Related
Is there a way to format the PDA and reinstall a ROM. My PH20B1 is started to freeze after a ROM is installed and at Complete on the Setup for minutes. I end up just soft-resting cause after mins past its not doing anything....Is there a way to fix that???
Isn't it supposed to be like that? You're supposed to reset after the ROM upgrade shows 100% complete.
I think I understand the problem you have from the limited information supplied.
You have rebooted to a white screen after a failed rom upgrade, correct?
If so, just disconnect your device from the PC, hold power+record buttons, then prod the reset hole with your stylus. You will see "Serial v2.xx" where "xx" can vary. Now attach the phone to your PC (device now shows "USB" instead of "serial").
Next, kill off all activesync processes on the PC (ctrl-alt-del to enter task manager, then end task on "rapimgr.exe", "wcescomm.exe", "wcesmgr.exe").
Now that the device is attached and activesync is killed, start the ROM upgrader application to update the phone ROM.
After successful upgrade, it often helps to reboot the PC as well as the phone, as activesync does not always recover well from having its processes killed.
Im saying that My PDA is starting to freeze. Even after running, its starting to freeze up and I have to soft reset it. I am able to install a ROM on it however at the end of installing the ROM where the screens says COMPLETE...Tap to continue ro begin using your device...and its starts the ROM....As soon as I tap the screen in the middle of starting WM5 it freezes... Ive even downgrade to Wm2oo3SE and it still freezes. But after soft resest there was a message about "system data is corrupted, System will erase all data to fix this error! Yes or No to fix"....Can that be fix or am I able to re-format the PDA hdd and reinstall WM2oo3SE or WM5?
Hi again,
This is a guess, so treat it as such, but I suspect that something in your extended ROM could be causing the problem. On first boot after reflash, a file "autorun.exe" is executed from the extended ROM, and this will normally install a bunch of CAB files.
If something in your extended ROM was corrupt or otherwise not correct, it could cause a lockup on first boot - immediately after calibrating the screen, setting the timezone etc, just as you describe.
The safest thing to do is to revert to the device's complete set of original ROMs, as found in this table :-
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
The original ROM-set will restore the main ROM, extended ROM and radio ROM to the defaults.
If the problem is fixed afterwards, and you still feel brave enough to upgrade to WM5, then first repartition your device so that the extended ROM is empty. Instructions on how to do this from within WM2003 are found here :-
http://forum.xda-developers.com/viewtopic.php?t=50628
Figured Out A Solution
I figured out the problem and Im not sure if others have experienced this problem or not. Even if you dont created an extended rom on your Blue Angel when changing from rom to rom, if your screen tends to freezes after saying "tap on your screen to begin using your device" you will have to run the DOC repartitioning tool in the Prepartion Folder of some ROMS. Once running the program as the directions tells you and preform a reset even a hard reset on your device, everything will run fine without freezing.
hello couple weeks ago i found htc s730 in Norway but the phone have password
when i turn it on it says :
Password
denne enheten er last. Skviv inn enhetspassordet, og klikker du meny> Avbryt fot du slar nummeret.
My question is : is it possible to "unlock it" or mayby i have to install new ROM?
thanks for all your help
You found the phone just laying around? The owner who lost the phone probably locked it.
I would do a hard reset of it to wipe the data and start over. If theres any information you can see or use on it to return it to the person missing it that would be good. Otherwise hard reset and enjoy.
yes i found it on sidewalk with empty battery and without any simcard
ok. but i have no idea how to do this.
can somebody tell me how to do the hard reset s730 ?
thanx 4 all ya comments
...
Everything works fine
restart to the factory settings hepls awesome.
thank U once again
Cant do hard reset ..
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..
The sequence of pushing and holding down is key to success:
1.) switch off
2.) push and hold l+r softkey
3.) switch on (no long push, just normal - but keep L+R pushed)
4.) wait for the prompt for reset
5.) release keys
6.) follow instructions on screen (could be "press 0 to ...")
QHelmer said:
i have the same problem..
not that i have found a phone but that it has pasword on it and they person who has the phone cant remember the password..
we would loove to do the hard reset.. but it doesnt work..
holding down the two soft buttons and then holding down power button for 1 sec.. it does nothing at all...
anyway else to do it ?
remeber,, i cant get into the menus due to the password..
Click to expand...
Click to collapse
HTC Wings S730 Soft reset
Restarting your Phone
Restart your phone when a program is not performing properly or the phone is not responding to any keypresses.
To restart the phone
1.Remove the battery.
2.Wait for three seconds, then reinsert the battery and turn on your phone.
WARNING! If the phone is restarted while a program is running, unsaved work will be lost.
HTC Wings S730 Hard reset
Press and hold both soft buttons + press POWER button for 1 sec.
Resetting your Phone
Resetting your phone will remove all the data from its memory and restore the phone back to the factory default settings.
Important If Encrypt files placed on storage cards is or was enabled before, then backup all files from the storage card before using Clear Storage, performing a hard reset, or updating the ROM system software. Otherwise you will no longer be able to access the encrypted files on the storage card. Use ActiveSync or Windows Mobile Device Center to transfer files between your storage card and computer. After the procedure, copy your files back to the storage card.
WARNING! All your data will be deleted, it is recommended that you back up your data first before resetting your phone.
To reset your phone
1.Click Start > Expert > Clear Storage.
2.Follow the on-screen instructions to reset the phone. The phone will restart after it has been reset.
thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..
Then the softkeys seem not to work ok. They are used very often and usually are the first to quit their duty. They will not work in the applications later as well, so possibly this is the reason why it was lost.
Another idea (not sure if THAT works): slide out the qwerty-keyboard and use these softkeys for the excercise, maybe that works?
A definite way to come to a hard reset is to put a new ROM on the phone. It will however only work if the phone is either CID unlocked (permanently with SuperCID or temporarily with GoldCard) or you have the original CID matching ROM update at hand.
Go to http://www.shipped-roms.com/index.php?category=windows mobile&model=Wings and pick one that fits.
Then perform a normal upgrade. If that is not possible due to the locked phone, put it in bootloader mode first:
- push and hold camera key
- switch on or insert USB cable
-> you should see 3 colour screen
From there you can start the ROM Update.
QHelmer said:
thank you Tobbie and Hakim Rahman for trying to help..
but it doesnt work..
it just boots the phone.. then asks for the security code for the phone..
Click to expand...
Click to collapse
I think you need upgrade SPL to HardSPL...
This look at the Threads of Jockyw2001 :
Wings SSPL and HardSPL
--------------------------------------------------------------------------------
The attached SSPL and HardSPL are based on the Wings MFG SPL v0.91
- download the attached files
- REMOVE SIM and SD CARDS !!
- connect usb cable
- create a SPL backup by running spl-backup.bat from SPL-backup-kit (make sure you Wings is "application unlocked", run the attached SDA_ApplicationUnlock on PC)
- copy sspl-0.91-wings.exe to your device and run it
- after a few seconds "USB" appears on the display
- unplug and replug the usb cable
- if you only want to test the sspl try flashing the attached splash screen by running CustomRUU.exe from flash-splash-wings
- you can now flash the hardspl-0.91-wings.nbh by running CustomRUU.exe from flash-hardspl-wings
- after installing the uspl or hardspl you can flash any rom, cooked rom, radio or splash screen
Note:
The HardSPL is never overwritten which in case of flashing trouble is a great insurance. Should you want to flash another SPL or USPL you must run the SSPL.
Features:
SuperCID / Security Level=0
Does not check NBH signatures
Based on 0.91 MFG bootloader, rtask, fat2sd, sd2fat enabled
Accept any password
Model ID check only 4 chars
SPL overwrite DISABLED (to bypass, use sspl-0.91-wings.exe)
Bypasses "Task 2A" (this formats entire flash which renders your Wings into a brick, we don't want that)
Important:
Use at your own risk! I'm not responsible for any damage to your device caused by using the attached files
Hi Hakim Raman,
...the suggested procedure will not work as you must have access to the device first for application unlock and executing applications. This is only an optional procedure if the poor guy wants to play with custom ROMs later. One step after the other...
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Exa777 said:
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Click to expand...
Click to collapse
Try to reflash the rom you was flashing in the first place.
Mayb it is locked, cause it needs a serten file from that rom.
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
ted presley said:
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
Click to expand...
Click to collapse
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Exa777 said:
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Click to expand...
Click to collapse
try agent47´s task29 that might help
Im trying atm...so far its been 10mins and its stucked at 0%....i cant flash anything =(
Edit... it Gave me update Error 262
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
I Hope this help you!
In one occasion I suffered a similar problem and the issue was that the Memory Card was damaged, and when the Phone Start and tried to read this it "stuck" reading this.
Try to start the phone without the memory to see if this work.
Regards.
Musse_1 said:
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
Click to expand...
Click to collapse
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Exa777 said:
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Click to expand...
Click to collapse
I've had it.... here is the list of everything i've tried
Mtty /Task 14 0 , Task 28 55aa , task 8
Flashing SD Method
Flashing Stock Rom /Sd Method
Flashing Another Stock rom /SD method
Flashing HardSPl back and for from stock to olinex 72
Using Seus Updater
Take out battery out of the phone for 24h+ to (reset it)
Used Task 29...with no sucess...
Flashing using Cuu Firmware or whatever its called....failed
Every single time i try to flash it goes wrong ... for stock roms it stop at the OS part
Anyways Seus updater put me on spl78..but fails when it comes to the OS @(15%) Like
I just need to Fail Flash one of the Stock rom to go back to spl 0.72
my question is is there any hacked/cooked rom wich include HardSPL like the stock roms does?...that would like flash my bootloader?
Any other suggestion would be greatly appreciated...i dont wanna throw my Xperia Away..when it still can boot in bootloader...i refuse to believe X1's Bricks that easily (ONLY 1 BAD FLASH )
Phones current situation: has no OS, Cant charge it , it turns on itself whenever the USB is plugged in
HardSpl wont flash whatever what i try...so im stucked on Stock SPL eitheir 72 or 78 ..that i can still choose
Phones MicroSD methods keep saying OS fail , (0018003)
Likewise with stock Roms
Mtty...didn't do ****!!!! yet it i got the log like if went trough alot and ****....
lolSEUS Updater get stuck at 15% after updating the bootloader.
Help?
I have unfortunately bricked my phone, had put custom roms on my phone before and had itje's Touch 14.2 on my phone for about 6 months before deciding to change it.
After changing it, the phone would update to the rom i wanted, but then after about 6 hrs of rom use, the phone would stall, hang and require a hard reset, after trying with a number of roms, this became the norm. I was therefore trying to get my touch 14.2 rom back, but managed to brick my phone.
The phone starts in bootloader mode with:
"KOVS110
SPL - 0.72.0000
MicroP1-787
MicroP2-707
Contunue to Upgrade ROM, please wait...
USB"
That is with the phone connected to the usb port either charging, or connected to the computer (with the sim card out), when the sim card is in, it changed to
"loading..."
and stays on that screen.
I have d'loaded mtty, signed the drivers, but not sure what iam doing wrong..
Possible steps I may need to change for mtty to correct itself maybe due to these factors in this thread (http://forum.xda-developers.com/showthread.php?t=540290&highlight=serial)
MysticGenius said:
Follow this procedure for FLASHING YOUR ROM FROM INTERNAL STORAGE AFTER MTTY
Before you start grab: mtty1.42.zip
AND ENSURE YOU HAVE HARD-SPL ON YOU DEVICE!!
Procedure:
1: Download a ROM of your Choice, RENAME the *.nbh for your ROM to: DIAMIMG.nbh
2: Copy DIAMIMG.nbh to the "Internal Storage" of your Device.
.
Click to expand...
Click to collapse
* Phone needs to be in Hard SPL mode (not sure if the phone is in that mode anymore)
* Place *.nbh on the internal storage of the device (I cannot do this, as the phone is not recognised by the computer)
I have tried everything, but to no avail...
Hard resets, re-flashing, mtty....all come back to the same screen
Please help... : (
try this
try flashing a stock rom and then flash a cooked one...
i had the same problem on my x1...when i flashed a new rom it was fine till i make a soft reset...but instead of a soft reset it performed a hardreset...and sometimes hang on the SE logo
hope it works
report back
I fixed it!!!....
Used SEUS to update the ROM...
phew!!!..
now to hard spl my phone...again
task 29 will also un-brick your device, trying to reflash will give an error, but task29 will set you back to the beginning
Mod. edit: not dev related, moved to general
glad you managed