My camera led light just started acting funny an hour ago. It turned on and it si now impossible to turn the damn thing off. It still stays on when the phone is turned off. I've tried removing the battery and then put it back again. As soon as the battery is in, the light turns on again. I've tried a soft reset and ultimately a hard reset. Light remains on.
Don't want to have to go to Sony for this because I bought the phone off the bay a month ago and therefore don't have a receipt so it won't fall under warranty. Anyone have any ideas? What a pisser.
hi,same here
I think its a hardware issue where the cables have been short and are giving direct connection. I dont know if this will work but try to tap the phone a little hard on your palm. If its just a loose contact it might get sorted. This is a very crude way.
You guys want help or just venting air?
Great story.... so ?!
If you guys want venting off air, that was it! If you are looking for help however, then KINDLY state some info, like:
what the frak is the phone model, firmware, recently flashed, if so to what. Branded or unbranded, built date, etc.!
After that, perhaps a few answers can be expected
MichaeltheImage: I doubt that in this case this had anything to do with software because of the fact that it remained on after a boot or when the phone is off.
Moleculez: Yesterday it ended up fading by itself after 2 or 3 hours. This morning it started again as I removed the battery. Tapped the led side of the phone on my palm a few times; and it worked. Thanks.
"Anything mechanical, give it a good bash."
Incase someone is still looking for a way to fix this problem:
I managed to pry the plastic covering off of the camera lense/ LED with a needle.
All it took was a slight nudge on the LED cluster to reposition it. It was situated slightly off to one side, causing the short circuit which lead to the LED being constantly lit.
Problem is, in my initial frustration I poked the LED and broke it which, as a result of the short, meant that although the LED was no longer lit it still drew power from the battery.
The only way I know that the later fix worked was by using a power consumption monitoring tool to verify that the LED (and the short circuit) was no longer drawing power.
Awesome.
Related
Yesterday I was texting someone, didnt even finish the message because something else demanded my attention. So I close the keyboard and put it in my pocket.
5 minutes later I take my phone out, and its off. I try to turn it on but nothing happens. Tried taking out the battery and SIM, waiting a few minutes, and put them back in, still nothing. I take it up to T-mobile and they tell me its a month out of warranty.
So earlier today, I say "ehh what the hell" so I try again, this time I held the power down for about 10 seconds, while its connected to a charger, and it boots up! I get past the G1 screen to the Cyanogenized boot screen (5.0.7 test 5 if it helps...) and in excitement I call someone in to show them. As I pick up the phone to show them, the usb cable is yanked out, and the screen goes black. Never felt ****tier. Tried to get it to power on again....back to square 1.
About an hour or two later, I look over and the face keys and keyboard are backlit, but still nothing on the screen. I also noticed that if I take the battery out while its off the charger, the backlight for the buttons will turn off, but will immediately come back on once the battery goes back in.
Basically, Im stumped, and any help would be appreciated.
EDIT: Now the button backlight is off...
I think your phone didn't shut off actually.
Try the 3 finger solute!
Hold send, end, and the menu button.
I've also had this happen to me, and to tell you the truth it didn't turn out good. :/
After awhile My touch went completely out.
It happened when I was running an experimental rom.
Also try restoring a back up if you created one before it started happening. :/
Well I know its off, Ive taken the battery out, and havent gotten it to come back on except for the one time. And Ive removed the battery since then as well. Ive tried power+home, power+camera, power+menu+send. None of them have worked.
One of two things, hopefully the first:
1.) You have a bad battery, replace it, or borrow a friend's and see if that works.
2.) You have a new paperweight. In that case, my condolences, friend.
Seriously, though, from what you described, it sounds like your battery just bit it. Try taking it out and examining it for any bulging or swelling that may not have been there before.
The woman at the T-mobile store tested a different battery and a different charger, so in my case its not likely, but I will give it another shot, since things have somewhat perked up. Right now the button backlights will randomly come on and stay on for a while, slowly dimming, and then eventually turn off, only to come back on later.
thegreatcity said:
The woman at the T-mobile store tested a different battery and a different charger, so in my case its not likely, but I will give it another shot, since things have somewhat perked up. Right now the button backlights will randomly come on and stay on for a while, slowly dimming, and then eventually turn off, only to come back on later.
Click to expand...
Click to collapse
After reading you tried different batteries, I think you're in the market for a new phone. =[
The battery idea was the only thing I could have thought of as well.
Hope you manage to figure this out without having to buy a new phone, though. =[
In regards to your most recent post, sounds like some kind of short. There wasn't any water exposure was there? I've actually heard of people having there phones in their jeans pocket and sweating enough to turn the indicator and fry the board.
But yeah, it sounds like phone death. I would totally disassemble it and check for any corrosion though. Who knows, you may save it, then you have fat bragging rights
Ninjineer said:
In regards to your most recent post, sounds like some kind of short. There wasn't any water exposure was there? I've actually heard of people having there phones in their jeans pocket and sweating enough to turn the indicator and fry the board.
Click to expand...
Click to collapse
They must be doing some serious running.... or be really, really fat.
Btw, you can check to see if your G1 got exposed to water, OP. Take out battery and there's a little sticker under the IMEI sticker. Its round. If it's white - you're good. Any other color (i think it turns red or blue?) there's water damage.
Here's what is going on...
My Galaxy S I9000 (Bell Canada) was water damaged, after being dried for many days it turned on, but the battery almost immediately drained. I left the phone and forgot about it. Bought a new cheap phone without a SIM.
More recently I got a new battery for it and it turned on and was working great, staying charged and everything. When I went to the service provider to get a new SIM for it, we powered down the phone, pulled the battery and SIM card and put the new SIM in followed by the battery. Afterwards the phone would not power on, but the two face buttons on either side of the 'Home' button lit up and would react to touch. I tried removing the battery and SIM a few times and would get the same result.
After bringing my phone home and leaving it with the battery out for a few days, I thought I would try it again. It powered up again as if nothing was wrong. To test it again, I pulled the battery and SIM, replaced them, and my black screen/won't turn on problem returned.
Every so often it will power on and be useable. It is recognized by Kies, I've flashed it to firmware 2.3.4.
I'm looking for any helpful suggestions for what might solve my problem. I'm wondering if it's a hardware problem and short of isolating the part of the phone that is faulty and replacing it, the phone is toast.
Thanks for your time, and I apologize for the length of my post.
My friend has dropped the SGS into a pool before. Problem was fix after buying a new battery.
Either: Damaged screen + Contact. Or the reaction with water and the battery. hydrogen gas prevents screen from connecting to main-board.
It still turns on occasionally, and when it powers up, it's as if nothing is wrong. Screen works, displays everything fine, colour is crisp, screen reacts to touch. The big problem is it won't turn on all the time. Would what you said still explain this?
tacotbone said:
It still turns on occasionally, and when it powers up, it's as if nothing is wrong. Screen works, displays everything fine, colour is crisp, screen reacts to touch. The big problem is it won't turn on all the time. Would what you said still explain this?
Click to expand...
Click to collapse
The only thing I know (assuming the screen or motherboard is 100% functioning) is hydrogen gas being present. You might know TV remote with old battery casually respond to presses. After cleaning contacts it should work again.
I disassembled the phone and cleaned all the contacts on the main board with rubbing alcohol, I did not do anything to the screen though. Should I try taking it apart again and breaking it down further? (ie. separate the screen?)
tacotbone said:
I disassembled the phone and cleaned all the contacts on the main board with rubbing alcohol, I did not do anything to the screen though. Should I try taking it apart again and breaking it down further? (ie. separate the screen?)
Click to expand...
Click to collapse
No, I am starting to think it's a hardware fault if that didn't work
So I recently cracked the screen on my HTC One m7. I bought a replacement screen and front housing. The screen was so far beyond repair that I couldn't shut off the phone prior to starting the replacement. I tried waiting for the phone to die but after two days I became impatient and did it anyway (essentially the phone lost power when I disconnected the battery). After transferring all parts into the new housing and being what I though as diligent putting all parts and connections back in their place, tried to power the phone back on. all that happens is that the back and home buttons flash and then I hear what sounds like the audio for when the phone powers on. The screen stays black and then phone doesn't technically turn on. I know this because I have missed messages and the green led light would be flashing if it was. Therefore, at this point I'm not certain that the new screen works or if I've connected it right. I've tried the numerous boot tricks with the volume buttons, nadda. I have had the phone on a charger for a full day and the same problems. (Disclaimer: I don't have the original charger, but I have been using this one for a long time). I do see the red charging led if I wiggle the charger in the input, but also just recently I saw a green led when doing this, which when the phone was working was a sign that it was fully charged. If anyone has a solution to my problem that would be great. I'm also interested on what's wrong, why this is happening, what might have caused this behavior? What do the flashing home and back buttons mean?
Howdy,
I've had the same problem, but my phone was shutdown allready. When I replaced the front screen, the phone won't boot. I would like to know if its anyway to get the files from sdcard down?
Thanks for the support!
So, one year ago, my C6602 felt on the water, for my bad, some of the waterproof doors were open. At first, it didnt damaged it at all, so i managed to turn it off, and wait cause we have a person who fix eletronic things. But, i was stupid. Even knowing that this would damage the phone, i did turned it on again...at first it were ok. One hour later, touch stoped working, couldnt turn the alarm clock off...then the screen goes off as well. Well, i did take it to stores who are specialized in cellphones and all of them told my cell was dead. Today, i decided to open it to see what the **** was happening, it turns out that i couldnt figure nothing out by myself, buttt i put the charger and got a red light. I though, its dead already, nothing bad will happen heeh. I let it for 4hrs~ charging, pressed the on buttom, but nothing happened, oh, at first, when i charged it a little, when i press the on/off buttom it would gave me 3 red notifications blinking, but that time it didnt. Instead, it went to green, and i could manage to access the cellphone on the computer (internal memory), all my files were there. Also, when chargin, it first showed me a red light, followed by a yellow/blank light, and, therefore, a green.
There is any chances that the cellphone isn't dead? Its this sorta of protection of your data what happened? Or the screen is really broken (and, by changing it, it'll be back to normal)? Thanks.
It seems that phone is turning on, but displays nothing. It may be display fault, but may be display related pcb malfunction also.
Hi all,
Last weekend I tried to fix the GPS on my Xperia Z (C6603) - it couldn't lock any satellite and according to all tests it was a hardware problem. When I opened the back cover I saw that the GPS antenna wasn't securely attached anymore (thanks to the third party who replaced my screen last summer I guess). While I was at it, I also wanted to check the speaker since the volume is generally quite low. Doing so I had some difficulty getting the battery out but it didn't look like anything was damaged by it.
I fixed the GPS antenna and reassembled the phone, but now it won't boot anymore...
When I try to boot it the LED blinks red three times and then stops. Nothing more. It only seldomly responds to a cold reset (vol up + power for 10 sec.) but mostly not. When I connect it to the wall socket or laptop the LED burns red continuously.
When I opened the phone I still had about 70% battery left so that should be fine. Nevertheless I've had it on a charger overnight (LED continuously red) and tried the next morning without success.
What I have found is that the red LED indicates either a broken bootloader or a hardware fault. Since it occurred after I opened the phone I would assume the latter.
I have managed to do a repair through the PC Companion software but without result. I can still get the phone in fastboot (LED turns blue) connected to my laptop to flash. The screen doesn't turn on, though I'm not sure if it should? I'm also not sure if being able to connect in fastboot excludes hardware failure?
I haven't tried to root/flash because I first want to ask for some advice on a more systematic approach to fixing it. Also, tonight I will pick up a friend's Xperia Z with a broken screen for spare parts (same model, he got it one month later). So except for the screen I have working replacement parts. Besides the screen replacement (with original Sony parts) the phone was still in original state both in hard- and software.
I would really like to fix the phone since I liked it and I'm stuck to a SIM-only plan until December still. Third-party repair is out of the question because of costs; then I'd rather spend it on a new XZ5.
Any ideas on how I should approach this?
After some trial and error, I have managed to flash a stock ROM (.253) on it. No luck with that unfortunately. When I try to turn it on, there is a small vibration after a few seconds and that's it. Again the phone responds to a cold reset, but when I try to boot it after the LED blinks red three times again. That's all it does.
I would say the only thing to still try now is swapping the motherboard with the other phone, not? Or are there any other suggestions?
Well, I would assume that it is a hardware problem, especially taking in to the account that you touched components inside.
Even if we all know how phone work, and where are all components are, its not recommended to touch anything inside if you dont have steady hand and environment to make any repair(clean place, no humidity, clean hands).
One bad plugged connector can brick your phone. One time I even had problem on other phone with really small rust on one pin that I touched with finger(sweat from it+time+really crappy weather where I had to use it), so it show how actually fragile phones are.
But few questions, when you managed to flash rom, you get all that android logo when you are in flashmode, and it show everything(loading bar etc) on screen?
Im asking because first symptom of bad battery connection is deformed or totally dead screen.
When you fixed gps antenna(that black plastic on top near camera) you used any tool that could damage board? its near microUSB so its easy to mess those small pins and make short circuit.
The same with battery, you could try to squeeze/move it a bit to see if there is any changes in phone boot behavior(not to gentle way to check it but sometimes it show if there is a problem)
Before changing motherboard I would replace battery from your other phone(charged before that) and check all pins on connector and board near it if there is any problem.
But as I said it should be made really delicate and in appropriate conditions.
Sadly I cant really help with it beside that, and I hope your phone gonna stand up after that somehow :/
Thanks for the reply Akinaro. Indeed the conditions are not ideal. At least I have one of those repair tool kits with the small screwdrivers, plastic pick and plastic levers for the connectors. I'll also set a reminder to take some latex/nitril gloves from the lab for next time
But few questions, when you managed to flash rom, you get all that android logo when you are in flashmode, and it show everything(loading bar etc) on screen?
Im asking because first symptom of bad battery connection is deformed or totally dead screen.
Click to expand...
Click to collapse
No, the screen is totally dead. No sign of life whatsoever.
When you fixed gps antenna(that black plastic on top near camera) you used any tool that could damage board? its near microUSB so its easy to mess those small pins and make short circuit.
The same with battery, you could try to squeeze/move it a bit to see if there is any changes in phone boot behavior(not to gentle way to check it but sometimes it show if there is a problem)
Click to expand...
Click to collapse
Possibly. I have used both the screwdriver and the plastic tools, but fiddling everything back in was tricky. The battery was disconnected though so it shouldn't have short-circuited. I will try with moving around the battery. But the more I think of it, the more I start thinking that I screwed up the motherboard by touching something there.
Before changing motherboard I would replace battery from your other phone(charged before that) and check all pins on connector and board near it if there is any problem.
But as I said it should be made really delicate and in appropriate conditions.
Click to expand...
Click to collapse
I have tried the other battery last night as well. I didn't charge it first though, I left it in my phone to charge overnight and tried to boot it this morning, without result.
So I've attempted to swap the motherboards. Good and bad news...
The good news is that the spare phone works with every combination of motherboard and battery, so neither of those is the culprit. The bad news: none of the combinations work on my own phone, even with swapping all the other hardware components (camera's, gps, antenna etc.).
On the other hand, by now the LED doesn't turn red anymore. The phone just stays completely off. I didn't have time to try and charge it for some time though, so I'm not sure if it's a good or a bad sign.
I fear that the main multiconnector running under the battery might be damaged when I took out the battery and antenna module the first time. That is the only component that I cannot swap for it is so integrated - it would mean swapping the screen to the spare-parts-phone and using that one.
Any ideas still before I should consider it a write-off completely?