If I dial a number and press the connect button on my Diamond the call will not be put through.
I have to first save the number into my contacts and then browse my contacts and hit connect to make a call.
A friend of mine has the same problem on his S710 so I think this must be a setting thing rather than a problem thing with my Diamond.
Anyone got any ideas?
Thanks for the help!
I was having the same problem. Did you install AE button plus or another key mapper? This was what caused my problem when I remapped the green button single click to "phone" instead of "press green button".
Haven't installed any key mappers, came like this out of the box.
I sent the phone in for repairs last Friday. It was getting boiling hot on charge or GPS, then on Thursday nught the screen stopped working.
The guys at HTC say the main board and the screen bezel are both buggered and so the will replace the parts by Friday!
Thanks for your help though.
Related
Hi
I don't know if anyone has experienced this or has a fix for it.
I picked up my Tytn II last week and I must say it's a cracking piece of kit. I seem to be experiencing a problem though.
If I say for example make a voice call and then hang up. I find that the word "phone" replaces the start menu in the top left hand corner of the screen. This wont default back to start and effectively makes the whole top row of icons inoperable. Ie battery status volume control etc. I have found this problem when using other apps, ie calendar, so it's not specific to just making voice calls.
The only way to get the top row of icons working again is to do a soft reset
All icons not on the top row seem to work ok (apart from keylock)
Any ideas ??
Massiv
Dont soft reset... just hit the power button to go into standby, then hit it again and the device will work again.
Hey presto it worked. Thanks for that. It's a bit annoying having to do that though.
Massiv
Its not a fix... its just a workaround.
When you end calls. Try first pressing the end call button, then the ok button.
Hello, sometimes after i finish a call, or when i use audio manager when i finish and hit the x close button, i go back to the today screen, but nothing recognizes my touch after that...but i noticed that instead of it saying 'start' at the top of the list, it would say call or audio manager or whatever program i was using before it 'froze'.
The only way to stop that and bring it back to normal was to press the power button and then press it again (not turn off the phone, but put it in the 'standy' ish state)
Anyone know why this is happening and if there is a patch/fix for this?
Thank you!
I have a customer with 12 x V1615 (Vodafones Branded Kaiser) all experiencing the same problem.
I should be getting my hands on a device on monday to test some stuff out on.
Mine did it a few times (Orange Tytn 2) but seems to have fixed itself now...
Hi all,
Just got my TyTNII yesterday to replace old O2 Zinc.
Everything was good, until i found out the button 5 (originally assigned for program camera) doesn't work.
I try to assign button 5 another program but it just doesn't work and when i reassigned button 6 for camera, button 6 works fine.
Everytime i press button 5, the response given is backlight will turn on, button 1 to 4 light will also turn on. but just that, the program assigned doesn't run.
I really don't hope to bring it to Service Center, as in my country, for PDA, even we claim in the same day we purchase, we won't get any replacement, and it will take one month (more) to return and sometimes just to let u know they didn't do anything. My previous O2 Zinc was also the second unit.
Help me please.
Keep it assigned to camera, but keep pressed a little longer to lunch the camera.
Hey I got my TyTN II yesterday, quite excited about the device. But I have the exact same issue. Did anyone else run into this problem? And any solutions for it, or should I ask for an exchange? Help please.
Ths button is a dual mode button for the camera. Light press to autofocus then deep press to fire.
If you re-assign it you need to press deeply to activate
Thanks for the reply, that was silly of me just figured it out.
Thanks for the reply.
This one's got me stumped, I may just be overlooking a simple answer but it hasn't happened previously on my Magician or Vario before.
I carry my Vario III around in a large coat pocket for most of the time. I have a lot of appointments and calls which activate the screen when they occur. I then have the problem when fishing around for the device that a) I answer the call from touching the screen, b) End the call from touching the screen, c) Open a load of different apps where the appointments have made the screen go live and the movement in the pocket has brushed the screen.
All I want to do is use only the hardware buttons ie. Answer, End, Power button. Where can I find the settings for this? The "key settings" menu or "buttons" doesn't cover it so where is it? It's driving me mad!
Hold down the 'red' phone button to lock all but 'Power' and 'Unlock' soft key.
You can still answer a call as normal when it comes in with the with the 'green' phone key.
Thanks. I know about the standard lock, but then you're into multi key press territory to unlock it. I just wondered if someone knew of a way (or program) that once the screen was off it stayed off until the answer, reject or power button was pressed and then in the case of the power button the device returns to "normal".
I'm not sure if your idea would be very viable. The screen has to come on so that you can see who's calling!
Pretty pointless to reject a call when you don't know who it is.
I understand what you are trying to get at but wouidn't you still have the problem of not being able to use any other functions within a call like looking up a Contact or checking your Calendar. Hitting the Power button during a call to get back to normal use would be a bit 'hit n miss'.
Thanks for the reply. I agree it's not ideal and I guess if it was something everyone wanted someone would have brought a .CAB out for it. That my Q answered in any case. Thanks again.
Try searching the forum for 'S2U2'. It might be what you're looking for.
That should cover it just fine. Thanks for the pointer.
Nice one helterskelter
Didn't think he would want to open it to answer a call thats all as he seems to have big fingers and hit everything but 'Answer'
No, sorry, just my dark humour...
Hope you are sorted.
Hey,
I recently received my G1 back from HTC after a repair, However I have realised that it has acquired a new problem since its return. For some reason if you press to hard on the 'Chin' or lower part of the phone where all of the function buttons are such as, Menu and call buttons, the screen will fade to black and will only re-appear on double pressing the end call button, however this doe not always fix the problem. This has become a problem when using the phone as it is very frustrating for the phone to go black and having to double press the end call button inevitably exiting the current application.
I'm reluctant to send it back as I do not want to wait and was wondering if this is a common problem or whether someone suggest something that I could do.
Many thanks