Database Develop

big problem with acticsync

hey guys, i had to recently un-install activesync and then i re-installed it. however, now my computer, (windows xp) will detect my phone, and give me that screen asking me to install the drivers. i let it automatically install, and it gives me an error message saying it couldnt find the drivers. so i guess the problem isnt with activesync, but with the computer not being able to detect the phone... what gives?? thanks
omar

i had the problem but i had the att disk so that solved my problem but i believe as long as you have ativesync the computer should automatically recogonize your phone as a windows mobile device ...

Diamond with non-bundled AS?

Hey All.
I am on vacation, and just brougth a new notebook (lovely Medion Akoya), and i want to sync with my diamond. However, i downloaded the active sync from the ms homepage, and i get the "Unrecognized device" error all the time.
Yes, i tried to use different cables, yes i tried to deactivate the advanced network, however, i doesnt seem to recognize it at all.
Even if i do a softreset + volume down, i just get the SPL1-40 screen, but eventhou my phone is plugged in the USB, it doesnt say that, only "serial" when i disconnect.
I've been searching this forum the entire day, and i cant seem to find a solution. So, i kindly ask the gurus help me
Diamond running 0.95 bePe and pc running xp sp3.
Kind regards, Heien.

Try to flash a stock ROM and check if you run into the same problem.
In order to sync, you must be running the handset normally, don't enter bootloader mode.
Did the system prompt you for drivers the first time you connected it to the PC? Activesync 4.5 provides the rndis drivers.

the problem is, i cant even flash my device, i tried to flash it, but i get a connection error with the tool.
I know about the bootloadermode, and that i am not able to sync in that state, but i just wanted my pc/diamond to recognize the connection between them. The system did not prompt me for drivers, it just went straigth to unrecognized device. i even tried to point the the driverupdate tool to the drivers folder with the rndis drivers in the as folder.
-i also tried to hardreset my device.

Try doing the same on a fresh stock XP install, without firewall or anything similar.
We need to figure out if it's a problem with the handset itself or your OS/PC.
Try another USB port (DON'T use hubs).
Enter bootloader mode. When you connect it to the USB, it should at least toggle from serial to usb.
If that's the case, at least your USb is working well.

HARDspl won't install T_T

Guys,
I've been trying to install HardSPL to get this Touch X 9.0 Rom..
But every time i try to install it ask's me if i've connected the phone properly to the USB etc..
What can I do T_T ?
The phone is fully syncronized with ActiveSync

you can try other usb slot or a new computer .
nat

xRaitei said:
Guys,
I've been trying to install HardSPL to get this Touch X 9.0 Rom..
But every time i try to install it ask's me if i've connected the phone properly to the USB etc..
What can I do T_T ?
The phone is fully syncronized with ActiveSync
Click to expand...
Click to collapse
1) To be ultimately sure, take out everything that is connected on all USB ports (and I mean, ALL) EXCEPT your Xperia. Also, uncheck the "Advanced Network Functionality" of ActiveSync.
2) If you have the same problem after following my advise, change to another USB port. Try every single port.
3) If you still get disconnections, try another computer (or laptop).
4) Problems still persist? then check your USB cable itself (or the USB ports) if it is faulty.

[Q] galaxy s connection to pc thru usb

the only way to connect my GalaxyS to PC is running the KIES. If I don't run KIES it's not appeared in My Computer (although is charged).
I tried to use android screencast but it seems that the device in not recognized!
Any assistance pls?

also have this issue, although under some other usb connection modes my pc does recognise 2 external devices but can not connect to them what so ever
windows 7 64bit, samsung drivers installed

You can still use it as a usb mass storage. Only thing it wont do is updates. KIES is a known problem with many people. Some suggestion says to use the back USB ports. Some says to download the newest drivers.

[q] cant connect my huawei to my pc

I cant connect my huawei ascent p7 to my pc. i installe hisuite and i connect the usb cable to my pc but nothing happens. I didnt get any choises on how to connect it. Also i didnt see at all any drive from the mobile to the pc. i have enable the usb debbuging but it only charge the mobile. any help?

1. Did you choice HiSuite mode in notification panel after connection?
2. Did you install HiSuite on device?
3. Try installing MoboRobo on PC.
Sent from my HUAWEI P7-L10

after a few restarts on pc and on my mobile i finally did it. dont know whats wrong but now its fixed

marsian720 said:
after a few restarts on pc and on my mobile i finally did it. dont know whats wrong but now its fixed
Click to expand...
Click to collapse
Up till now I still cannot connect my p7 to my pc. I also cannot find the usb debugging in my phone.