This has been bugging me for months and it's about time that i ask...
Under power setting, the lowest you can the device to turn off is 40sec. Is there a way to edit this so it turns off in like 5/10/20/ect seconds? I'm searching the registry but I couldnt find the right key to edit. Any help would be appreciated.
Related
Hi Everyone. I was hoping someone might be able to help me with something. I'm looking for a way to assign a different key on my AT&T tilt as the power button. Basically I would like to have the end key act as the power button when it is pressed down and held for a few seconds. I've been searching all the Kaiser threads the last couple days. And I've found several threads that start to mention the topic, but I'm still not clear on it. The best solution looked to be AE button plus...but then I saw in another thread that it doesn't work for the power button. So, if this kind of question has already been answered, I apologize...I just couldn't find it.
So, can anyone either push me in the right direction, or give me some pointers on the best way to search for this info on the site? I really appreciate it.
Thanks!!!
The power key is connected directly to the mainboard so as far as i'm aware there is no way to assign a different button to power.
However there may be a way to assign the end call key to turn the phone off only, but it wouldn't be able to turn it back on unless you use the power key.
I'll have a look now.
AE Button Plus would work for turning it off, it does have that option. However, you would still need to use the regular power button to turn it back on.
My tilt's EDGE and 3G connection automatically turn on, sometimes when i wake up, it's on for 9 hours, why is that? and i can't find a way to fix it. And when i put the tilt away for a few min, the screen will automatically shut down to save on energy, and i will have to press the POWER button once to have the screen back up. Can we change this setting? it is not very handy. thanks for the help. i am a noob.
NODATA:
http://www.modaco.com/content/pocket-pc-software/246171/new-free-utility/
Power settings:
Start/Settings/System/Backlight
arnoo said:
NODATA:
http://www.modaco.com/content/pocket-pc-software/246171/new-free-utility/
Power settings:
Start/Settings/System/Backlight
Click to expand...
Click to collapse
Thanks for the msg so quick. the power setting u mentioned only can adjust the mins longer or shorter before the screen turned off. but it didn't adjust the way turn back on the screen. I really don't like to press the POWER button. is there a way to change it. thanks
Start/Settings/System/Key Lock
....
read this: http://forum.xda-developers.com/showthread.php?t=347438
vicdeng said:
My tilt's EDGE and 3G connection automatically turn on, sometimes when i wake up, it's on for 9 hours, why is that? and i can't find a way to fix it. And when i put the tilt away for a few min, the screen will automatically shut down to save on energy, and i will have to press the POWER button once to have the screen back up. Can we change this setting? it is not very handy. thanks for the help. i am a noob.
Click to expand...
Click to collapse
I had the same problem,
Disabled push email.
Problem went away.
I have a similar problem. Is there a way to see what application is opening the data connection. I had email set to download once a day, so it was not my email. Can't think what else it may be...
Hi,
Is there any way to change backlight time out when the phone is locked(long red button press)??? Normally my phone is set up to turn of backlight after 40 sec -and I wanna KEEP it. I need to shorten that time to 5 sec only when the phone is locked(when accidentally I press any button in the pocket it will be unnecessary draining battery for 40 sec. Please can anybody help me?
Bump, I would like a solution to this also. Seems like my Diamond used to time out after ten seconds when locked, but it doesn't do that anymore. Now it uses the settings in the Setting:System/Power/Backlight, which I have set at 45 seconds I believe. I think installing Phone Alarm might have something to do with it. I disabled Phone Alarms power settings, but still same problem.
Anyone know the fix for this?
Nevermind, I just started using S2U2, and I can adjust this the way I need it. Thanks.
Hey guys, I just flashed the latest -G- ROM and then put tf3d on it. I made sure to install the touch power and standby .cab's as well. My after about one or two minutes being idle keeps turning the screen on and off and there is no way to make the problem stop other than doing a soft reset with the stylus. Is there a way to fix this problem?
Also I tryed plyaing with touch power but I don't seem to fully understand this program. I hit the power button and it shuts down tf3d as expected but when I hit reload tf3d 90% of the time nothing happens. Is there a way to jus make the power button work as it did before (when u lightly pressed the power button the screen turned off, long press it shut down the phone).
Thank you guys for your help, I searched and I'm sorry if this question has already been answered before.
If you actually read the included README then you would have seen this
README said:
(Note:You MUST disable TF3D on the today screen and allowing the device to go into sleep after a set amount of
time. Go to Settings/System/Power.)
Click to expand...
Click to collapse
readings hard, i from ky it's crazy how many NEW THREADS get started to ask A PERSONAL QUESTION instead of asking in the THREAD WHERE YOU GOT THE ROM!!!
no actually he asked in that thread and he also made this thread
Im sorry for the not reading the read me file, in my standby cab zip package there wasnt a read me and neither was there one for the touch power package. I tried following your advice but my kaiser doesn't seem to want to go to sleep automatically even when I have adjusted the settings to do so. I even uninstalled touch power and standby and it still won't automatically shut off the back light and sleep. Do you or anyone else know what else I can possibly do other than a hard reset?
streetrideF1 said:
Im sorry for the not reading the read me file, in my standby cab zip package there wasnt a read me and neither was there one for the touch power package. I tried following your advice but my kaiser doesn't seem to want to go to sleep automatically even when I have adjusted the settings to do so. I even uninstalled touch power and standby and it still won't automatically shut off the back light and sleep. Do you or anyone else know what else I can possibly do other than a hard reset?
Click to expand...
Click to collapse
have you tried utop's standby program?
umm...."Touch Power" msd?
kaiserII101 said:
umm...."Touch Power" msd?
Click to expand...
Click to collapse
umm....was thinking he was possibly confusing that with the earlier tf3d standby aps, kaiser
Hello all,
When making a call the screen dims WAY too fast then turns of in 10 seconds. is there an option to leave it on all the time, till I decide to turn it off?
It's quite the pain in the A** when I need to enter numbers like when I recently had to activate my XP COA by phone..PHEWW what a nightmare.
The other problem I have is randomly I realize the volume for both are on off..
I dont know how this happens and if I'm to blame but sometimes it happens even if I dont use the phone to make calls I realize the off button is pressed..
Any way to remove the speaker button totally? I wouldn't mind doing it in the settings area..
anyone
can anyone help me?
backlight settings
hi m8, click>start>setting>system, then you should see backlight click this and it gives you the backlight settings if on battery power or external power, hope this helps
regards
timbo2272