Database Develop

USB NOT WORKING

OK i did a search but did not find anything really related..
a friend of mine at work here just handed me his 8125 after "attempting" to flash his ROM. Not sure what the heck he did BUT
1) the usb is not recognized so not active sync.
3) 3 battery meter only shows a plug (lower right ) yet the battery works.
the phone does recognice the charger..
HELP !!!
thanks in advance !

Reset, enter bootloader, reflash

how do you enter boatloader .. ?
what other 2 buttons with the soft reset button ?

DUlrich1227 said:
how do you enter boatloader .. ?
what other 2 buttons with the soft reset button ?
Click to expand...
Click to collapse
Camera Button is the only one you need to hold when resetting...

i apologize but i must be missing something..
i reset (soft reset and camera button) get cingular screen
starts to boot up and goes to today screen where it does not recognize usb..
is there something else i am to do ?

DUlrich1227 said:
i apologize but i must be missing something..
i reset (soft reset and camera button) get cingular screen
starts to boot up and goes to today screen where it does not recognize usb..
is there something else i am to do ?
Click to expand...
Click to collapse
Press the reset (or power down your device by holding the power button until you get the Okay to turn-off warning).
HOLD the camera button as your device powers up. This will get the BootLoader

just woke up and read your reply thanks ..
this is what i ended up doing
i bluetoothed from one of the roms enterbootloader.exe was able to run it
than ran one of the earlier rom upgrades..
re running the lockiwizb and will install sumters rom2
one question if you read this .. on both of the phones 8125's i get an error at the end of the bat file when running the lockiwiz.. is this normal ? is it because it was already ran once ? i am running it from the root (C

HElp!!!!

Flashed DID diamond+sprint rom and my phone is stuck in the Touchdiamond screen when it vibrateds first can anyone help me..

tried a Hard Reset?
(hold down center button and volume down while pressing reset for 3 secs)

Yeah thats the first thing i did..no luck just goes back to the start screen.

can u get to Bootloader?

Not sure how to get there..

umm.. Volume key up and reset i think (if not check Wiki)
once in Bootloader you can connect to PC and try flashing ROM again
if this doesnt work, try flashing original ROM (same process) and try a different version of Hard SPL. have u flashed other ROMS ok before?

It use to go in bootloader shen i pushed volume dwn, power button and enter botton..not doing it now..

its Volume Down and reset - my bad
Got to chip off now, good luck with it PM me and i'll see it tomrrow if u still got problems

No luck i have tried everything stuck in this loop anyone have anyother sugjestions

I can get it to go to the hard reset screen but that itanyonter way to force it into bootloader the direction in the manuel are different from what wiki says..

So is it bricked?

very urgent, am desperate

is there a way to enter boot loader and gets the 3 color screen without using the volume key, by using the keyboard instead???
my x1 has no rom so it cant be turned on and the volume key is dead.
how can i flash a Rom??????????

darkylight said:
is there a way to enter boot loader and gets the 3 color screen without using the volume key, by using the keyboard instead???
my x1 has no rom so it cant be turned on and the volume key is dead.
how can i flash a Rom??????????
Click to expand...
Click to collapse
Having no ROM installed (i.e. via Task29) does not mean the vol key method won't work. It should work - remove battery, replace battery, hold power and vol key together for a few seconds. The only reason it wouldn't is if there was something physically wrong with the key.

Jezza0 said:
Having no ROM installed (i.e. via Task29) does not mean the vol key method won't work. It should work - remove battery, replace battery, hold power and vol key together for a few seconds. The only reason it wouldn't is if there was something physically wrong with the key.
Click to expand...
Click to collapse
yup via task 29, mtty. i think there is a wrong in the volume key coz its not working any more.
is there a way to boot via keyboard or my x1 is dead?

are you sure
all you have to do is hold the vol DOWN and power until screen comes up

darkylight said:
is there a way to enter boot loader and gets the 3 color screen without using the volume key, by using the keyboard instead???
my x1 has no rom so it cant be turned on and the volume key is dead.
how can i flash a Rom??????????
Click to expand...
Click to collapse
had the same issue mate....and now my x1 is bricked!...couldn't do anything to get it back into tri-colour screen and sent it back to repair...tried to use the usb, mitty and nothing....good luck if you find another method....i hate task29 now i wouldn't try that thing again on my new phone...i did everything correctly and it just completely died on me...

has your volume key always been dead

yea, me 2, my volume key dead
so i cant do task29 before flash a new rom
i search a long time
but cant find solutions
had to send it back to repair the hardware problem

Hi
Try this this i tried might be work for you too...
Put image file in root now run Task29 and as soon as the tri colour screen comes remove the usb cable and wait for 2 minutes it will search for serial and will automatically boot from SD image..
Thanx

darkylight said:
is there a way to enter boot loader and gets the 3 color screen without using the volume key, by using the keyboard instead???
my x1 has no rom so it cant be turned on and the volume key is dead.
how can i flash a Rom??????????
Click to expand...
Click to collapse
What do you get when you just turn on your phone? You can always turn on your phone, if you have a ROM flashed it will boot the ROM. If not or not properly flashed then it will take you to the bootloader....

Lokatho said:
What do you get when you just turn on your phone? You can always turn on your phone, if you have a ROM flashed it will boot the ROM. If not or not properly flashed then it will take you to the bootloader....
Click to expand...
Click to collapse
how could your phone auto loading bootloader without a rom and volume down key press?
is your phone made from E.T ? he can do it auto intelligently
dont bull**** before u r clear the problem and situation
my words is rude ,but ur words totally leading the guy into wrong direction ,and waste our time

o0k00l said:
Hi
Try this this i tried might be work for you too...
Put image file in root now run Task29 and as soon as the tri colour screen comes remove the usb cable and wait for 2 minutes it will search for serial and will automatically boot from SD image..
Thanx
Click to expand...
Click to collapse
bull**** 2
how could he do task29 with volume key and a flashed rom ?
dont wast our time

o0k00l said:
Hi
Try this this i tried might be work for you too...
Put image file in root now run Task29 and as soon as the tri colour screen comes remove the usb cable and wait for 2 minutes it will search for serial and will automatically boot from SD image..
Thanx
Click to expand...
Click to collapse
lol.. your barking at the wrong tree man.. read & understand

don't know if this is related but i thought i'd post it still.
i had an issue with task29 once i tried it.
usually, i flash roms using activesync since i'm kinda lazy putting back and fort the x1 cover, battery and all that.
after flashing task29, my x1 went dead. what i did, i removed the sd card,
plugged it to my pc and put the kovsimg file of the rom i like best,
plugged back in the sd card with the kovsimg file and re-flash via sd card method (using soft keys & volume button).
viola! it worked! but then again, i guess that's the way it's suppose to be done anyways.

simpleguy said:
how could your phone auto loading bootloader without a rom and volume down key press?
is your phone made from E.T ? he can do it auto intelligently
dont bull**** before u r clear the problem and situation
my words is rude ,but ur words totally leading the guy into wrong direction ,and waste our time
Click to expand...
Click to collapse
Ever did a bad flash???? Try it....flash from your pc and pull the USB cable. If you reset your phone where does it take you? Certainly not to boot the ROM, because the flash went wrong.
Well.....
As the OP doesn't tell us specific details about why or how his X1 has no ROM, I'm trying to get some more info on his problem.
So keep your rude words in your mouth before you speak...!
Since when does trying to help someone wastes your time???! Dude you really need to utter your frustrations somewhere else.
simpleguy said:
bull**** 2
how could he do task29 with volume key and a flashed rom ?
dont wast our time
Click to expand...
Click to collapse
Man...you're really sour aren't you?

Lokatho said:
Ever did a bad flash???? Try it....flash from your pc and pull the USB cable. If you reset your phone where does it take you? Certainly not to boot the ROM, because the flash went wrong.
Well.....
As the OP doesn't tell us specific details about why or how his X1 has no ROM, I'm trying to get some more info on his problem.
So keep your rude words in your mouth before you speak...!
Since when does trying to help someone wastes your time???! Dude you really need to utter your frustrations somewhere else.
Man...you're really sour aren't you?
Click to expand...
Click to collapse
laugh out loudly, bull**** again
his volume key is dead, and his phone dont have rom in it
and u, smart u , tell him flash a rom ? and pull cable blah blah
is it ridiculous?
how could he into bootloader in this situation?, perhpas u r god could let it done
once again, plz clear the situation, before you answer it(read op`s post again and again , ok ?)
u guys hand-up is appreciate ,but non-sense
u just waste our time
i wont relpy anymore untill u can provide a doable solution

simpleguy said:
laugh out loudly, bull**** again
his volume key is dead, and his phone dont have rom in it
and u, smart u , tell him flash a rom ? and pull cable blah blah
is it ridiculous?
how could he into bootloader in this situation?, perhpas u r god could let it done
once again, plz clear the situation, before you answer it(read op`s post again and again , ok ?)
u guys hand-up is appreciate ,but non-sense
u just waste our time
i wont relpy anymore untill u can provide a doable solution
Click to expand...
Click to collapse
Really sad.....I pity you.
As I want to help the OP, but as helping the OP wasted you're time I'm not. As I don't want to waste your time....

djromeo said:
had the same issue mate....and now my x1 is bricked!...couldn't do anything to get it back into tri-colour screen and sent it back to repair...tried to use the usb, mitty and nothing....good luck if you find another method....i hate task29 now i wouldn't try that thing again on my new phone...i did everything correctly and it just completely died on me...
Click to expand...
Click to collapse
thanks for helping mate, i will send my phone to sonyericsson shop wish they could help me

o0k00l said:
Hi
Try this this i tried might be work for you too...
Put image file in root now run Task29 and as soon as the tri colour screen comes remove the usb cable and wait for 2 minutes it will search for serial and will automatically boot from SD image..
Thanx
Click to expand...
Click to collapse
can u send me some details and steps how to do this, i will try it
thanks

simpleguy said:
laugh out loudly, bull**** again
his volume key is dead, and his phone dont have rom in it
and u, smart u , tell him flash a rom ? and pull cable blah blah
is it ridiculous?
how could he into bootloader in this situation?, perhpas u r god could let it done
once again, plz clear the situation, before you answer it(read op`s post again and again , ok ?)
u guys hand-up is appreciate ,but non-sense
u just waste our time
i wont relpy anymore untill u can provide a doable solution
Click to expand...
Click to collapse
guys come om plz i appreciate all your kind help really am desperate and wish i could get my phone back.
yup my phone has no rom so i couldnt flash any rom coz my volume key is died. NO NEW ROM AND NO BOOTLOADER.
i guess that there is no solution other than i should sent it back to the shop to be repaired but if there is a solution i wont regret to try it on my phone.
thanks all for your help.

Hello! I had this problem a minute ago. Try this:
1 -Turn on the phone. The screen will freeze in Sony Ericsson logo.
2 - After this, hold the two silver front buttons and press the softreset button behind the battery cover (to do a Hard Reset).
3 - Follow the instructions to perform the Hard Reset.
4 - When finished, remove the battery. Wait for 3 seconds and put the battery back.
5 - Now try to hold Vol Down key and turn the phone on.
It worked for me. But OMG, this thing scared me...

[Q] An huge problem!!

Sorry, but I have a big big problem. I have an x1, and I flashed the previous version of Energy Rom on the sd card. BUT I wanted to re-flash these, and the phone blocked in initial screen..the update rom one..
So, every time I try to update, it starts and after a few second, and when it start to update, the screen turns off. Finally, anyone can help me? I don't know how I can fix this situation PLEASE, HELP ME!!
Thanks, Fabio

Remove your Micro SD-CARD, and enter in flash mode! Volume down + power on!
Open the Update Phone Utility with the rom of your choice! Remember to rename your rom to: KOVSIMG.nbh
Sorry for English.

Faffa_mcr said:
Sorry, but I have a big big problem. I have an x1, and I flashed the previous version of Energy Rom on the sd card. BUT I wanted to re-flash these, and the phone blocked in initial screen..the update rom one..
So, every time I try to update, it starts and after a few second, and when it start to update, the screen turns off. Finally, anyone can help me? I don't know how I can fix this situation PLEASE, HELP ME!!
Thanks, Fabio
Click to expand...
Click to collapse
first time u must delete first the previous version on ur sd card... than u can update the new one... and dont forget to tasks 29 before u flash the rom...

Sorry guys, but when I enter in flash mode, and I press the power button and it should load the ROM, instead it always restart after 2-3 second. I don't know what to do..please help me!!

It sounds to me that you're not holding the buttons down correctly

paul c said:
It sounds to me that you're not holding the buttons down correctly
Click to expand...
Click to collapse
I tried again, but the result is the same.. uff..

hardspl
Faffa_mcr said:
I tried again, but the result is the same.. uff..
Click to expand...
Click to collapse
1. Try to pull up the batery for 10 menute.. and replace it again.. and press volume down and the power button together and dont realese until the boot screen appear...
2. connect ur x1 with the computer and hardspl the phone with the new spl 0.78.. when its finish the phone will restart.. pull the batery again for 1 menute.. and replace again... go to bootloader screen again like i explain in point 1.. after that conect again ur x1 with computer... do task29.. when finish its will restart again...
after u do task29.. u can flash ur x1 with the computer or with storage card..
this was the link for SPL 0.78 and task29 and if u still confused... http://www.826x.blogspot.com/
i think you can't flash the energy rom and always fail.. because u not hardspl your x1..

ahmadin said:
1. Try to pull up the batery for 10 menute.. and replace it again.. and press volume down and the power button together and dont realese until the boot screen appear...
2. connect ur x1 with the computer and hardspl the phone with the new spl 0.78.. when its finish the phone will restart.. pull the batery again for 1 menute.. and replace again... go to bootloader screen again like i explain in point 1.. after that conect again ur x1 with computer... do task29.. when finish its will restart again...
after u do task29.. u can flash ur x1 with the computer or with storage card..
this was the link for SPL 0.78 and task29 and if u still confused... http://www.826x.blogspot.com/
i think you can't flash the energy rom and always fail.. because u not hardspl your x1..
Click to expand...
Click to collapse
Sorry, I tried to connect the x1 to pc..but the pc doesn't recognize the phone..
I looked that the power button have a red light, and when this turn off, it go to bootloader mode, but after few second (it's in update mode) the phone turn off..
Someone has the same problem? I don't know what to do, I'm desperate! I can't use my phone

first remove sd card.
then pull out battery, press power button without battery on phone for about 30 sec.
then place battery. try to hard reset without OS:
press and hold both softkeys of X1, and press power button to turn on phone. but don't release softkeys until appears blue text with white background. slide put keyboard press R, wait to complete then press SPACE.
phone will be hard resetted. if not helped to boot OS, or there's no OS, or you did task29 before then do another task29 after this prosedure.
hope it helps

Faffa_mcr said:
Sorry, I tried to connect the x1 to pc..but the pc doesn't recognize the phone..
Click to expand...
Click to collapse
did you try another usb port of PC?

orkhanahmadov said:
did you try another usb port of PC?
Click to expand...
Click to collapse
mmm no...but I think that's another problem, coz when I put the phone on ac mode, it's the same situation...

orkhanahmadov said:
first remove sd card.
then pull out battery, press power button without battery on phone for about 30 sec.
then place battery. try to hard reset without OS:
press and hold both softkeys of X1, and press power button to turn on phone. but don't release softkeys until appears blue text with white background. slide put keyboard press R, wait to complete then press SPACE.
phone will be hard resetted. if not helped to boot OS, or there's no OS, or you did task29 before then do another task29 after this prosedure.
hope it helps
Click to expand...
Click to collapse
orkhanahmadov said:
did you try another usb port of PC?
Click to expand...
Click to collapse
Very good explaination....

Faffa_mcr said:
mmm no...but I think that's another problem, coz when I put the phone on ac mode, it's the same situation...
Click to expand...
Click to collapse
did you try method that wrote first.
and off course try another usb port, or another usb cable.
because if the phone did'nt recognized by PC, it means there's problem with cable or usb port if other things are OK.

[Q] samsung galaxy ace didnt automatically reboot after installing rom..

hi guys.. pls help me with my problem..
my samsung galaxy ace is now powerless, i cant turn the power on,, and i cant even charged it..
this is what happen. im on installation of roms for my unit, before all the instructions are done i thick its now totally brick..
after installing the rom it says installation conpleted but it didnt automatically reboot after that so i manual select reboot as i read in instruction but what i what wonder is it didnt automatically reboot.. after i manual reboot the unit it turns powerless and black out instead it will automatically boot but didnt.
now even i turn on the power button it didnt work, i push the home+power botton at the same but also didnt work, ive read some instructions on google on how to unbrick .. i push volume + and volume - at the same time then push power button but still it didnt turn on..
pls.. anybody can help me to fix my unit.. plsssss
tnx in advance for those who are going to help me..

excile25 said:
hi guys.. pls help me with my problem..
my samsung galaxy ace is now powerless, i cant turn the power on,, and i cant even charged it..
this is what happen. im on installation of roms for my unit, before all the instructions are done i thick its now totally brick..
after installing the rom it says installation conpleted but it didnt automatically reboot after that so i manual select reboot as i read in instruction but what i what wonder is it didnt automatically reboot.. after i manual reboot the unit it turns powerless and black out instead it will automatically boot but didnt.
now even i turn on the power button it didnt work, i push the home+power botton at the same but also didnt work, ive read some instructions on google on how to unbrick .. i push volume + and volume - at the same time then push power button but still it didnt turn on..
pls.. anybody can help me to fix my unit.. plsssss
tnx in advance for those who are going to help me..
Click to expand...
Click to collapse
Download mode can be accessed by holding Volume Down and Home and Power buttons together.
If nothing happens and you're sure that your battery has some remaining charge, then there's a good chance it is hard bricked.
You could also try a USB Jig (ebay is your friend) and see if that helps but otherwise it's off to the Samsung Service Center for you.

excile25 said:
hi guys.. pls help me with my problem..
my samsung galaxy ace is now powerless, i cant turn the power on,, and i cant even charged it..
this is what happen. im on installation of roms for my unit, before all the instructions are done i thick its now totally brick..
after installing the rom it says installation conpleted but it didnt automatically reboot after that so i manual select reboot as i read in instruction but what i what wonder is it didnt automatically reboot.. after i manual reboot the unit it turns powerless and black out instead it will automatically boot but didnt.
now even i turn on the power button it didnt work, i push the home+power botton at the same but also didnt work, ive read some instructions on google on how to unbrick .. i push volume + and volume - at the same time then push power button but still it didnt turn on..
pls.. anybody can help me to fix my unit.. plsssss
tnx in advance for those who are going to help me..
Click to expand...
Click to collapse
try to go in download mode by pressing vol down plus home plus power button simultaneously. if it goes in download mode then flash original firmware of your phone and restore it
and if it doesn't go in download mode then there is nothing much we can do,,,, you have to take it to service center
Sent from my fastest galaxy fit using xda premium app