Caught in a loop! Please help! - Touch Diamond, MDA Compact IV General

My Sprint Diamond boots to the "Touch Diamond" screen, sits there for a while then resets, boots to the same screen, resets, etc. I've done a hard reset which appears to work but it resets and I end up back in the loop.
I have HARDSpl installed. I can get to the bootloader screen but I can't flash anything. I get 0% then the Error 262 no matter what I try to flash. I tried updated Roms, stock rom, etc. I ran through the Recovery steps several times with the same results. Always Error 262. I used MTTY and output shows two bad blocks when formatting then it says "Format Ended".
Does anyone have a suggestion I haven't tried?

Related

WM5-Device Will Not Load Operating System

I am having a problem that I hope someone can help me with.
I have an SX-66 with WM5 on it. The other day the device suddenly stopped booting. I can get the device to turn on, soft-reset, hard reset and get into bootloader mode, but whenever I try to boot the operating system it gets stuck on the colored stripe boot screen and just sits there showing the version numbers and nothing else. I have followed the instructions on the Wiki for downgrading but I still have the same problem. I have tried draining the battery fully and recharging but still no dice. I am even able to reflash the device with my laptop and it says it succeeds with the up/downgrade but then it just gets stuck again. If I try to install a 1.40 the device says that the flash is successful but then WM5 tries to boot again and I am stuck at the striped screen.
Can someone please help me out? Do I have a brick?

Stuck at HTC logo

Today I flashed my device to L26 KaiserDiamond from a WM6.1 Dutty's ROM.
The device rebooted fine, but when I tried to restore contacts/notes/etc.(via Sprite Backup), it performed the operation normally, but after restarting it is now stuck at the HTC logo.
I tried to reset the device via a hard reset, and it doesn't even get to the HTC logo... it just hangs at the L26 flash screen with the version numbers.
Is there anything else I can try, or do I have an excuse to buy an iPhone now?
Have you tried to re-flash it?
I'd put it in bootloader mode and re-flash.
good luck
try taking the battery out of your phone

stuck at white bootloader screen

after several times trying to unsuccessfully install a hard spl. (it installs and on reboot keeps the version 3) i upgraded the radio and now its stuck on the htc loadup sreen with the version listed on the bottom . a hard reset just resets so i cant even run the repair utility
one more thing
Oh and one more thing because it wont boot full or go into hard reset mode the computer will not recognize it.

Stuck in Bootloader screen

Hello all,
as the title says, one of my touch diamond's is stuck in bootloader screen.
I didnt do anything in between it working and not working, it was on my desk, put it there working, got it 5mins later, and it was in bootloader screen (tricolor screen).
What i've already done to try and fix it:
flash it with the original HTC rom, flash completes succesfully, phone reboots to tricolor screen, so no solution there.
install mtty and format the phone, this completes, reboot the phone, again goes to the bootloader.
reflash the phone with original rom after cleaning it with mtty, flash again completes succesfully but when it reboots after flashing it just goes to bootloader again.
Tried to flash a Hardspl: stuck at 0% and stays there. so that doesnt work.
BUT! when in mtty i give the "boot" command, it DOES start to boot WM. but then again, when i turn the phone of, and on again, or it reboots because of first start after flash, it goes to bootloader again. The VOLDOWN button is NOT stuck, cause when it boots i can use the vol buttons perfectly fine.
Anyone got an suggestion in how to unbrick it? i have a second, perfectly working diamond here too, if that helps in any way.
Some more info ive just seen in mtty, when i told it to boot, it said ONE BAD BLOCK IN CE, remove block ---- to ---- (dont know the exact numbers anymore)
hi..i had something like that...
just download this.
"RUU_Signed_1_93OliNex_HSPL_UnsignedEdition"
it's only 1.7MB and it's will make it work.. atleast it did the job for me...
Hi,
My T mobile touch diamond stuck in bootloader screen? Any experties to help me please.
Thanks in advance.

[Q] HTC sprint diamond will not boot past splash

Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
ryan21x5 said:
Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
Click to expand...
Click to collapse
If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
for official rom you can find at http://www.shipped-roms.com/index.php?category=windows mobile&model=Diamond

Categories

Resources