Hello.
One xperia entered tricolor screen (volume down + powering on) but now it cannot leave that screen, even if the battery is taken out for a minute.
Is there a way to kick the xperia out of bootloader mode?
The screen shows this, in this order:
RUUNBH (aligned right)
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707 (these last 4, aligned left)
Upgrade ROM Code Error (centered)
Please try again (centered)
Serial (centered)
(and it says USB if connected, of course)
I tried the 'reset' button but of course that didn't help.
I tried hard reset and it showed it was hard reseting, but after that, the same tricolor screen appears.
I tried also RUU with hardspl, and RUU with ruu_signed.nbh (supposedly UK official rom).
In both cases it goes to withe screen with the progress bar at 0% but stays there until you take off batery, then it returns to previosly mentioned tri-color screen.
Thanks in advance. HELP please!
Hi mate can you explain which rom you have tried to flash?
sumitescp - do you know what I can do - I start with the hard spl process it all works well and then it stops at the mulivolour sreen and I get an error message !
Hi
had the same prob, simply pulled the battery
Worked
Cheers
H
Didn't work for me...
hungarian said:
had the same prob, simply pulled the battery
Worked
Click to expand...
Click to collapse
It didn't work for me. I pulled the battery for 2 mins, nothing.
1 hours, nothing. 24 hours, nothing... it still turns on to the tricolor screen.
I let the battery die completely... then recharged it, and same result.
I think I need the proper ROM
where did you get your phone ?
Related
Hi,
I have a k-jam and I was trying to update it to the custom ROM. it hanged at 98% and the update software crashed on my PC so I had nothing to do but soft resetting the device.
Now I cant restore to the original imate ROM and when I try to go to the USB mode it gives the colored screen and goes off immediately.
Please help...
hey i have had that problem stuck for 2 days, must be stressing eh?
hold camera + voice then push reset button for 3 seconds...keep holding the cam and voice button and wait for the screen to come on..then plug in.... usb shud show on bottom left..
i had that problem....couldnt get it to boot loader but after numerious tries, it worked.
It just needed some power
Wizard was totally discharged i recharged it and restored the ROM successfully
thank u
I'm trying to run an upgrade on a tmobile device, I believe it to be cid unlocked as I've been running the Kjam rom on it for the past few months. It is a G3 device.
When I connect the device to the pc it connects with active sync, I start to go through the upgrade to another rom process answer the questions no problem, the device then goes to a black screen and after a few seconds I get the warning cannot communicate with device.
I have tried different ROMs including ones with no ipl spl, I have tried doing a soft reset whilst holding the two buttons, each time the same result - black screen.
I recover from the black screen by removeing and replaceing the battery.
The battery is fully charged.
fully charge battery, go into bootloader (hold camera button + press reset with pencil) try and do this CID unlock procedure again
Hi guys,
Just as a preamble, I have read and attempted the stickied tutorials regarding HardSPL and Flashing ROM. During each attempt I have encountered problems.
When trying to HardSPL, using the standard method, I was not able to successfully complete the update. The phone would go as far as the progress bar, and just stop and sit there at 0%. I left the phone for over 20 minutes without any indication of success. The HardSPL program will go to a fail and ask me to step-by-step restart the process.
I was, however, able to successfully up date the phone by using HardSPL, and booting the phone with the Vol- & Power pressed down. Now, when I boot the phone, the Vol- & Power method shows
Code:
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
If I use the HardSPL to enter the bootloader, it shows
Code:
KOVS110 MFG
SPL-0.52.0liNex
MicroP1-787
MicroP2-707
I found this odd. In the system information shows that the phone was updated to R3A011, it was R3A010.
Anyways, now when I go to flash the ROM, using the SD method, it goes as far as the grey loading screen, and sits there and does nothing. I've tried multiple different ROMs, thinking the ROM was the problem, but nothing changes.
I just tried HardSPL again, and now it says there is an update to 1.9.0, should I do it the same way I did above, or no? What is wrong here? Why don't roms load in the bootloader?
Thanks in advance.
Adam
Hard-SPL is not applyed to your phone
If it does not want to work with the standard method, try this one:
-stop your phone
-Vol Down + start buttons to start the phone in tricolor mode
-connect USB cable from your PC
-run X1_HardSPL.exe
-follow the instructions
I bought an X1 from second hand with a cooked ROM. I then tried to flash another ROM with RUU. It stucks in 34% then error appeared. Following with RUU's recovery instuction, it got same problem in 39%.
I then tried to flash hard-SPL again with succeed. However, the phone reboots then stucks in the SE Bootloader Screen and can not be turned on again.
I found a strange problem which I couldn't even enter to the tri-color bootloader screen when my phone handed on.
(my phone is Sony Ericsson X1i)
Thanks in advance.
I can't even hard-reset my phone.
I am waiting for my battery charged upto 100%. Hopes it work.
seasonlau said:
I bought an X1 from second hand with a cooked ROM. I then tried to flash another ROM with RUU. It stucks in 34% then error appeared. Following with RUU's recovery instuction, it got same problem in 39%.
I then tried to flash hard-SPL again with succeed. However, the phone reboots then stucks in the SE Bootloader Screen and can not be turned on again.
I found a strange problem which I couldn't even enter to the tri-color bootloader screen when my phone handed on.
(my phone is Sony Ericsson X1i)
Thanks in advance.
Click to expand...
Click to collapse
it can't be turned on because there is no OS installed on your phone now, take your sd card out and place an rom image renamed to kovsimg.nbh in the root of your sd card through te pc. put it back in your phone, just start and it will enter bootloader again, and (if everything gone as it should be) it will open kovsimg.nbh, press power button, and wait
Thank you for replying my post.
But the problem is I can't even enter to tri-color screen by holding volume down and power.
Any advice? Thanks.
seasonlau said:
Thank you for replying my post.
But the problem is I can't even enter to tri-color screen by holding volume down and power.
Any advice? Thanks.
Click to expand...
Click to collapse
what does your phone do now when you start it then?
It stucks in the SE Bootloader screen.
seasonlau said:
It stucks in the SE Bootloader screen.
Click to expand...
Click to collapse
I misunderstood you, tri-colour screen is the bootloader/SPL.
Your stuck on the SE logo booting screen..
I'm very sorry, but i really have no idea, how you could fix that..
If you can't get in the tri-colour screen, then there is nothing you can do.
sorry
maybe someone else can help you
Thanks for prompt reply.
But do you think X1 require 100% fully charged battery to enter the tri-color bootloader?
no it doesnt need to be 100% charged
What happens when you connect your x1 through usb with the computer?
Does your pc recognize the x1?
same problem, x1a dead , the pc recognize "Microsoft USB Sync",
If you've already Hard-SPL'd your device, chances are if your device gets recognized as Microsoft USB Sync (Even if activesync won't start) you can use the ruu_update tool to send the rom to your phone. This process (if successful) will automatically boot you into the tri-color screen approx 2-3 minutes in.
Hope this helps, and Good luck
For advice or help on flashing roms, please post your query in this thread
Thread closed
Hey everyone,
I just installed a keyboard on my HTC TD2 and when I powered my phone back up it froze. It does not get past the "Touch Diamond 2" screen.
I have tried powering it up by holding the volume keys and the power button but that just gives me an error that says "Step 2 Error: There is no enough battery in the machine."
I also tried powering up by holding the Talk/Send key + End key + Power button and a screen just pops up with a picture of a harddrive and above it it says "Downloading"
Any help?
R&R the battery, then let it charge for a few hours, then try a hard reset.
Bruce Inman said:
R&R the battery, then let it charge for a few hours, then try a hard reset.
Click to expand...
Click to collapse
Tried it. Now the battery error doesn't show anymore and instead I get a different one:
Step 3 error while updating:
File operate: File does not exist.
Restart the machine?
(Green bar on bottom with teh word yes on it but I can't press it.)
:-X
I also just tried the hard reset after taking out the microSD and this time the screen reads:
"Check if there is a valid image"
And then it switches to"
"Step 3 error while updating:
Card operate : read retry timeout.
Restart the machine?"
(Green bar on bottom with teh word yes on it but I can't press it.)
I also tried formatting the microSD and starting/booting the phone with the microSD in it. Got the same step 3 error.
Weird that a keyboard installation would cause that...
If you are unable to hard reset, I would put a ROM .nbh file in the root of your SD card and try to flash from bootlaoder mode.
Thats the error you're getting, its looking for the .nbh file to load.
anyone find a solution for the above
i am Trying to turn my t5388i but i am not getting past through the HTC Diamond boot screen
any solution for the same
batalia said:
i am Trying to turn my t5388i but i am not getting past through the HTC Diamond boot screen
any solution for the same
Click to expand...
Click to collapse
Your's is a clone, you need to ask in this thread.