Database Develop

I Think I just Bricked my AT&T Tilt

Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks

Be strong. I think it's only bricked when you can't power it on.
I have a poor net connection and not time atm. So a suggestion if you haven't already, search the forum for the word bricked. I'm sure this has happened before..
There are several tricks that people know so you might be ok. good luck.

Calihoe said:
Uhh......yea......I was trying to upgrade my Rom to Dutty's Diamond V1 Build 19588. I was using the instructions from Flash-Your-Tilt . I got to Step 4 CID-Unlock it installed 100% rebooted and then nothing. Now the phone will only play the intro with no sound, then go black. It shows in the lower right hand R 1.70.02iNex, G25.65.30, D1.62.00.00. The phone will allow me to do a hard reset but after it it goes through the intro with screen alignment and installs the extra apps, it reboots and then goes black. I did a ton of reading through the wiki's if someone could point me in the right direction or tell me if its toast, it would be much appreciated.
Thanks
Click to expand...
Click to collapse
Flash an OEM Rom/Radio Combo. Also it wont hurt if you already CID unlocked to to go ahead and flash a new SPL to it. Should fix any and all issues as your phone is still actually booting and Not bricked

Installing windows the 6.1 ROM from HTC's site worked. Thank you very much for the great advice. If I wanted to now put Dutty's ROM on my phone can I go straight to that, or do I need to restart the whole ROM flashing process(installing Jump SPL, Hard SPL and CID) ?

If you have unlocked it, just put duttys onto the SD card and rename the .nbh to KAISIMG.nbh
Put the phone into bootloader and install Its the fastest most successful method. No worry about a data cable coming out mid flash ( happened once to me....not fun )
Shouldnt have to install hardspl again ( or use JumpSPL )
Just make sure that if you are installing a WM6.0 rom that you have a WM6.0 radio. If not, the flashing process for the radio is the same ( rename to KAISIMG.nbh )

Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.

Calihoe said:
Is there a way to see if I the hard SPL install and CID unlock worked ? Can I just restart the whole process regardless. Sorry for the noob questions.
Click to expand...
Click to collapse
Go into bootloader. If your screen says hardspl somewhere near the top then you're good to go. Check which version because you can have radio problems if you use a WM6.0 spl with a WM6.1 rom. Most recent roms are WM6.1 so try HardSPL 3.29 or higher.
If you don't have hardspl, get it here for wm6.0 roms or here for wm6.1 roms.

many thanks, your advice with the links were invaluable. I read and read and read, but i guess i did not read enough. This site rocks.

New Official ROM Upgrade- Release Date: 2009-04-14

I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23

Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks

Ht845kh14923 :d

o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.

Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??

Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??

It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???

Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!

Could anyone check, if the gps-support has been improved?
km

lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?

lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??

Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725

GPS seems to work fine now, also the scroll behavior of opera is better
km

It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint

Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?

Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.

Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please

nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom

Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel

jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer

Urgent help pls. "Loading" screen on

OK. Decided to upload a new ROM as my phone was getting slow and unusable.
It's an O2 XDA (Touch Diamond) with:
Touchflo v3 Build 29946
ROM 1.93.206.6 WWE
09/08/08
Radio 1.00.25.05
Protocol 52.29.25.12H
Boot R1.00.25.05
I downloaded Olinex's unsigned developer Hard SPL and I extracted the NBH file and renamed it DIAMIMG.NBH following the advice here:
http://forum.xda-developers.com/showpost.php?p=2707841&postcount=4035
On soft reset I pushed the vol down and back buttons to get the boot loader stripes, then let go.
I now have a screen which says "Loading..." and has done for 20 minutes. I have now got the phone on charge while I wait for some help to see what to do next, just in case this is a critical stage - don't want to brick it.
Reading through again I am concerned that this was a procedure for rom upgrade not Hard SPL install, can someone tell me please?
Thanks in advance for any help.

Well, I ended up taking the battery off to get it to reboot. It seems to boot fine back into the old ROM.
I still intend to upgrade it (to SwiftBL's v7.5) but have a few questions:
1. Can the HardSPL be run from the internal storage card? If so is it simply running the exe from the unpacked zip from within a folder? ActiveSync is a bit too flaky for me.
2. Do I need the SIM card in the phone at any stage of the ROM upgrade?
3. On the original ROM I get a drop down menu to setup the phone to the UK O2 network settings. If I load a new ROM, will I need to know these settings?
Cheers

1. HardSPL cannot be run from storage. Only Activesync or Bootloader
2. No. You can flash without SIM card
3. You can use connection setup on any new ROM. Usually starts straight after initial setup.

OK here's where I'm at now.
Downloaded jockyw2001's HardSPL 1.24
Ran it and it got as far as prompting me to run on the phone. I said 'Yes' and the HTC screen went black as expected.
Next stage was to run the DiamondCustomRUU.exe file which I did but this is waiting for ActiveSync. ActiveSync will not sync with the phone now, I guess because the phone is not 'on'?
Where do I go from here?

Use the Hard-SPL in my sig with your RUU.

Thanks, will do (it's not the one mentioned in the ROM author's description though).
So how do I recover the phone from the black screen now? Is it safe to remove the battery to reset?

Battery pulled after reading this post:
http://forum.xda-developers.com/archive/index.php/t-427945.html
I'll try the SPL you mentioned now.....

Had a good search but can't find out. This Olinex zip contains just one file RUU_Signed.nbh.
Where do I get the other files from to run this?

use the attached . It has the RUU exe and the nbh.

Thanks. This is a signed version I see, was going to use SwiftBL's ROM which requires unsigned.
May take a look at other roms that use signed unless you think that I can load the SwiftBL rom with this version?

Potentially Broken T.HD - Need help!

Hi All,
I have used the search function - but ended up getting confused.
I have a Touch HD that I bought in January of this year (2009) from Mobiles.co.uk (Carphone Warehouse) and is on the O2 network (UK).
I have been using Dutty's ROMs (both 6.1 and 6.5) for months now - and have always used USPL when flashing, using the SD card method.
Over the past 3 days, my HD has been playing up.
When it started, I was using Dutty's R7. The radio was 1.14.something.something. The device was working perfectly, and I was really happy with the ROM and the way the phone was working. I had installed NO other applications with the exception of a different taskbar and obviously SDKCerts.cab
First of all, HTC Sense stopped working - it would cycle between "Loading HTC Sense" and "Tap here to launch HTC Sense"
Then, when rebooting the device, it just hung on the "Smart Mobility" screen. I left it in case it just needed a while to boot, but nothing.
I had no other option than to hard reset.
It worked OK for a few hours, but then HTC Sense started to crash again. So I flashed a new ROM - Lost in Asia or whatever it is called.
Same symptoms.
I flashed Dutty's R7 back and also the new 1.17 radio.
No joy.
The phone also hangs for ages on the Smart Mobility screen - perhaps a full minute where as before, it used to be no more than 15 seconds or so.
The following is displayed on the "Smart Mobility Screen"
1.17.25.09
52.69.25.37H
1.59.Dutty
The bootloader screen (before running USPL) shows the following:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) V6
So the question I'm asking - is... Is my phone suffering some kind of hardware malfunction, or is this a known and fixable fault that I somehow have caused?
If the phone looks like it is malfunctioning, how would I go about returning it to stock so that the CPWH repair centre do not know it's had an unofficial ROM installed?
I'd like to add that whilst I'm very PC literate, I'm no programmer and a lot of the stuff here is alien to me hence my confusion - I just know how to flash a new ROM etc.
Thanks to anyone that takes the time to help me - I'd be really thankful to anyone that helps me sort this - be it tell me how to fix the device, or tells me to take it back!
Thanks in advance & Regards,
Chris.

Will D/L and flash Dutty's R0 Holy Grail ROM and see if that makes a difference...

If you've been using uspl than it will still be the stock spl and thus you could try to load the stock rom from htc.com specially designed for the touch hd(blackstone). I've read and heard from a lot of people that after flashing several roms and even hard resetting afterwards, some bits and pieces stay behind and flashing an original stock rom will undo this. I don't think it's a radio issue. And another big thing if you use dutty R7 that's a 1.56+ rom so you should have the right uspl olinex software to load these roms, if you used older software then problems with colouring and other things will appear.

a1gp said:
If you've been using uspl than it will still be the stock spl and thus you could try to load the stock rom from htc.com specially designed for the touch hd(blackstone). I've read and heard from a lot of people that after flashing several roms and even hard resetting afterwards, some bits and pieces stay behind and flashing an original stock rom will undo this. I don't think it's a radio issue. And another big thing if you use dutty R7 that's a 1.56+ rom so you should have the right uspl olinex software to load these roms, if you used older software then problems with colouring and other things will appear.
Click to expand...
Click to collapse
Thanks for the quick reply.
So is it perhaps better to revert to the original ROM before flashing a cooked ROM? I always Hard Reset twice after flashing as understand this helps.
OK - so the 1.56+ situation - I was under the impression that using the latest USPL (2.5) when flashing was OK? I have never had the colour problem... but perhaps if I'm flashing wrong then these problems could be to do with this?
Thanks again...
Chris

The Sense Manila has known bug that you need to press home to load it (sometimes).
For you case, I would suggest you to clean up your SD Card.
there may be several file that cause your system to freeze.
So, format your SD, hard reset.. and cross fingers.

Yes, It is better to revert to the original rom once in a while before flashing a new rom, if u used the latest uspl and the colours are ok, then you've done that right and it will probably be bits and pieces of old flashed roms floating around on the device.
Best to revert to stock rom and hard reset twice.
Afterwards flash the rom u want. If everything works again. U could hspl instead of uspl, hspl is more stable if u ask me. And you can go back to stock spl if you have waranty issues. there's a tut on that to in the rom section.

mcdull said:
The Sense Manila has known bug that you need to press home to load it (sometimes).
For you case, I would suggest you to clean up your SD Card.
there may be several file that cause your system to freeze.
So, format your SD, hard reset.. and cross fingers.
Click to expand...
Click to collapse
I forgot to mention - that was one of the things I did. Previously, I had loads of email folders from all the ROM installs.
Now I have a folder containing the useful CAB files that I need, and the ROM image file. Thats it.
It's only a 1gb card as my 8gb card gave up the ghost.
Thanks for the suggestion though and my apologies for not mentioning this in the initial post.
From reading the Dummies guide, am I right in thinking that in order to use a 1.55+ ROM (such as Dutty's Holy Grail R0) I only need to run USPL and then flash (as opposed to flash a newer SPL) as my stock SPL is already 1.54?

a1gp said:
Yes, It is better to revert to the original rom once in a while before flashing a new rom, if u used the latest uspl and the colours are ok, then you've done that right and it will probably be bits and pieces of old flashed roms floating around on the device.
Best to revert to stock rom and hard reset twice.
Afterwards flash the rom u want. If everything works again. U could hspl instead of uspl, hspl is more stable if u ask me. And you can go back to stock spl if you have waranty issues. there's a tut on that to in the rom section.
Click to expand...
Click to collapse
Thanks for this - I didnt realise the device would retain bits and bobs, and you may well be right in that things are getting corrupted in there!
Which is the best stock ROM to flash - is there a link to one? I looked on the Wiki and there seem to be loads... which will work on a UK T8282?!
Thanks again!
Chris

constablechris said:
I forgot to mention - that was one of the things I did. Previously, I had loads of email folders from all the ROM installs.
Now I have a folder containing the useful CAB files that I need, and the ROM image file. Thats it.
It's only a 1gb card as my 8gb card gave up the ghost.
Thanks for the suggestion though and my apologies for not mentioning this in the initial post.
From reading the Dummies guide, am I right in thinking that in order to use a 1.55+ ROM (such as Dutty's Holy Grail R0) I only need to run USPL and then flash (as opposed to flash a newer SPL) as my stock SPL is already 1.54?
Click to expand...
Click to collapse
what do you mean hang for age?
1 minute is nothing if it turns out boot up.
There are chances that the nand flash needs to refresh and wasted some times. But it won't be forever.

constablechris said:
Thanks for this - I didnt realise the device would retain bits and bobs, and you may well be right in that things are getting corrupted in there!
Which is the best stock ROM to flash - is there a link to one? I looked on the Wiki and there seem to be loads... which will work on a UK T8282?!
Thanks again!
Chris
Click to expand...
Click to collapse
there's an original rom on htc.com for blackstone just use that one.
hope it will turn out right for you

I thought I'm the only one who had this problem. Last Sunday my blackstone started to freeze on the smart mobility screen too. I flash 3 different roms because I thought its an rom issue with no luck. On Monday it even managed to hardreset itself after I waited for about 15 min in the smart mobility screen.
After that I flashed a stock rom and it seem to be fine by now.
But now I will flash a custom again, the stock one is so 6.1

[SOD] Any Solutions? Task29 for Topaz Included

There's a lot of beautiful ROMS for our device but most of the new ones face one problem SOD (Sleep of Death) when the device goes to sleep you can't wake it up.
What "causes" SOD?:
* Bad Flashes
* Residual code for flashing you device a lot
* Newer SYS cooked in ROM
I've been searching for a solution and this is what I've found.
qbus00 said:
That's something which I have to do...
I'll downgrade SYS to 21896 soon which does not face SOD problem.
Click to expand...
Click to collapse
wuub said:
MTTY is a software that allows you to format internal storage before you flash a new rom.
By doing this you will make sure that no residual files or past informations are kept in the system. This usually fixes random crashes and weird behaviours on PDAs.
This is the DIAM100 thread but i've been using on D2 without trouble : http://forum.xda-developers.com/showthread.php?t=540290
Click to expand...
Click to collapse
From HD2 ROM Thread
rjd1 said:
I started having issues similar to this and a few other non-normal issues with NRG ROM. I ended up loading carrier ROM again, re-flashing 2.08 radio and then 23544 COokie ROM and all cleared up. It appears alot of risidual code happens with the HD2 ROMS regardless of AS or SD card ROM loading. I added to my flashing every 2 weeks or so - I am a flashaholic...
Click to expand...
Click to collapse
doloop said:
Hi,
(To make it short, follow the red sentence to format your phone to avoid roms problem.)
I hex-edited RomUpdateUtility.exe so it runs task 29 right after flashing ruu_signed.nbh
Task 29 formats your phone memory (=binfs). It prevents weird error appearance when you flash new Roms.
you stile need something to flash, it may be a radio, a splashscreen nbh or a blank nbh file (shadrack repack provide a tiny blank nbh).
Usually you don't need anything more than the file provided in the packs. so:
Just unzip and run task29.exe .
Eventually, you may replace ruu_signed.nbh with the radio/splashscreen of your choice.
When update status reach 99%, press vol down button, and keep it pressed until the phone reboot to the three color bootloader.
After the phone reset itself, your old rom will be gone, so it can't boot to winmo: binfs has been formated, your phone memory is clean.
if you fail to press vol down key and your phone get stuck on the white screen, just remove your battery, then try again: press power, and keep vol down pressed immediatly next, until the phone get to RVB bootloader.
When your phone is back to RVB bootloader screen, use the leocustomruu.exe provided with your favorite rom package to flash a new rom, or flash it from memory card using standard procedure.
Repack by ShaDrac (Recommended):
http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19
No radio needed, smaller, faster.
Video tutorial by [★]
http://forum.xda-developers.com/showthread.php?t=621930 (Video 9: How To Perform A Task 29 Without MTTY)
direct link: http://www.youtube.com/watch?v=DtTDuc4V4cU
To do:
remove the "reset" command from task29.exe, to stay into boot loader screen. Then, one should flash the new rom immediatly using their cook's flash utility.
Original files
http://www.megaupload.com/?d=J3OELQ8I
RS mirror, by Sardelisp
http://www.rapidshare.com/files/361617741/Radio_2.08.50.05___task29.zip
Edit, distribute, repack, comment and spread these files as much as you want.
Click to expand...
Click to collapse
I've tried some of these suggestions, but none work. I tried Task29 flashing a boot screen and everything was erased. I flashed a new ROM and guess what? SOD even with task29
If you want to try any of these procedures do it "At your own risk" task29 for Topaz will flash a custom boot screen and erase your WinMo.
Use it at your own risk
And you, got any solutions that want to share?
PS. I'm sorry for my english, remember I'm El Toro not "The Bull"

I have an ATT Pure and have flashed every ROM on here that is in English and not once has one failed to boot or contiunue running till I get tired of it. You do have to use HARDSPL with all of them. My only ROM issue are the ROMS that have everything in the Start menu instead of separate folders. It seems so disorganized but that is a different topic.
I just wanted to point out it must be your phone or you have not used hardSPL or maybe your phone vendor bugged it so you can't flash a new ROM.
Oh I also noticed you say it's and ATT thats unlocked. That could be the issue. Mine is not unlocked. BTW being unlocked would mean it is not an ATT unit any more right?

Solarenemy68 said:
I have an ATT Pure and have flashed every ROM on here that is in English and not once has one failed to boot or contiunue running till I get tired of it. You do have to use HARDSPL with all of them. My only ROM issue are the ROMS that have everything in the Start menu instead of separate folders. It seems so disorganized but that is a different topic.
I just wanted to point out it must be your phone or you have not used hardSPL or maybe your phone vendor bugged it so you can't flash a new ROM.
Oh I also noticed you say it's and ATT thats unlocked. That could be the issue. Mine is not unlocked. BTW being unlocked would mean it is not an ATT unit any more right?
Click to expand...
Click to collapse
Thanks for replying, my pure is Hardspl'd with the latest 2.51 Olinex. It's unlocked meaning Sim Unlocked that I could use it with any Operator that uses a Sim Card, and yes I could flash every single ROM that it's posted in this Topaz ROM Development thread. I've been using Dutty WWE Official Test ROM since he posted it and no problems have come up at all. The "new ROMS" are the ones that caused the SOD even our chefs have suffered from this bug. So it's not the device.

I never had the SOD happen to me. And i have htc pure too.

Apparently, the great majority of us do not have this problem, and have never heard of it. As long as MTTY is run, I've never heard of anyone having a sleep of death issue.
eltoro said:
There's a lot of beautiful ROMS for our device but most of the new ones face one problem SOD (Standby of Death) when the device goes to sleep you can't wake it up.
What "causes" SOD?:
* Bad Flashes
* Residual code for flashing you device a lot
* Newer SYS cooked in ROM
I've been searching for a solution and this is what I've found.
From HD2 ROM Thread
I've tried some of these suggestions, but none work. I tried Task29 flashing a boot screen and everything was erase. I flashed a new ROM and guess what? SOD even with task29
Qbus13 Com2 ROM with SYS downgraded doesn't face SOD.
If you want to try any of these procedures do it "At your own risk" Keep in mind that HD2 task29 files are intended for that specific device not for the Topaz I put them here just for reference, If you want to try the task29 for Topaz I could post it here, It will flash a custom boot screen and erase your WinMo.
And you, got any solutions that want to share?
PS. I'm sorry for my english, remember I'm El Toro not "The Bull"
Click to expand...
Click to collapse

Standby?
I've ran a few Rom's here from energy 6.5.5 to Dutty R6 - R10
with the latest 6.5.x builds, every once in a while after coming back from standby the device will be unresponsive. The touch screen seems to not do anything, but the hardware keys work fine, typically placing it back to sleep and waking it up again seemed to fix it... I have had to pull the battery once.
This didn't happen on the 6.5 builds, only 6.5.5.
Mostly running Energy Aprl and May releases.

I had SOD. I've solved it by changing my SIM card since previous one was more than 10 years old. With new one I never had this problem.

I'm using NhatHoa TopazRom 23563 WWE so far no SOD after 2 days of using it.

I flashed the Dutty's Topaz Sense 2.5 Holy Grail R10 |WWE| rom last night and get my phone goes into the SOD pretty much every time I leave it alone for more than 10 minutes. I have an HTC Pure as well. From the searches I've done it seems solving this problem is pretty much a turkey shoot. I just wish there was a concrete solution, as I kind of like being able to use my phone.

reptiletim said:
I flashed the Dutty's Topaz Sense 2.5 Holy Grail R10 |WWE| rom last night and get my phone goes into the SOD pretty much every time I leave it alone for more than 10 minutes. I have an HTC Pure as well. From the searches I've done it seems solving this problem is pretty much a turkey shoot. I just wish there was a concrete solution, as I kind of like being able to use my phone.
Click to expand...
Click to collapse
The same thing happened to me with that ROM but if you flash Dutty's Topaz Holy Grail R11 WWE it's fine no SOD

On the Touch Pro 2, Tilt 2 section they have a lot of theories about what causes SOD http://forum.xda-developers.com/showthread.php?t=648134
but still no solutions.......
They said that Task29 is the solution but is not I'm posting the Task29 files if you want to try it yourself
INSTRUCTIONS:
Originally Posted by SacTilt
Some of you are making this too difficult. I've posted this before, as this is all that needs to be done. Task29 does not remove your radio or your splash screen. It only clears the ROM, therefore, all you need to do is run Task29 and then flash your ROM. This is how I do it from the PC.
Connect to PC via Active Sync/WMDC.
Execute Task 29.
When phone boots to "Touch Pro 2" screen (or whatever your splash screen happens to be), I hold down the volume down button while hitting the reset button.
Once I'm on the Bootloader screen, and it shows "USB", I flash the new ROM from the PC as I normally would.
When the phone vibrates, indicating the ROM upgrade is complete, I disconnect the phone from the computer.
Click to expand...
Click to collapse
Of course in this case will be your Topaz, Pure, Touch Diamond 2 boot screen
CREDIT:
all credit goes to doloop
Originally Posted by doloop
Hi,
I hex edited RomUpdateUtility.exe so it runs task 29 right after flashing ruu_signed.nbh
As every one understand this command format the rom,
Just unzip and run task29.exe . You may replace ruu_signed.nbh with the radio of your choice.
After the phone reset itself, your old rom will be gone, so it won't boot: binfs has been formated, your phone memory is clean.
You'll need to power up in bootloader mode (press vol down right after power key), then use the leocustomruu.exe provided with your favorite rom package, or flash it from memory card using standard procedure.
Click to expand...
Click to collapse
This files are for Topaz only it will replace your Boot screen or if you want to replace it with another boot screen or radio is up to you. I like the boot screen because the process is faster. **Use it at your own risk**