in the charger, the LED does not light.
what should I do, help me pls!
Here is the link where I downloaded the flash: ftp://ppcgeeks.com/Diamond/Users/Tobeychris/Tutorial/Diamond Unlocker.rar
Dear friends,
I was trying to flash my diamond with mtty, where i guess i messed up with commands, I formatted it, then tried to restart with "task 8" then my phone turned off and never on again no matter what i did or key pushed.
Any help will be much appreciated...
me too
but i don't know how to use Jtag recover BL for Diamond
Update ROM by using the BootLoader
Hello there,
even though you can't boot into your OS in the Diamond, there's a way to enter "BootLoader" mode. I'm not sure it works, but you can give it a try.
Here's how:
- Connect the Diamond to your PC
- Enter bootloader mode on your Diamond: with the device turned on, press and hold the volume down button along with the power button, then press the reset button with the stylus tip, then release the volume down and power buttons when bootloader tricolour screen appears.
- Use the ROM Update Utility. If the previous step worked and your connection is working, then with some luck you will be able to Flash the Device with the ROM update utility.
I've tried to find the thread that discussed this with pictures and such but couldn't. You might want to look for similar instructions
Good luck
Shane
JTAG
does anyone managed to JTAG diamond?