Related
well long story short I used to have a wizard g3 and in a drunken rage I (with the phone) ended up in a lake. I had that phone fully cid unlocked and my ipl/spl was in the 2.xx range and I had an updated rom and what not. anyways I got the wizard replaced with my insurance thank god and i just got the new one today. now I'm going through updating my rom and such. anyways, I ran the lokwiz tool and sim unlocked and superCID unlocked my phone and I was going to go try some new roms, btw this replacement phone is also a G3 version. and so I came across http://forum.xda-developers.com/viewtopic.php?t=61997 NEW Custom 2.26 ROM with CF2-SP1 Flash7 Java Rings Themes...
but I was reading on there and it said that my IPL/SPL have to be version 2.xx or higher, now on my old phone it was that way, but on this one its like 1.08 and I dunno how I upgraded them before cause I can't remember. anyways, I've been searching on the forums for a few hours... I'll keep looking, I hate posting for help with out doing some thorough research. thanks for your help in advance.
I did some more reading and I guess the ipl/spl are usually included in new roms and it's just not included on this rom. is there any way to just update your ipl/spl, that would be your bootloader version, right?
screw it I cant just find a bootloader upgrade, doing a full rom upgrade just to get the new bootloader... kinda sucks but ohh well.
thats what I had to do I used the official tmob 2.26 rom which did my ipl/spl - bootloader, then I flashed xelencins 2.26 rom which is like a "tmobile light" cooked rom which I'd reccomend for any tmob usa users.
then I did the radio only to get cingulars radio rom
it worked out fine, the less you flash your bootloader the better, if you f-up a bootloader flash your phone is a brick, your bootloader is the failsafe if a rom update goes bad...
bhang
THIS IS NOT A THREAD ON HOW TO UNLOCK YOUR DEVICE
Ok, rather than crapping on Faria's thread, I am going to start a discussion. I am curious about the G4. Yes, I know curiousity killed the cat. So far, reading the forums we have some people with G4's that can upgrade no problem, some that had to CID unlock to get certain roms to load (Faria's), and some that even after CID unlocking the ROMs will not load the extended rom. Personally, I fall in the last category.
Now, here is what had made me curious: So far, most IPL/SPL I have seen posted about is 2.21.0001 for the G4. Mine, on the other hand is 2.25.0001. So, for thos that have G4s, make a post about your IPL/SPL, if you had to CID unlock, HOW you unlocked, and your measure of success. Faria and I were discussing the possiblity that more is tied to the IPL/SPL than on the G3s. Or they are using tighter security. So if we have people with IPLs of 2.21.0001 that can load the full ROM after CID unlocking, and those that have 2.25.0001 that get the OS, but not the extended rom..it gives us a clue.
cptcafne said:
THIS IS NOT A THREAD ON HOW TO UNLOCK YOUR DEVICE
Ok, rather than crapping on Faria's thread, I am going to start a discussion. I am curious about the G4. Yes, I know curiousity killed the cat. So far, reading the forums we have some people with G4's that can upgrade no problem, some that had to CID unlock to get certain roms to load (Faria's), and some that even after CID unlocking the ROMs will not load the extended rom. Personally, I fall in the last category.
Now, here is what had made me curious: So far, most IPL/SPL I have seen posted about is 2.21.0001 for the G4. Mine, on the other hand is 2.25.0001. So, for thos that have G4s, make a post about your IPL/SPL, if you had to CID unlock, HOW you unlocked, and your measure of success. Faria and I were discussing the possiblity that more is tied to the IPL/SPL than on the G3s. Or they are using tighter security. So if we have people with IPLs of 2.21.0001 that can load the full ROM after CID unlocking, and those that have 2.25.0001 that get the OS, but not the extended rom..it gives us a clue.
Click to expand...
Click to collapse
I have a G4
I am
IPL 2.17.0001
SPL 2.17.0001
GSM 02.07.10
OS 2.17.7.2
I am still CID locked, and have not attempted to perform any ROM upgrades yet
I want to CID unlock my device so that i can do a rom backup to the SD card before attempting any kind of ROM upgrades.
How did you unlock your G4 device?
d0ug said:
I have a G4
I am
IPL 2.17.0001
SPL 2.17.0001
GSM 02.07.10
OS 2.17.7.2
How did you unlock your G4 device?
Click to expand...
Click to collapse
Imei website. search for it
imei did it for me
IPL/SPL = 2.17.0001 which means I have a G4.
I ended up paying for unlocking at the imei website but it did the trick and solved my issues where previously i could only get the Mr Clean ROM upgrade to work. Other ROMs would only update the splash screen and the Extension ROM.
Yesterday I successfully updated to Faria's latest RC1 ROM with no issues.
cptcafne said:
Imei website. search for it
Click to expand...
Click to collapse
Thanks, I knew of the site, I just wasnt sure if it was a CID unlock or only SIM unlock. There was a post this morning about it only being a SIM unlock.
I got a CID-LOCKED G4:
IPL 2.21.0001
SPL 2.21.0001
OS 2.26.10.2
GSM 02.25.11
I succesfully installed:
RUU_Molski.Biz_226102_22610105_022511_G4_WWE-30MB
RUU_Molski.Biz_226102_22610105_022511_G4_WWE
Couldn't install:
RUU_Molski.Biz_AKU2.3-226102_22610105_024711_WWE-G4-30MB-CF2
Installer said something about compatibility issues
Didn't dare trying to install Faria new rom yet.
IPL/SPL 2.25.0001
CID locked G4
Extension ROM locked and empty after a failed flash with the official 2.25 ROM on HTC site, can't get anything to install into it. I've since learned to live with it and hope Cingular/HTC will release a newer ROM update that will fix this issue. I'm actually looking into upgrading to a 8525 but those suckers are a bit pricey at the moment so staying with my 8125 for now.
My G4 with bootloader 2.16.0001 had unlock with imei-check.co.uk. You can do it at the same site for 20GBP and U can successfully install any ROM (shipped or custom) without bootloader (I mean IPL/SPL). I recommended to stay in your current latest version of official ROM's bootloader and you will not have any issue.
Nishad
evilito said:
IPL/SPL 2.25.0001
CID locked G4
Extension ROM locked and empty after a failed flash with the official 2.25 ROM on HTC site, can't get anything to install into it. I've since learned to live with it and hope Cingular/HTC will release a newer ROM update that will fix this issue. I'm actually looking into upgrading to a 8525 but those suckers are a bit pricey at the moment so staying with my 8125 for now.
Click to expand...
Click to collapse
That is exactly what happened to me!! Tried the HTC rom, and it killed my extended rom. crap. ok so HTC did this to us. I wonder how many other members tried the "official" rom and it crashed, therefore have not been able to get any extended rom loaded.
Same issue here with the extended ROM and 2.25.0001
The shipped ROM for cingular 8125 would fail.
Had to cook my own ROM and manually put the Extended_ROM folder in root and run the AutoRun.exe from phone to load it.
I was trying to find the way, how to cook a ROM, whitch will work on CID-locked Wizards and I thing: On CID locked phones we can flash only ROMs with nono edited os.nb without IPL/SPL
Example:
I have had a 2.21 ROM a I was able to flash 2.26.10.2 ROM without any changes.
If a decrasing the Pagepool, the the ROM was not working on CID locked
cptcafne,
I am sure you have seen my posts in faria's thread, but I will add my woes to this thread as well.
I have a 2.25.0001 G4 Wizard.
After doing the CID Unlocking through IMEI, I attempted to load faria's beta 4 rom. The ext rom has never installed for me. I think I might have tried installing the rom image from the htc website over the rom that shipped since I thought the HTC rom was newer (I was wrong). I belive this locked my ext rom from the get go. After testing it, I wanted to go back to the cingular 2.25 offcial rom to have a stable base to install the RC1. However, I got when re flashing the 2.25 rom I receive the invalid nb.nkf error message.
If Broken has cooked is own extended rom which has worked on his G4, perhaps a seperate G4 ext rom file is the resolution that faria should seek if there is no success in automating the process in the flash.
I wonder if the locking of the ext rom is an HTC or Cingular thing. Either way I wonder if they have the ability to tell us how to unlock the ext rom?
G4 unlocked by IMEI
IPL/SPL 2.16.0001
Radio 2.47.11
ROM 3.0.0.0 WWE
Faria's 8mb ROM installed without any problems (including the ExtROM) been running OK for about a week and only the occasional soft reset.
Installed over wizard Love 2.26 ROM
hello,
G4 Not unlocked :
IPL/SPL 2.17.0001
No rom upgrade possible
G4 2.17.0001
Qtek 9100
IPL/SPL 2.17.0001
CID unlocked by the IMEI UK site.
Running the latest 3.0.0 RC1 Faria ROM - no issues with the upgrade.
Prior to CID unlock I could only upgrade the splash screen and the ExtROM.
I haven't had the nerve to attempt an IPL/SPL upgrade - not even sure what benefits it would bring.
In this thread (http://forum.xda-developers.com/showthread.php?t=249359&highlight=unlock+extended+rom) there is a way to unlock the extended Rom. However when I do this, all I see is the cingular ext rom files that are installed during the "customization" process. I am wondering if Cingular is in fact locking the ext rom so that no matter what ROM is flashed the ext rom will always contain the Cingular programs and files that were shipped with the phone.
I have yet to see a user with an IPL/SPL of 2.25.0001 be able to install any ext roms.
Jason
fla242 said:
hello,
G4 Not unlocked :
IPL/SPL 2.17.001
No rom upgrade possible
Click to expand...
Click to collapse
are you sure your device is G4????? cuz ipl spl are ends with .001 not .0001
Awais said:
are you sure your device is G4????? cuz ipl spl are ends with .001 not .0001
Click to expand...
Click to collapse
Just to clarify, G4 devices have an IPL/SPL of 2.xx.0001. If the IPL/SPL do not appear in that format when you reset your device than you have a G3 device.
jpryor said:
cptcafne,
I am sure you have seen my posts in faria's thread, but I will add my woes to this thread as well.
I have a 2.25.0001 G4 Wizard.
After doing the CID Unlocking through IMEI, I attempted to load faria's beta 4 rom. The ext rom has never installed for me. I think I might have tried installing the rom image from the htc website over the rom that shipped since I thought the HTC rom was newer (I was wrong). I belive this locked my ext rom from the get go. After testing it, I wanted to go back to the cingular 2.25 offcial rom to have a stable base to install the RC1. However, I got when re flashing the 2.25 rom I receive the invalid nb.nkf error message.
If Broken has cooked is own extended rom which has worked on his G4, perhaps a seperate G4 ext rom file is the resolution that faria should seek if there is no success in automating the process in the flash.
I wonder if the locking of the ext rom is an HTC or Cingular thing. Either way I wonder if they have the ability to tell us how to unlock the ext rom?
Click to expand...
Click to collapse
Yeah, that is what looks like happened. so far from what I seen on the boards, if someone tried to install the HTC Update and it failed, then the ext rom was locked. or even removed, I am not sure.
Jpryor said:
In this thread (http://forum.xda-developers.com/show...extended+ rom) there is a way to unlock the extended Rom. However when I do this, all I see is the cingular ext rom files that are installed during the "customization" process. I am wondering if Cingular is in fact locking the ext rom so that no matter what ROM is flashed the ext rom will always contain the Cingular programs and files that were shipped with the phone.
I have yet to see a user with an IPL/SPL of 2.25.0001 be able to install any ext roms.
Jason
Click to expand...
Click to collapse
Are you sure ? I could have sworn that some members with 2.25.0001 were able to install custom roms completely. Can anyone confirm this for us ?
I have a G4, and the original IPL/SPL was 2.25.0001. I tried all the free options to CID unlock (they worked for SIM unlock), but not worked. So I paid the £20 to IMEI-Check for the unlock key. With that I fully CID unlocked my device.
I installed the stock T-Mobile USA 2.26 ROM, and now my IPL/SPL is 2.26.0001. (I switched carriers from Cingular to T-Mobile, but prefer the 8125's keyboard to the MDA's, so I wanted to keep my existing device.)
I just upgraded my QTEK 9100 with the latest RIsidoro rom and have now a 2.26 OS but...always an ipl 1.03 and a spl 1.03.0000.
The device hangs and I can't have any activsync runnuing to reflash to an other version. How can I recuperate my PPC?
Thanks in advance
sailors_be said:
I just upgraded my QTEK 9100 with the latest RIsidoro rom and have now a 2.26 OS but...always an ipl 1.03 and a spl 1.03.0000.
The device hangs and I can't have any activsync runnuing to reflash to an other version. How can I recuperate my PPC?
Thanks in advance
Click to expand...
Click to collapse
To get you started have a look at these threads:
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
http://forum.xda-developers.com/showthread.php?t=263116
http://forum.xda-developers.com/showthread.php?t=282498
http://forum.xda-developers.com/showthread.php?t=284292
More info required.
When having problems with Rom Upgrades you really need to provide as much information as possible about your situation.
Please state the following:
What Rom did you have prior to upgrading, include IPL/SPL numbers.
Do you know if your device is G3 or G4 flash chip?
Is your device CID Unlocked?
Have your read (thoroughly) the instructions provided for the Rom you attempted to upgrade?
My initial guess would be that the Rom you flashed doesn't include IPL/SPL (as Risidoro clearly states in the Original Post (http://forum.xda-developers.com/showthread.php?t=276700)
In this case, you need to flash one of the Operator provided AKU 2.x Roms to get your IPL/SPL up to 2.x BEFORE you flash Risidoro's Rom to your device.
Thank you for you reaction
Before flashing I had following situation
IPL 1.03
SPL 1.03.0000
GSM 1.410.0
OS 1.37.10
I didn't saw the thread wher it said that the isodoro flash wasn't a complete one. So I upgraded the device with this rom on the above config
After flashing with Isodoro I have same IPL and SPL no GSM anymore and OS 2.26...
I have no USB connection anymore, I supose I can not flash anymore. The device is extremely slow. The only rescue I see is eventualy to flash the device again with the mini SD.
Before I started the first flash I did a CID unlock. Actualy i don't now if it is locked again.
If tou need more info don't hesitate and thanks for helping.
I'm going to give you some general info but you will have to do your own leg work to put this together.
The Wizard Wiki will contain some of the information you need:
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
Also see the stickied posts at the beginning of the Wizard upgrading forum.
I am assuming that your device is not properly CID Unlocked (although it may be doing it again will not harm your device).
First you will need to download an Operator Rom, I would suggest this one:
ftp://xda:[email protected]_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe
as it is an official Qtek AKU 1.x Rom.
Second place your Device into Bootloader Mode (search on it) and run the update that you downloaded.
At this point you are pretty close to where you were when you started.
Now, CID Unlock your Phone! Use this thread:
http://forum.xda-developers.com/showthread.php?t=249474
If you have followed the instructions and everything went okay then you can now flash any of the Roms you (except one that are marked as G4 only since you appear to have a G3 Device).
sailors_be said:
Thank you for you reaction
Before flashing I had following situation
IPL 1.03
SPL 1.03.0000
GSM 1.410.0
OS 1.37.10
I didn't saw the thread wher it said that the isodoro flash wasn't a complete one. So I upgraded the device with this rom on the above config
After flashing with Isodoro I have same IPL and SPL no GSM anymore and OS 2.26...
I have no USB connection anymore, I supose I can not flash anymore. The device is extremely slow. The only rescue I see is eventualy to flash the device again with the mini SD.
Before I started the first flash I did a CID unlock. Actualy i don't now if it is locked again.
If tou need more info don't hesitate and thanks for helping.
Click to expand...
Click to collapse
Looks like you flashed a 2.xx rom with no bootloader into a 1.xx system.
First try a full 2.xx rom from a carrier (cingular 2.25 comes to mind) then reflash the rom you want. Be careful playing with the phone in the current state as the battery will drain and not re-charge. I had to have a friend charge my battery for me when I did this same thing.
many thanks
I followed the procedure you give and recuperated my phone.
Thanks a lot for the assistance.
Merry christmas and happy new year
Jean-Michel
I downloaded Viet4 and run upgrade, on welcome screen on PC during upgrade it does not correctly detect my Wizard and shows as ROM 1.0.0 and for new version it says only blanks.
After upgrade device just boots to previous version of the ROM (2.26). What am I doing wrong?
Let me be the first one to say it before someone else does... Read the Wiki
Joking aside, you need to give more info such as do you have a G3 or G4? Did you CID unlocked your device? The error you have given usually meant that your device is CID locked.
artisticcheese said:
I downloaded Viet4 and run upgrade, on welcome screen on PC during upgrade it does not correctly detect my Wizard and shows as ROM 1.0.0 and for new version it says only blanks.
After upgrade device just boots to previous version of the ROM (2.26). What am I doing wrong?
Click to expand...
Click to collapse
sounds like you didn't CID unlock before trying to flash a rom that didn't come from your carrier.
and the upgrade tool will not have the right info in those fields. If your phone is unlocked the upgrade will work properly. Make sure you use the correct procedure based on whether you have a G3 or G4 phone.
I have G3 device
I have Qtek 9100 which was never locked of course. Then I installed ROM and radio upgrade with versions below
ROM version: 2.26.10.2 WWE
ROM date: 6/7/06
Radio version: 02.25.11
Protocol version: 4.1.13.12
Hardware:
CPU:OMAP850
Flash chip type:M-Systems
What do I do now?
artisticcheese said:
I have Qtek 9100 which was never locked of course. Then I installed ROM and radio upgrade with versions below
ROM version: 2.26.10.2 WWE
ROM date: 6/7/06
Radio version: 02.25.11
Protocol version: 4.1.13.12
Hardware:
CPU:OMAP850
Flash chip type:M-Systems
What do I do now?
Click to expand...
Click to collapse
What is your IPL/SPL. And how do you know it was never locked? Have you personally unlocked it? Have you ever flashed any rom that was not from your carrier successfully?
If you have a G3 (ipl/spl 2.26/2.26) then I suggest following the full unlocking tutorial thread that is stickied. Trust me your phone is acting like a locked phone. If you haven't personally unlocked it then just humor us and do this. You will be amazed at the results.
If you have a G4 (ipl/spl 2.26.0001/2.26.0001) then you will have to use the pay website to unlock your phone. There is no other known way to unlock G4 devices at this time.
I assume since it was bought in Russia and branded as Qtek 9100 then it was not locked. Is it possible that ROM upgrade to Cingular ROM actually locked my phone?
SPL 2.26/2.26
I going through downgrade right now and then do CID unlock. Do I have to do SIM unlock as well? How do I know if device is unlocked?
artisticcheese said:
I assume since it was bought in Russia and branded as Qtek 9100 then it was not locked. Is it possible that ROM upgrade to Cingular ROM actually locked my phone?
SPL 2.26/2.26
I going through downgrade right now and then do CID unlock. Do I have to do SIM unlock as well? How do I know if device is unlocked?
Click to expand...
Click to collapse
SIM unlock will allow you to use any sim from any carrier without getting an invalid sim error. If you aren't getting this error already you should be ok not doing it but it doesn't hurt to do it since you are in there with Lokiwiz already.
The tutorial tells you to do the SIM unlock first then do the CID unlock.
once you are completely done don't forget to flash up to a 2.x rom (2.26 T-Mobile rom suggested) before flashing a custom rom.
At this point when you flash the custom rom your OS and possibly GSM will change (IPL/SPL may change if you use a rom that includes them)
You should be good to go once the CID unlock process is done completely.
I used Unlock and CID Unlock, both went fine. Now IPL 1.01 SPL 2.26 OS 1.5.4.2.
Do I need to upgrade to 2.X before upgrading to WM6 or I can run upgrade the way it is now? Do I need to upgrade IPL (whatever it is to 2.26 as it was before?)
THanks,
artisticcheese said:
I used Unlock and CID Unlock, both went fine. Now IPL 1.01 SPL 2.26 OS 1.5.4.2.
Do I need to upgrade to 2.X before upgrading to WM6 or I can run upgrade the way it is now? Do I need to upgrade IPL (whatever it is to 2.26 as it was before?)
THanks,
Click to expand...
Click to collapse
Right now you need to install the button rom again to get both IPL and SPL to 1.05. At that point you can flash back up to 2.26 and then to a custom rom of your choice.
The reflash of the button 1.05 rom is to ensure that you are truly unlocked. you will see that both IPL and SPL go to 1.05 -- this is good
The flash to a carrier 2.x rom is so that you have a good 2.x bootloader and don't inadvertantly flash a 2.x rom without bootloaders into 1.x bootloaders which will cause all kinds of issues.
Yes, you must flash a full 2.x rom before flashing the wm6 rom. The T-Mobile 2.26 is the recommended rom as it has the latest bootloaders available.
Then you go to the rom of your choice and enjoy
I know it's a pain in the behind but it is tried and true
Thanks,
This worked. The only issue now after I installed WM6 it starts installing some T-Mobile crap which appears belongs to 2.26 ROM I installed before. How can I clean install of WM6 without any T-Mobile stuff?
Thanks,
artisticcheese said:
Thanks,
This worked. The only issue now after I installed WM6 it starts installing some T-Mobile crap which appears belongs to 2.26 ROM I installed before. How can I clean install of WM6 without any T-Mobile stuff?
Thanks,
Click to expand...
Click to collapse
Might have to flash a rom that has an empty extended rom before going to the one you went to. My guess is that the rom you flashed did not include an extended rom and when you flashed it the customizations ran from the previous roms extended rom since it was still there.
Faria's 3.3 v2 has a settings chooser menu so you can select settings for whichever network you are on but that only sets up MMS/GPRS stuff, and doesn't install any carrier specific apps.
Never mind, I recovered using some old iMate ROM. The problem now is that iMate ROM updated SPL/IPL to 2.16 while I had 2.26 for both before. Is it ok to run with 2.16 or there might be some issues? What is SPL/SPL are used for?
artisticcheese said:
Never mind, I recovered using some old iMate ROM. The problem now is that iMate ROM updated SPL/IPL to 2.16 while I had 2.26 for both before. Is it ok to run with 2.16 or there might be some issues? What is SPL/SPL are used for?
Click to expand...
Click to collapse
2.16 should be fine. It is 2.xx and that is what really matters.
The issue that some people encounter is flashing an AKU2 or higher ROM into 1.xx bootloaders and have all sorts of issues, phone won't charge, radio doesn't show up, pda works but phone doesn't, battery drains quickly and no way to recharge, etc.
I am pulling my hair out here...
I have an 8125, with the following
Sim Carrier and Rom = T-Mobile
IPL/SPL=3.08
GSM=01.12.10
OS=1.5.4.2
Rom Version=1.5.4.2 WWE
Radio Version 01.12.10
I followed the two main tutorials on how to SIM and CID unlock, got both my IPL and SPL to match, flashed in the TMo Rom and thought all was good.
Now I was poking around and see that it is not a 2.26 rom that is on there but it is a 1.5.4.2. So what do I do, I go to
http://www.t-mobile.com/wmupgrade/
to get the Mobile MDA Software Version (2.26.10.2)
and when I run the file that gets downloaded, it gives me a
ERROR [296] : UPGRADE ONLY
Now, does it see that the phone is infact not an MDA and is a 8125 and does not like it?
So now from this point, (I have done my research and forum search, and RTFM many times so pleae dont blast me) what do I need to do to get the updated 2.26 rom, and eventually get up to the WM6.
I appreciate all the help, as I am seriously ready to have phone meet wall.
177media said:
I am pulling my hair out here...
I have an 8125, with the following
Sim Carrier and Rom = T-Mobile
IPL/SPL=3.08
GSM=01.12.10
OS=1.5.4.2
Rom Version=1.5.4.2 WWE
Radio Version 01.12.10
I followed the two main tutorials on how to SIM and CID unlock, got both my IPL and SPL to match, flashed in the TMo Rom and thought all was good.
Now I was poking around and see that it is not a 2.26 rom that is on there but it is a 1.5.4.2. So what do I do, I go to
http://www.t-mobile.com/wmupgrade/
to get the Mobile MDA Software Version (2.26.10.2)
and when I run the file that gets downloaded, it gives me a
ERROR [296] : UPGRADE ONLY
Now, does it see that the phone is infact not an MDA and is a 8125 and does not like it?
So now from this point, (I have done my research and forum search, and RTFM many times so pleae dont blast me) what do I need to do to get the updated 2.26 rom, and eventually get up to the WM6.
I appreciate all the help, as I am seriously ready to have phone meet wall.
Click to expand...
Click to collapse
You have already flashed newer bootloaders that 2.26. You have 3.08. Why do you need to go back to 2.26? IF you are CID unlocked (did you take your bootloaders down to 1.xx then run lokiwiz, and then bring them up to 3.08?) you should be able to flash your WM6 rom now. Have you tried?
Zzan said:
You have already flashed newer bootloaders that 2.26. You have 3.08. Why do you need to go back to 2.26? IF you are CID unlocked (did you take your bootloaders down to 1.xx then run lokiwiz, and then bring them up to 3.08?) you should be able to flash your WM6 rom now. Have you tried?
Click to expand...
Click to collapse
I think he upgraded the IPL/SPL alone from button's 1.01 and now can't flash any ROM since 3.08 can't handle 1.5 OS.
My advise is to flash IPL/SPL 1.01 and from there flash a 2.26 but... there are a lot of people mentioning IPL 3.08 and SPL 1.xx meaning that IPL won't allow to downgrade. I think it's up to him...
my understanding is that you shouldn't be going to an ipl/spl of 3.xx unless you are flashing from an ipl/spl of 2.xx. (based on thread information from old roms of molski and faria, last days of wm5 roms).
if possible, you should try to reflash back to 1.05 (i think they were customized so you shouldn't have problems).
official t-mobile roms won't let you downgrade to my understanding...at least not from one official t-mobile to another official (3.08 --> 2.26 or 2.26 -->1.80).
so...retry to flash buttons 1.05, then move up to 2.26...and then if you really want to flash again to 3.08.
That is exactly what I figured out last night.
When I RTFM where it says EDIT STEP 17: Flash to 3.08 .......
I took that as a instad of thinking that it contained the 2.16 rom as well as the IPL/SPL upgrades.
So I went through reflashed both back down to buttons 1.05 and then reflashed back up to 2.26 and then to WM6, everything is dandy and it is all becuase of the wonderful people here. I can not say it enough. This place is the greatest! And thank you all yet again.
I'm glad you managed to save your phone. Not many these days by counting the number of "Help" threads
Can i ask you to please give something back to the forum? please check my signature and visit the "Data crashes" solution thread. Tx
Definitly will.