Stuck on 4color Screen/Killed my BA? - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hi everybody,
im afraid i have killed my german XDA III from o2 (HTC BlueAngel).
I just tried to instal WiMo6.5 on it...but i think it was a mistake, cause it has never seen any update since 2005.
Now im stucked at the 4color screen. It just shows me R 1.10.00. Nothin more...and i could get into the Bootloader by pressing Windows Media + Record.
I already tried to update the Radio to 1.15.00...but it always says the new radio-version isn designed for my XDA III.
So i would try to bring a runnin win2003 back on the XDA III, but i could find any working version of win2003 :-( found a dutch one, but it didnt work...country error...
So i need some help with this...i just dont want to throw it into the garbage :-(

ok, just tried it with the latest version from o2...got a model id error...damn it...
edit:
ok, got the latest version of the o2 ROM...but still noch way to update the Radio to 1.15.00...

ok, sounds like a bad flash, if you can get into bootloader all is not lost, just flash another WinMo onto it, Helmi wm6 is a good one, thats the one i have got.

ok
first after WM5/6/6.1/6.5 upgrade you must perform hard reset like is described here
a lot of shipped roms can be found in my signature - i also have original GER XDAIII roms
for radio and rom upgrade you can use MAUpgradeUT_NOID - also in the page in my signature

Related

Charmer crashed with the new Aku 3.3!

Hello!
I tried to flash my Charmer with the new german Aku 3.3. At first everything seems to be ok, but at 95% it stops and i got the Message: update error- there is an comunication problem! So what can i do? I tried to flash the old rom back but there comes also at 95% a message: invalid command - nfb file cannot be used for your pda!
Please help me !
Greetings Musna!
Ps: can somebody upload a sd image for the mda compact II !
Go to bootloader mode, then try to flash RUU rom (1.x). You can find it on Charmer wiki.
It doesn`t work too, it always stops at 95% has anyone another idea?
did you try hard reset?
Yes i tried hard reset, but it is always in bootloader!
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
nitrane said:
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
Click to expand...
Click to collapse
The aku3.3 is up to date the bootloader version!!!
IPL and ISP version now is 3.00.
http://www.windowsceportal.hu/forum/viewtopic.php?t=1079
Sorry but i do not speak hungarian. What do you want to tell me ?
I´ve got the same: My charmer is in Bootloader IPL 2.06.0001 SPL 3.08.0001
I can´t downgrade to AKU 2: Please order a newer Version.
Every try to upgrade to AKU 3.3 failed at 95% with Error 326.
Is there any help for my charmer???
oh.**** !!!! I got the same problem with them and my first pda uk rom already empty screen and then i try with my scrond pda German rom it the same problem and now just only show in bootloader screen.Have i ask someone who knowage about this he told me that if SLP in you PDA have chang it be hard to repair.So,I think I lose 2 PDA did I try to flash in T-Mobile Official Rom de that i hope to develop it but i hve to kill 2 Charmer.Who take responsibilities,T-Mobile right ???
Ok no problem you can repair it! At first you have to brand your device with the rom you want to! After 95% the Problem will come again! When it stops you have to go with a reset to bootloader again.When your device is in bootloader you have to install the Radio Rom from this thread:
http://forum.xda-developers.com/showthread.php?t=302768
After that your device will be able to boot again and it should work!- But the Problem during the installation will stay,so you have always to use this way to flash your Mda compact II!
In the new rom there must be a problem with the radio rom and this causes the broken device.
I`m sorry for my bad english but i`m not used to talk very much! So i hope you understand what i mean!
Greetings from Austria Musna!
that link is broken
Then try this one:
ftp://xda:[email protected]/Prophet/Radio_Roms/Prophet_G4_RadioRom_v2.47.11.exe
You can find the radio rom also on the ftp server. Prophet> Radio Roms>Prophet_G4_RadioRom_v2.47.11.exe
You can try different Radio Rom versions, i have flashed the v.247.11 and it worked.
Normaly it should work!
Thank u so much !!! My Charmer secrond PDA come back have life again and it can working.So,my Charmer first PDA UK rom still empty screen and notthing working when i press any button.Who can slove this problem !!
Musna do you have any massage such as msn

Bricked Vodafone Kaiser ... HELP!

Hey Chaps,
Just thought earlier today i'd have a go at upgrading my phone with the new HTC firmware for my Vodafone Kaiser. First i tried it on it's own only to find the 'vendor' had blocked the upgrade, then i ran the HARDSPL software, when it rebooted my phone to the tri-colour screen i stopped pressing enter on the batch file and ran the HTC upgrade again! ... success - sort of; the upgrade got to 15% and stopped with a connection error (my usb's dodgy i think), then when the phone rebooted to the tri-colour boot loader it'd a) no longer accept the HTC Rom (vendor thing again) and b) become irritatingly broken.
Is it possible to flash an older vodafone rom to the device? if so, where can i find such a beast. Or does anyone know of any devilish ways to put the new rom on using the bog standard bootloader?
Thanks in advance big time to any clever phone experts who can de-brick my... er... brick
Dan.
your supposed to install hardspl before upgrading it if you try it on its own it will brick it at least thats what i heard from the stickies
azazelx, he has hardSPL installed, anyway.
@JimmyJangle: flash via microSD card. [url="http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash" URL]Read here.[/url]
You need winrar to extract file nbh from the shipped ROM.exe.
Hmm, i don't think i do have HardSPL actually installed,
When i saw the tricolour screen come up with different version information I stopped that batch file that was installing HARDSPL (impatiently) and started the HTC one (which failed at 15%). So now i (think) i have a phone with no firmware and the bootloader says:
KAIS130
SPL-1.56.0000
CPLD=8
I reckon if i can find a vodafone made rom the bootloader'll let me install it.
Any idea where i could find one?
What is ur orginal shipped ROM?
Your solution now is flash back the orginal ROM by using microSD card method I mentioned above, install HardSPL succesfully, then flash whatever ROM you prefer.
Hey Nghiem,
Thanks for the help, that link doesn't go anywhere though.
Also, wouldn't i need the original rom from somewhere in order to do that?
Thanks,
Dan
where did you buy the phone e.g vodafone, orange, etc...so I can tell you the original ROM? Because you phone CID is not unlock, hence you must flash the back the shippied one.
Get the WM 6.1 Vodaphone official here http://forum.xda-developers.com/showthread.php?t=365058
Hi,
I got the phone from Vodafone in the UK.
It had WM5 on it... erm, that's it.
I've just beem trying to load original voda roms back on to it but it's not happy - i don't know if they really are the originals though, one says 'reconstructed'.
Dan
Actually, that was the rom i tried and it came up with the Vendor ID error.
Dan.
Link on post #6 is the official not reconstructed. How about download directly from Vodafone website? It's strange when you have carrier ID block even with its ROM. Also, try reconstructed ROM listed here http://forum.xda-developers.com/showpost.php?p=1586817&postcount=2
Search for mtty, see if it can help you out.
MTTY saved the day!
Only 3 hours of my life lost!
Thanks,
Dan
Cheers. Don't forget to flash HardSPL and read the wiki before doing anything.

Bricked Wizard

sorry if this post seems to be a repeat , but i tried the search option and the results were not fruitful
a friend of mine , while trying to upgrade to a TNT ROM , didn't HardSPLed the device first , and successfully changed the ROM of the device , now it is stuck on the blue screen with SPL and IPL versions , and no response . for some reason , the device can go to bootloader mode , but it can not be reflashed , and it does not respond to a hard reset command.
please advise on what to do
regards
When it is in the bootloader mode, and connected via USB, is there a little USB icon in the bottom left? If so, simply flash your phones carrier ROM and all should be fine with it again. You can then apply HardSPL and flash to the TNT or any other ROM that you want to. Is your device a G3 or G4 by the way? What are the numbers after IPL and SPL?
well my friend says that the USB icon is visible there , and the device was indeed a G4. the thing is , what exactly should he do , in order to flash the ROM , since non of imate roms work for it. should he use any special software?
i'll greatly appreciate your help
Is he using Vista or XP?
he is using Windows XP , could it be the PC OS that caused interference?
Well, only if it is Vista does it really matter. He needs to get ahold of an original carrier ROM, such as the O2, or T-Mobile one and flash it to his phone, then HardSPL it, then upgrade to 6 or 6.1.
Download and flash Wizard_love Rom,it might do the trick,then HardSPL and upgrade to any wm6 or 6.1 rom.
What exact error it gives while flashing imate official rom ?
well the wizard has been an imate ,and it was flashed with an Original imate ROM already , but no success , any other suggestions?
thanks again
error [294]invalid vendor ID :
This Update Utility can not be used for your PDA phone.Please check your update utility.
here is the picture
http://i35.tinypic.com/29v03rl.jpg
and could you please give a link to the Love ROM?
thanks
Download wizard_love Rom from this link:-
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
well he first got this error while upgrading
http://i33.tinypic.com/ivjz8o.jpg
then he managed to upgrade , but had the very first screen after ugprading on PPC screen , and nothing happens
it also gives a failure message while trying to manually Hard Reset after upgrade
please advise on what to do next
greatest appreciations
No SD Upgrade even tough... MTTY hahahaha
king_dani said:
well he first got this error while upgrading
http://i33.tinypic.com/ivjz8o.jpg
then he managed to upgrade , but had the very first screen after ugprading on PPC screen , and nothing happens
it also gives a failure message while trying to manually Hard Reset after upgrade
please advise on what to do next
greatest appreciations
Click to expand...
Click to collapse
It seems you need to follow the drugstore MiniSD upgrade but...
I guess you dont have another wizard to make a bacuk up... so wait a minute...
You don have hardspled yopur device...!!!
HAHAHAHA forget it!mmmm
Maybe mtty... folow mi signature maybe works
See you There Men!!!!

New Official ROM Upgrade- Release Date: 2009-04-14

I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23
Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks
Ht845kh14923 :d
o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??
It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???
Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Could anyone check, if the gps-support has been improved?
km
lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725
GPS seems to work fine now, also the scroll behavior of opera is better
km
It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint
Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?
Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer

Problem with HTC Kaiser Tytn II - please help...

So my problem is - I put android on my htc tytn II and it worked (well kinda) but anyway I decided to switch back to Windows Mobile...
I installed 1.27.x.x radio , found a Windows Mobile 6 ROM and put (Like in the instructions ) Kaisimg.nbh(renamed from ruu_signed.nbh) and Kaisdiag.nbh to my SD card and then started flashing... It flashed smth,rebooted automatically and started booting android again...
Then I hold again camera button + power+ reset and since then when I put EVERY .nbh file on my sd card and try to flash it it STUCK on "Loading.." If I try to flash it with USB It stays at 0%.
The only exeption is if I try to flash from USB the rom that I tried to flash before from my sd card.. then it starts 0%..1% and reboot the phone...
P.S: Please help me...I think my device is not Broken but I dont know what should I do to fix it...
To flash back to WM from android put your kaiser into bootloader (multi colored screen) Then connect to usb. Download any WM build that is recent (I suggest Phoenix 3 for this, you can flash whatever you want later). After you download it open and run the included RUU that came with it and it will flash it on there.
hmm, I also had experienced the similar problem on my 1st time flashing back to WinMo.
When you are trying to flash via USB cable and the process stopped at 1% I guess there is also a message about "Invalid vender ID" right?
and if the text in your bootloader (tricolor screen) doesn't mention anything about hard such as "3.29.0000" (not "3.29.hard")
then
you've lost your hard SPL that's why you cant flash any .nbh to your phone.
I had managed to solve this problem by flashing stock WM rom for kaiser. The rom also has to be suitable for your phone, I mean if your kaiser is originally from France, then use French kaiser stock rom. Or if you are using AT&T Tilt use kaiser cingular stock rom.
you can find the list of shipped roms for kaiser here :
http://shipped-roms.com/shipped/Kaiser/
If you still have the "invalid vender ID" error message, try another stock ROM.
Thanks man you're my hero! I though I lost my phone.. anyway i bought new one - Nokia 2730 Classic but Ill sell the kaiser...
Thanks Anyway ... you're god!
Have the same problem...
Firstly, I'd like to point that the reason for the hard SPL getting overwritten by an original SPL is NOT HAVING UPDATED HARDSPL to a newer version that prevents accidental overwrite. This is instructed in the previous steps before actually installing Android. That was my mistake (I had HardSPL 1.0 OliPof), and now I can't flash no rom to my Kaiser (which thankfully works quite well in Android).
What happens (please correct me if I'm wrong) is that "KAISDIAG.NBH" is a modified, standalone hardSPL that will flash to the phone the SPL that comes with the "KAISIMG.NBH" you put in your SD card with "KAISDIAG.NBH"). In my case, I used the WinMo 6.1 spanish version 3.29.412.0, which, resulted in my phone being flashed with the original SPL 3.29.
Now, it seems many users have fixed this locating the correct stock rom and flashing it in their Kaisers. But to others, like myself, nothing seems to work. I believe that this is because we not only need a stock rom for our specific Kaiser model, but also it has to be compatible with the SPL that accidentally got installed in the phone. The problem is what if such rom doesn't even exists?
I'm really thankfull for all I learned by reading the forums (and from my mistakes ) and I know I'm in no position to make requests, but here goes what I think could help the users like myself to fix this, if posible:
1) Guide to identify what model of Kaiser we have (maybe it's already there, I just couldn't find it)
2) Complete list (or lists) of stock roms (There are some around, those are easy to find I think, but it doesn't hurt to share different sources)
3) Something like a JumpSPL for Android would be more than awesome...
Thanks in advance to everybody, sorry for my own stupidity . Any idea or help would be much appreciated,
Daniel
hmm, I'm not sure if it has to be compatible with the SPL.
In my case, I was flashing a very old WWE stock rom which has original SPL 1.56.
I also had been very desperate because any stock rom I found seems doesn't work and I even didn't know where originally my kaiser came from because I get it from my uncle. So I tried to flash any WWE stock rom I could found but nothing works. I read from Wikipedia that based on my phone model (Kais100), this model was only sold as AT&T tilt for US. But the problem is my phone is HTC branded, not AT&T tilt. Well, based on this information I also tried to flash some cingular stock rom but the result was just the same.
After contacting HTC Customer care, I know more info about my phone. They told me that based on my phone product ID, my kaiser was originally shipped for US, but unfortunately they can't provide me stock rom for my phone model. So I searched myself but this time I had better objective : to search HTC branded rom but for US.
finally, after days of search. I've found the rom that is suitable for my phone. Its called HTC WWE Brightpoint US which has original SPL 3.29 at the bottom of the list on the website I told you on my previous post.
few weeks ago I also accidentally overwrite my HardSPL again, but this time I did it with the stock ROM which has original SPL 3.29. But this problem also solved by flashing the stock ROM I've found before via USB cable.
So, I guess it has nothing to do with spl version.
Keep tying don't give up.
Update: Step 1 completed! YAY
Using the serial number and some obscure google searching, I came to the conclusion my KAIS130 is australian. Cheers, mate!
I verified this by being able to download stock roms from the australian HTC site with my Kaiser serial number. But at the moment of writing this, have downloaded two roms and no luck yet. 5 minutes remaining for the third one... Wish me luck...
Daniel.
Well... Now what?
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
cuartetoraro said:
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
Click to expand...
Click to collapse
sorry to hear that..
well, extract the .nbh from exe and flash it via sd card is the method that made me overwrite my hard SPL in the first place.
hmm, did your phone comes with operator brand, such as three or something?
-Rif- said:
sorry to hear that..
hmm, did your phone comes with operator brand, such as three or something?
Click to expand...
Click to collapse
No, it's HTC unbranded. Now, something strange here: the label behind the battery has the serial number: HT830GB06075 and the P/N (guess it's part number) :99HCY194-00, but to the left of the camera, another label with the part number: 36H00563-00M and below says DATE:061107(TB02)/US.
I don't know if that's normal, but it caught my atention because my phone seems to have been dissasembled (little label over screw is teared). Maybe my Kaiser isn't Australian after all...

Categories

Resources