Setting GPRS, no connection - Tilt, TyTN II, MDA Vario III General

Hello, ive been trying to set the GPRS setting for my kaiser but had no luck , it always shows that it doesnt get any connection. Could someone tell me were to write for everything to work? Here are my operators settings:
profile name: TELE2 GPRS
start page: http://wap.tele2.lt
IP adress (WAP GW IP): 130.244.196.090
authentification: normal
connection type: permanent
data bearer: GPRS
APN: wap.tele2.lt
port: 9201 or 8080*
ID: -
Password: -

So could someone help me?

Related

Using ATT iPhone SIM on Kaiser email problem

I am having a problem reading my POP3 email.
The Kaiser configured itself to ATT (with the iPhone SIM) and the connection appears as MEdia Net
Connection to the Internet (Explorer) Works OK and I get the H connection. I am in Los Angeles.
However when attempting to read my email (Shows 3G) I get a "cannot connect with current connection setting" and gives me the option of going to Connections settings Where I get MediaNet or My Work Network. (It is set to go to MediaNet I believe)
I know the POP3 settings are correct as they work great via WiFi.
Any suggestions?
Thanks
yes change medianet to My Isp wap.cingular settings and everything will be fine.
the settings are:
wap.cingular
username: WAP.CINGULARGPRS.COM
password: cingular1
THANK YOU.
My ISP connection was auto set by the Kaiser to
isp.cingular
username: ISP.CINGULARGPRS.COM
Per your suggestion I changed ISP to WAP and all seems well
Thanks again

T-Mobile Tzones Connection DEAD!

Cellular (GPRS)
-Access Point Name: wap.voicestream.com
-Proxy server: 216.155.165.50
-HTTP should be 216.155.165.50 port 8080
-WAP should be 216.155.165.50 port 9201
-Secure WAP should be 216.155.165.50 port 9203
Those are the connection I'm using right now. It use to work, all of a sudden, when I connect to internet explorer, this pops up
HTTP ERROR: $CODE$
$MESSAGE$
REQUEST URI=/M
still working for me. reset and all that jazz
chucknasty626 said:
Cellular (GPRS)
-Access Point Name: wap.voicestream.com
-Proxy server: 216.155.165.50
-HTTP should be 216.155.165.50 port 8080
-WAP should be 216.155.165.50 port 9201
-Secure WAP should be 216.155.165.50 port 9203
Those are the connection I'm using right now. It use to work, all of a sudden, when I connect to internet explorer, this pops up
HTTP ERROR: $CODE$
$MESSAGE$
REQUEST URI=/M
Click to expand...
Click to collapse
try port number 8080 for wap and secure and socks ip is the same but port 1080 and mine never fails.
still doesn't work
Similar issue
I am having a similar issue with my Dash. I am using the tmobile proxy and I get the HTTP ERROR: $CODE$ $MESSAGE$ REQUEST URI=/ error when I installed Palringo. Once I installed Palringo I started getting the error in PIE, but Palringo worked fine. I uninstalled Palringo and I PIE works again.
Also, I get this error when I attempt to share the tmobile proxy with my pc. They connect and show everything working, but when I attempt to go to anything in a browser on my pc I get the HTTP ERROR: $CODE$ $MESSAGE$ REQUEST URI=/ error in the browser on my pc. I can still browse on my Dash, but it will not share this connection with my pc.
I can ping domains from my pc and it resolves the domain but will not get any response from the pings.
It seems to me like tmobile has some sort of restriction on their proxy that is causing this. Any ideas?
I've been having the same problem. I've drove to another location to rule out tower, tried other tmobile branded phones, noted other co-workers having the same problem, which ruled out sim card, hard reset my phone, and flashed back to factory rom. The only think I've noticed is if I flash to factory rom or do a hard reset and keep the cooked rom, I do NOT get the error until I install any program... doesn't matter what the program is... but after installing it the first time the error starts again.
It doesn't happen ALL the time, but will happen at least once on every connection.
I'm actually on the phone with Level 3 support at T-Mobile now to see if they can solve the problem. I'll let you guys know what I find.

WiFi and GPRS conflict on my Tytn II I need Help

I am no longer able to connect to the Internet via my home WiFi network. I am able to WiFi connect to the network without any problems, but when I try to use any application that accesses the Internet the phone looks for a GRPS connection. I do not have a data account attached to my sim as I live in Australia, and as far as that sort of thing go, we are a backwater…
The WiFi connection and access was previously working fine until I tried to disable the GPRS from trying to connect, as this would routinely bring up messages informing me that a GPRS connection could not be made. I do not know what settings I have changed but I cannot seem to reverse the situation.
I have soft reset a number of times, I have re-run the connection wizard, etc my current settings are as follows:
WiFi:
Wireless
Configure Wireless Networks –
.MyWirelessNetwork Connected
Configure Wireless Network-
Network Name: MyWirelessNetwork
Connects By: The Internet
This is a hidden network: unchecked
Configure Wireless Authentication-
Authentication: Open
Data Encryption: WEP
The Key is Automatically Provided: unchecked
Network Key: **********
Key Index: 1
Configure Network Authentication-
Use IEEE 802.1x network access control: unchecked
EAP type: Blank
NetWork Adapters
My network card connects to: The Internet
Connections:
Tasks
Vodafone Internet Settings
General-
Vodafone Internet Settings
Modem-
Name: Vodafone Internet
Number: vfinternet.au
VodafoneInternet
Enter a name for the connection: Vodafone Internet
Select a Modem: Cellular Line (GPRS, 3G)
* no user name or password, because I don't have the service
Proxy Settings-
The network connects to the internet: checked
This network uses a proxy server to connect to the internet: unchecked
My Work Network
No connections have been set up here
Advanced
Select Networks
Programs that automatically connect to the Internet should connect using: Vodafone Internet Settings
Programs that automatically connect to a Private network should connect using: My Work Network
GPRS Settings:
PAP authentication
I do not know if this is all the info need to sort this out, but any advice would be greatly appreciated. I have done allot of customising and I really don't want to have to a Hard Reset. I can connect through all applications, if I am connected by USB.
Thanks
First you need to make sure your connection is set to use My Work Network as first priority. Next you need to make sure that the WiFi connection connects to WORK NOT the INTERNET. probably your problem, did the same thing on my 8125
Cannot access hidden Wifi / Non-broadcasting SSID with the HTC TyTn II Kaiser
KDKobes said:
First you need to make sure your connection is set to use My Work Network as first priority. Next you need to make sure that the WiFi connection connects to WORK NOT the INTERNET. probably your problem, did the same thing on my 8125
Click to expand...
Click to collapse
Hi there,
Can someone please help by advising me on how to overcome this problem.
If I broadcast my SSID, the device connects fine, but when I stop broadcasting, the device will show that the network is unavailable. I did check the "This is a hidden network" checkbox option, in the settings.
Configure Wireless Network-
Network Name: MyWirelessNetwork
Connects By: Work
This is a hidden network: CHECKED
Configure Wireless Authentication-
Authentication: Open
Data Encryption: WPA2-PSK
The Key is Automatically Provided: unchecked
Network Key: **********
Key Index: 1
Please help,... many thanks!
Kind regards,
JonD
My device is the HTC TyTn II (Kaiser) running Windows Mobile 6 Professional

Interesting Question

I don't know that anyone would know the answer to this but I thought I would try anyway.
I have a tilt but I also have an iphone. I have pretty much fallen in love with my tilt all over again and would like to know if anyone knows of a way to surf the web on my tilt using my iphone data plan. All answers point to no when I took a look at ATT's website but I thought maybe one of you guys knew of a work around.
Cant you connect up using bluetooth and surf the web that way? Seems pointless when you can just browse the web on the iphone though.
Edit: nvm I just realised what you were saying. Just shove your sim in the tilt and use same settings as on your iphone. Can't see why that wouldnt work unless it sends a signal to your carrier saying what model phone you are using.
I could but I was thinking more for when I am on the move and don't have a bluetooth or wifi connection to connect to.
This would be for when i am at random places where I just don't have an alternative way of connecting.
Could this work? Pinched it from a blackberry site though. Can't test, since i'm not in the US.
Code:
Name: MEdia Net
Homepage: http://device.home
Service Type 1: WAP
Gateway IP: 66.209.11.61
Port 1: 9201
Domain 1: Blank
Service Type 2: WAP
Gateway IP 2: 000.000.000.000
Port 2: 9201
Domain 2: blank
DNS 1: 000.000.000.000
DNS 2: 000.000.000.000
Timeout: 15 minutes.
CSD No 1: 14152441012 or 18472549271
Username: [email protected] (required for CSD use only)
Password CINGULAR1 (required for CSD use only)
Speed (Bps) 1: 9600
Linetype 1: ISDN
CSD 2: Blank
Username 2: Blank
Password 2: Blank
Speed (Bps): 9600
Line Type 2: ISDN
GPRS APN: wap.cingular
Username: <leave blank>
Password: <leave blank>

[Q] WAP APN for android

As I know, android doesnt support WAP APN.
Does any body know can I configure APN to connect with WAP APN?
Maybe there is possible to write sth?
Reasone for this question: my mobile net. give access to some services only threw WAP protocol :/

Categories

Resources