Hi,
When I pull my stylus - nothing happens... doesn't turn on or unlock device.
or during a call opens "notes".
Everything is Checked - it should do it, but it won't...
Any Ideas ???
Thanks
Take out the stylus, then remove the rear panel from your diamond. Look to see if the tiny magnet strip has become dislodged. This happened to mine after I'd had it just two days... it made it difficult to insert the stylus, and it just felt all wrong, because the strip had stuck itself in an awkward position. It also wouldn't recognize when the stylus was withdrawn.
I very nearly returned my diamond under warranty, until I looked closely at the stylus aperture and noticed this issue. I fixed it with a tiny spot of super glue on the magnetic strip and deft use of some plastic tweezers... saved days of re-programming a replacement.
Mr. Orange owes me a beer I reckon ;-)
Thanks for the reply...
The magnetic strip is there... I feel the magnet working...
but the diamond doesn't recognize when its in or out...
Anyone ?? Help - is it hardware or software ????
also a problem with the magnet strip
I own my diamond now for three weeks and something went wrong with the magnetstrip..it looks like it is still inplace but the magnetic force is stronger on the outside of the phone then on the inside (where its supposed to be) I'm trying to move te strip in the right position. but is not working.(seems like te strip is in the correct position)
It just happened. Really annoying..The phone goes on when I remove the stylus. (and the stylus is holding , but I don't get "the magnetic snap anymore"
Itay Shekel said:
Hi,
When I pull my stylus - nothing happens... doesn't turn on or unlock device.
or during a call opens "notes".
Everything is Checked - it should do it, but it won't...
Any Ideas ???
Thanks
Click to expand...
Click to collapse
shalom! go to:
settings/personal/phone/advanced (tab)/"when a call is connecting, open the Notes application when stylus is pulled out"
also in the diamond's manual
Hello all.
So, long story as short as possible:
My Tilt got run over, LCD screen was busted but I could still make and receive calls by sliding it open, hitting the call button and using the keyboard to dial and 'enter' to connect.
I was also still able to connect to the phone via bluetooth from my mac, as well as syncing it on my PC partition.
Eventually, I think I hit too many random buttons and turned the phone off or something as I could no longer get it to dial out this way. I was always getting the flashing green and blue lights though.
After some research (and un-won auctions on eBay) I decided to see if popping in a new LCD screen would fix my situation.
I installed the new LCD last night, and the machine is almost back to living, however, I now have the current problems:
When the phone boots into 'normal' mode, the screen is display is very truncated. It doesn't display the full HTC updated today screen and won't respond to touch. It says 'no service' but wi-fi seems to connect. If I slide it open, the keyboard lights up but doesn't respond, neither do the front keys. Also, I get only a solid orange light in the upper left LED.
If I boot the phone into 'Safe Mode' it responds to touch, connects to the AT&T network, connects to Wi-Fi, etc. The front keys still do not do anything, and when I slide it open the keyboard does not light up or respond. Also, I get both the green light in the upper right and blue in the upper left.
Another thing, when I slide the phone open and closed there's a slight ripple in the middle of the phone like something is 'pressing' on it from the back.
Sorry for the novel. Any help is appreciated. I'm considering 'clearing storage' and returning it to factory settings or flashing the ROM. I've taken it apart and put it together like four times now, checking, double checking and triple checking connections.
Thanks!
Sounds like one of the headers isnt fully seated in the display region. IIRC there are two that I had to deal with with my 10min LCD swap routine
Yeah, I think you're basically describing symptoms of having put the phone back together wrong except that it's interesting it responds in this 'Safe Mode' and interesting that it would happen after four retries
It's probably going to need a hard reset then! You might want to check nothing has been bent, warped mountings/plastic could be the cause of the screen ripple issue.
Were there any active components on the touch film for the display? (Assuming you have replaced that too with the LCD, or that they're one whole unit) if that is the case, they may be different, newer revisions? Really grasping at straws there though; at the end of the day, the poor phone has been mauled by a wheel... best of luck!!
Thanks for the thoughts! I guess I could try and break it down again. As far as I could tell, everything looked like the phone in the disassembly directions; nothing appeared unduly bent or mangled.
"Sounds like one of the headers isnt fully seated in the display region."
I'll google it, but what 'headers' are we talking about? The small metal bits that seem to touch the upper outside edge of the LCD screen?
Would an improperly seated header cause the other symptoms? Unresponsive other buttons (keyboard, front keys) and connectivity issues with the network?
"Were there any active components on the touch film for the display?"
I got a new LCD and digitizer (is that what you mean by other active components?).
Thanks again!!
AtillaDNun said:
Thanks for the thoughts! I guess I could try and break it down again. As far as I could tell, everything looked like the phone in the disassembly directions; nothing appeared unduly bent or mangled.
"Sounds like one of the headers isnt fully seated in the display region."
I'll google it, but what 'headers' are we talking about? The small metal bits that seem to touch the upper outside edge of the LCD screen?
Would an improperly seated header cause the other symptoms? Unresponsive other buttons (keyboard, front keys) and connectivity issues with the network?
"Were there any active components on the touch film for the display?"
I got a new LCD and digitizer (is that what you mean by other active components?).
Thanks again!!
Click to expand...
Click to collapse
Any cable that attaches to the circuit boards, re-seat every one you can find. One faulty connection can cause a lot of problems. I have a similar problem with a button on my PSP but im to lazy to fix it.
a couple weeks ago i cracked my screen. I bought a new one and replaced it myself. All was well until i tried to text with my physical keyboard and discovered that the i,m,n,k, and period keys were all unresponsive, these keys are also all in the same area.
I took apart my phone again and discovered that there is a thin strip that connects the keyboard to the unit. on this strip are 7-8 parallel lines running atop it(not touching). I noticed that the far right line had a break in it with a width much less than a needle head.
I don't know much about board circuitry but i think the lines are made of copper. I've voided my tilt warranty by opening up my phone so i'm here for suggestions. Are there general cell phone repair shops? Should i attempt to solder it myself? or is there no hope?
now concerning software my phone is out of control. When i try to message someone with the rest of my physical keys my phone will randomly insert enters and spaces into my typing which is really annoying and forces me to use a slow virtual keyboard. My phone screen will turn back on when i press the little side button, and when i have a call it will randomly put people on hold.
My phone will alos freeze up some times and an error message will popup with the option to dump some sort of file which i have to to continue. Is this some sort of virus on my phone?
I have the hyperdragon saphire rom with the radio that came with it. Do i just need to reflash? I apologize for the length of this thread all responses are appreciated.
as for the software craziness i'm sure you have tried the system restore(if you havent do it: shut off device, hold down the two 'blank buttons' and holding down the soft-reset button with the stylus at the same time then press the SEND button [green call button]) so since you probably have definitely reflash. My advice for repairing your phone is try to determine if the price for getting it repaired by a general repair shop or if repairing it yourself is better (because they might charge you who knows what )
For the sleep issue go to Settings/System/Key Lock and change it too 'Lock all buttons except power button'(mabye you did this). Also it is possible to have a virus on your phone although a system restore or reflash should fix this.
"I've voided my tilt warranty by opening up my phone so i'm here for suggestions"
actually... if u look at the phone the "warranty void" sticker is under the battery, not under the LCD. I cracked my LCD before and replaced it, after doing so, my SIM wouldnt register (phone took a heavy hit breaking the screen and sim slot). I figured what the hell and called AT&T and swapped it under warranty... They didnt say anything and I got a brand new Tilt back
I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?
Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?
I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim
when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers
Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?
Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?
iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!
Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here
Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff
mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.
try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?
you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")
thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work
Hello everybody!
To make a long story even longer I just got LCD replaced on my Acer Liquid E by a technician and the cable that makes touch keys on the bottom responsive (4 of them - Home, Search, Go Back, Menu) got damaged and now they don't work at all. All other functions are OK including camera button and + and - volume. Is there any way to reassign "camera" or "volume" button to be used as "home" or "go back" button ? Or is there an app that would allow you to get by without using those touch keys below the screen? If there is something that can be done would you please explain in great details cause I'm so damn it's scary.
Thanks a lot guys!
Not much help or advise from anybody to this point. But that is quite OK cause I happen to do some digging around and found solutions to my problems.One app is called Button Savior (Root). That's what the author says in the software description:
"Requires root
Requires USB Debugging enabled
If you are afraid of breaking your hardware keys or you have broken keys or you simply just don't have any key on your device, get Button Savior to make your life easier.
This app will display a floating software key panel which can be summoned everywhere anytime.
[Features]
(1) Simulates 'Home' 'Back' 'Search' 'Back' 'Recent Task' 'Screen Off'
(2) Can set to always open or auto hide based on user
customizable timer
(3) Two types of trigger action to choose from
(4) Added Camera key and Call key simulation
(5) Customizable trigger position"
Another one is called Soft Home for BarTender. And there are many more options available for similar problems.
Hi, I had your same exact problem! I replaced the screen by myself, and soft buttons stopped working. Since i didn't damage the cable, I'm 97% sure that the problem is the adhesive used to replace the old one. You need a special adhesive that "conducts" capacity (see h t t p : // focus.ti.com/lit/an/slaa379/slaa379.pdf at page 16).
When i tried to open the device again to replace the adhesive, I ruined a flat cable so now I have damaged the upper part of the touchscreen too, so I'm actually hoping to get it repaired under warranty without saying a word about what happened.
Fingers crossed!
I hope it worked for you my friend. Those Acers are nice phones till something goes wrong and you need to fix it. And Fido does not give a flying rat's ass if your phone is not on warranty. Their customer service just vanished over night the moment rogers took over. Very sad, it used to be awesome company to deal with. I got myself Galaxy S Captivate from AT&T, rooted and unlocked it and now using it on Fido.
Trying to replace the Display I didn't even noticed how I brake the flat cable of the AB88_A1__V1.1_Keypad_A_FPC. I have just received the Keypad Cable 50.H480W.005 from mk-electronic.de
Wish me luck putting my A1 device together.
Hello everybody!
I just bought a broken Acer S100, it had broken touchscreen (also the flat was broken) and there was no keypad. I mean, dismounting the phone, there was nothing related to the 4 buttons under the screen.
I just received the new new touchscreen, but still I don't have the keyboard. I read that dicer13 has bought the replacement flat, what I wanted to know is if the keypad is made only of 1 piece or if there are several pieces that are connected by the flat cable he bought.
IN few word, if I order the "50.H480W.005 Keypad cable" will I have everything to fix this phone or that's only a connecting flat between the mainboard and an other piece that goes just under the screen, which is missing?
On the other hand, will you suggest me to stop thinking about the phisical keypad and use, instead, the Buttun Saviour app? It is possible to use every normal function or the phone would be quite "limitated" and unconfortable to use?
Thank you very, very much for your answer!
nowhere is there an exact answer is whether or not it
dicer13 said:
Trying to replace the Display I didn't even noticed how I brake the flat cable of the AB88_A1__V1.1_Keypad_A_FPC. I have just received the Keypad Cable 50.H480W.005 from mk-electronic.de
Wish me luck putting my A1 device together.
Click to expand...
Click to collapse
Keypad Cable 50.H480W.005 does this piece? it is compatible with the model Acer s100? no photo as it looks..