During ROM upgrade i accidentally pressed cancel button
after that the BA looks like it's completely dead - it won't power on, can't enter bootloader mode, can't hard/soft reset, no lights
(i thinked that i am quite experienced with all that -- did rom upgrade/downgrade many times but now i'm confused)
what to do?
Take out the battery and leav out for a while
This seemed to bring it back to life when I did this some time ago
did that already
are 12 hours enough?
be - dead, or not.
Hey
Have once the same problem, and as i remember, i pressed 2 buttons and hold them, meanwhile i press power, after (ie) 10 sec, release buttons, then it have the be in the craddle, and on the screen it says (as i can remenber) "serial xxx" switching on to "USB xxx" and then the official release- coud wake it, and then it installed.
Remember to disable the firewall, it fooled me some times...
Hope you anderstand what i meen, or else ask again.
Good lock... the BE is a splendid phone, if the software is ok
/Nmouse
o2 xda2s - won't wake ?
been there, suffered from that!
remove battery, insert battery ('don't count, It'll only make things worse!' )
- watch for red version numbers down at bottom of the screen, if all 3 [r,g,b,]clip the battery clip to up/hold. and booting should start,
-= mabey looky @ wiki 4the '4 bar menu' <switch 2 and 3 only!> ??? =-
as many as 15 goes (tried shorting the 5/6 pins on the ba, battery has 2 silver connections at bottom ( and the 5/6 at the top ) of battery, face/clean - make a circuit?)
upto 15 times this bad radio rom stopped the bootin' . . . then ka Pow!!!
t-mob's rom (4 the O2 xda 95/100 -reliability {toooo many apps/games }
***can any body help ' wm5 for all ba devs.pdf ' @2008***
***all steps followed to the letter . . . step 10 ?? error ***
***5.1.1700_build_14343_Up/Gd . .r2300_d1390. ***
*** err120 = 22-22-12-n-n _-= cb2.07 - - - - '-1'***
*** t-mob rom on O2 xda2s = ??? editfix ? <step 8(b)>???***
i'm here all week, tip yer bar person #===#===# -d.b- #===#===#
vaseline + silicone = comfy holder ""
O M G - works ???
I ran baUpGd
<got err's above !!!>, &
I then ran MaUpGd = runnin'
Blue tooth seems okay
#===#===#
II _d.b_ II
#===#===#
-'every penny'- tbc . . .
Related
Recently I am experience and incredible fact.
The green button to start a call NOW works as CALENDAR shortcut button (yes like the top right button)
The red button to END a call NOW works as CONTACT shortcut button (yes like the top LEFT button)
The 2 Contact and Calendar button (top left and right) DO work correctly.
I supposed some recently installed applications made this mess. Therefore I tried
- soft reset: no way
- hard reset: no way
- I PUT MDA 3 in BootLoader mode and I REINSTALLED MY rom 1.42 WWE
Now what happened is that for 2 days OK, the GREEN and RED button DID work correctly to start and end CALLS.
After 2 days, the strange phenomena appeared again!
Please note that I HAVE NOT INSTALLED ANY ADDITIONAL SOFTWARE!
I am very puzzled.
Please help
Saulo
Any suggestions
Any suggestions
I am getting crazy at this behavour...did i get a virus?
Thanks and waiting
Saulo
help me
my wiza200 is totaly dead
i downgrade it to 1.01 than i write spl of 3.08 and that is the big mistake i have every done..
so my phone is not power on or not go to bootmode
what to do now
any one have any solution?
please help
or is there any way to start phone is bootmode???
Yes there is a way.
I took the following from the Wizard Wiki
''To go to the 3 coloured bars , just press and hold the power button (top) + voicedial button(right top) keep it pressed and hit the soft reset hole (keep the other 2 buttons pressed until the 3 coloured bars come up)''.-
still not work?
i try many times but still not goes in bootmode?
help me please
Are you sure that you are doing it right?
Maybe you are skipping some part like: keep the other 2 buttons pressed until the 3 coloured bars come up
I have tried it to my phone & it is working.
When you try that I have told you what happens to your Wizard?
history of my phone
sir
i try this trick but useless (i press these 2 button upto 5 to 10 min after hitting the soft reset button) but not work!!!
so i tell you my phone history now
the phone was lock to t-mobile than i read one blog in this forum that if u want to unlock phone than u want downgrade the phone to version 1.XX
than unlock it.
so i downgrade the phone to 1.01 my phone is G3.
than after my big mistake is that i write Spl version 3.08 to my phone directly
than than phone is dead not even goes to bootmode.
is there any way to flash my test point ??
thank you
Well...
That's how far I can go .
I can't help you further but I will suggest you to take a look at the thread Dead WIZARD? Never! Let's REVIVE!.
Maybe you will find the solution of your problem there.If not maybe you should make a post there.
Also if you search a bit at xda you will find some more threads about bricked Wizards that will help you.
I hope you will find solution to your problem.-
Same problem .................
hi there,
this morning, without any interactiom, i heard the vibration of my touch diamond restarting.(with original newest ROM from htc website that ran without any problem for several months). battery was about 80% yesterday evening.
but it wasn´t starting at all. after the HTC animation and the green windows mobile screen, it started again. after restarting for 20 minutes i took out the battery, put it in again and performed a hard reset as stated in the manual.
now, on the "rainbow" screen i get a message like
psoc diam stage_pvt 0x32
then i did the Volume-Up reset, and now i don´t even get the red version information in the lower right screen. as it doesn´t even start i cannot get an active sync connection.
any ideas? is my phone broken? i didn´t do anything special, and i wonder why it rebooted without interaction this morning.
any ideas what i can do?
thanks in advance,
jkersch
Mine started doing this about 2 weeks ago it woke me up in the middle of night while sleeping with its vibrator and start sound.
The only thing I have found is that my little reset button at the pen holder dosent work anymore. To do a hard reset i have to takeout the battery and then put it in, hold the volume key and enter key then power it to get it. Flashed by holding volume down and the power on, it hold for about 10min just enough to get the flash.
I managed to flash it once but it dosent help, it constantly reset at the thouch diamond screen. Some times i get to the green windows mobile screen.
As warrenty is out on my phone and ive given up and using another phone.
Same problem in a different thread
Have a look at http://forum.xda-developers.com/showthread.php?p=5279740.
install a new radio worked for me
Hi, I'm new to XDA Dveloper. sorry if its already questioned..I don't have time to search for them, I'm running my laptop on battery that only will last about 15 minutes..and I have my electricity out..
Yesterday, I got My diamond exposed to water...it was raining hard and I was on my bike with my diamond in my pocket..
when I got home, my diamond begin to act strangely, it keeps lower its volume(to vibrate state) when I try to press the increase volume rocker, it goes back down to vibrate. but I manage to shut it down with slide2shutdown...and charge it (the battery only 7% left). this morning I get up and switch on the diamond, but It doesn't boot like usual(theTOUCHDiamond sceen)...
it only shows 4 bars (RED, GREEN, BLUE, and WHITE)consist of:
RED BAR with this:
DIAM100 64M
SPL-1.37.Olinex
MicroP-Diam (LED) v11
GREEN Bar with:
PSOC-Diam Stage_PVT v0x30
BLUE Bar : blank
WHITE Bar with
Serial (only "serial is written, nothing more)
That all, and when I try to connect with USB cable, it demands Qualcomm CDMA Drivers...(I use My friend's laptop....no activesync installed)
anyhelp would be appreciated.
thanks
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
bellsprout said:
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
Click to expand...
Click to collapse
what are you trying to hardreset device..??
A hard reset should only be performed if a normal reset does not solve a system
problem. After a hard reset, the device is restored to its default settings—
the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows Mobile® software and other pre-installed programs will remain.
Try flashing back to stock rom?
Sent from my GT-P1000 using XDA App
Hi!
I have a boot problem also.
I used Memo ROM about 1 month ago. That was worked well still today. I restarted my Diamond today, it was not boot correctly. Only reboot the phone after showing the ROM information. I made hard reset and put back the rom again, but the phone is not boot properly.
Could to help somebody for me?
I solved the problem.
I downloaded the original rom (included with radio rom) from htc.com.
I put the phone to bootloader mode and flashed this original ROM.
After flashing finished, my diamond boot to WM6.1.
I don't know what was the problem, but it works again...
I hope never happening this again!
One M7 : Black screen, only green led and home buttons are "ON"
Hello,
First of all, sorry for my english, i didn't practise for many years ^^
So, here we go :
'Got a regular HTC One M7, converted into a google play edition, 5.0.2, rooted and s-off, and twrp installed (for a couple of month now).
Yesterday, i came back from holidays, so i put my phone on a car support, and i used it as a gps (9 hours to come back, and use phone for 4 hours, but not in one time : 1 hour use, pause for 1 hour, 1 hour use...etc...) with maps.
All was ok, phone was hot but not "very very hot" (full sun in france ^^). When i was at home, i let it at house, and plug it from 23h to 09h this morning. I used it on 23h, playing game and surfing on web, then go to sleep. And this morning, alarm phone didn't ring, so i take my phone and see only a black screen, with green led and home / back button ON.
Try to reboot by many ways : 10 seconds on power button, 20sec, 1min....no way !! I just see home and back buttons flashing as long as i push on power button
Try to reboot with power button and vol + or vol -.....no way...
Plug it on my windows 7 64bits pc : just detect a cd drive with nothing else.....
Phone was out of guarantee, so what can i do ?
Is anyone already have the same problem ?
Thans for any help, David :good:
Hum, seems it is working now :
I push power button for a very very long time (near from 2/3 minutes) and phone reboot !!
Phone looks a little slower, but it's working !!
I'll be waiting a couple of days, but i think i'll probably wipe it totally (cache +data) if it's going too slow.
So, if anyone have the same issue...push power button as long as your finger can :good: