Hey guys,
I used diamond then shifted to Omnia and now back on Diamond.
Diamond was never able to use airtel live and the customer care people used to say that the service is not available to any Windows Mobile Device and i need to buy Mobile Office to use net on my cell. Bull S***..!!
Then i went to Omnia and it was able to run Airtel Live. Damn.. Whats wrong with Diamond then.
For some reasons i shifted back to Diamond and searched day and night to find out the solution. Here it is:-
1. Activate Airtel Live by sending the following SMS to 121: MASALA ACTIVE.
2. The service takes atleast 3-4 hours to get active. Restart the phone and resume configuring.
3. Tap Start -> Settings.
4. Select Connections Tab and tap Connections.
5. Select Advanced Tab, tap Select Networks button to bring up Network Management.
6. Under "Programs that automatically connect to the Internet should connect using:" drop down, tap the New button.
7. In the General Tab, type the name of the settings as Airtel Live
8. Select Modem tab, tap New...
9. Type the name of connection as Airtel Live, select the modem as Cellular Line (GPRS) and tap Next.
10. Type Access Point Name as airtelfun.com and tap next.
11. Leave username, password and domain blank and tap finish.
12. Select Proxy Settings tab. Tap "This network connects to the Internet". This should enable the next check box option.
13. Tap "This network uses a proxy server to connect to the Internet".
14. Type the proxy server as: 100.1.200.99 and then tap Advanced...
15. Tap HTTP, leave the server as 100.1.200.99 and change the port to 8080
16. Similarly tap WAP, Secure WAP and Socks, type the server as 100.1.200.99 but leave the port to defaults. These are optional settings.
17. Tap OK to close the Advanced proxy setup screen.
18. Tap OK to close the New connection screen.
19. The network management screen should now list the new connection you have created in the drop-down. Tap OK to close this screen
20. Tap OK to close the connection screen.
And its done. Use IE or Opera and have fun.
Njoi..!!
do leave a "Thanks" if it works out.
I did all the steps and after them there's the Edge icon on the signal bar when some application try to connect to internet...but i still any application is not able to access the internet. When I open the site in IE i get "Request not authorized to access WAP gateway". Also its not that I don't have WAP access on my Airtel connection, the same SIM is able to access WAP sites through nokia's default browser in my older nokia 6600
NOP still works? i thought it was stopped sometime back. Will try it out.
umm..any idea whats the downloading/browsing charges?
btw..i'm in bombay
Mafioso said:
I did all the steps and after them there's the Edge icon on the signal bar when some application try to connect to internet...but i still any application is not able to access the internet. When I open the site in IE i get "Request not authorized to access WAP gateway". Also its not that I don't have WAP access on my Airtel connection, the same SIM is able to access WAP sites through nokia's default browser in my older nokia 6600
Click to expand...
Click to collapse
i used to use NOP to browse net on my laptop.
airtel tried to act smart, it blocked many browsers so that only few browsers can access the web. on my laptop, i changed the user agent and worked like a charm
hmm...for mobile...i used opera mini
fazalali110 said:
i used to use NOP to browse net on my laptop.
airtel tried to act smart, it blocked many browsers so that only few browsers can access the web. on my laptop, i changed the user agent and worked like a charm
hmm...for mobile...i used opera mini
Click to expand...
Click to collapse
I think NOP has subscription charges as 100/month...
cool. its working. another reason to luv my diamond
gmail problem now !
Blackberry connect, on htc pp300 running onWM 6.1, used to freeze the mobile frequently. After making these changes, there are no more hangs
Now gmail connection has stopped working. I get an error "error synchronizing". I tried both POP3 and IMAP connections. Any suggestions on how to fix the problem.
Related
have BB Connect installed on my Kaiser. I am able to get emails successfully over Blackberry and gmail. However, I cannot use Internet explorer over MediaNet.
GoogleMaps, the weather plugin, QuickGPS, etc can all get the data they need when connected through MediaNET but IE will not load any webpages. Also, if I connect to a wireless lan, the same thing happens. IE can't browse, but other apps access data just fine.
Any thoughts on how to fix this? There are no options to config connections within IE and the connection within settings seems to be correct (how else would the other applications be able to use MediaNET?).
Are there some proxy settings I need to change or fix? I was able to browse the internet with IE via wireless lan or medianet perfectly fine before BB Connect was configured.
Note:
I can launch BIS for internet explorer and use the Blackberry connection instead of MediaNET. Obviously though this is not optimal as BIS has lmited sites, low res pictures, etc.
I've noticed the same behavior. It happened when I opened the "email settings" icon. This opens pocket IE with an extra menu item. Since then, wifi works for all programs, but pocket IE just gives me a blank page...
Did a hard reset, and never used the 'email settings' thing again. Everything is fine now...
I've noticed the same issue. I've set my connection to medianet using the proxy, noproxy isp.cingular.com and wap.cingular.com. All other programs are able to get to the internet (google, live search, BBC internet explorer, etc.) except for the standard IE. I don't browse too often, so I use the BBC browser when I need one.
thanks all ... i know now not to click the email settings button ... did a hard reset and all is well ... MediaNet full web browsing kills BIS
Internet Explorer inoperable
Help please! I am using the Kaiser and have the following issues.
1. There are 2 capital 'E's in the top. One that says Blackberry Edge and the smaller E says Tmobile Blackberry Edge when tapped
2. I can not simultaneously use the browser to access the internet at the same time that I am using the blackberry service to access emails. One of the 2 must be suspended.
In other words, I would have to literally suspend blackberry in settings to go surf the web.
Does anyone have this issue? Can anyone at all offer assistance to correct the settings so both can work together.
Any leads greatly appreciated!! Michael
i am having the same problem. did not find a solution. started using xpress mail
Hi,
I have the same problem with my HTC Kaiser and T-Mobile Germany.
The funny thing is that T-Mobile doesn't support Blackberry on this device.
I just installed the BBConnect_WM6_Professional_BB_41.0.0.84.cab and restarted the device and was happy that all works fine. I got all my mails from company BES server, includes the security features which lock the device every 15 minutes.
If this will work with Blackberry mail for home users, I don't know. I tested the BBConnect only to our company server.
I have the same problem like users here has in this threat:
I can't use the Internet Explorer to browse in the Internet. That problem still exist on WLAN and on GPRS. I turned off the phone part and try to use WLAN, but I have the same problem.
I guess that the Blackberry Connect will modify the Internet Explorer (like other parts of the device) to enable security features.
If I use the Blackberry Browser I got the message that the service is not supported. I know that some colleague had the same problem with their Blackberry (Hardware device) and called T-Mobile to enable the service.
I can user Google Maps, IMAP-Mail profile, Weather software and other stuff from the Internet without problems (WLAN and GPRS), only the Internet Explorer and Media Player has problems to connect.
To solve the problem I will talk to the BES Admin or / and T-Mobile. If this will not solve my problems, I will install Opera Browser, which will hopefully work.....
Here are my versions:
Rom: 1.56.111.4 - 09/01/07
Radio: 1.27.12.32
Protocol: 22.45.99.07H
Erik
You have to go to registry:
hkey_current_user->software->microsoft->windows->current version->internet settings
and delete enableautodetect entry
This solve the problem for me
xklipschx said:
Are there some proxy settings I need to change or fix?
Click to expand...
Click to collapse
You can modify the registry key 'EnableAutoDetect' key found in the registry location:
[hkey_current_user\software\microsoft\windows\curre ntversion\internet settings']
The default setting (that uses the proxy) is:
"EnableAutoDetect"=dword:00000000
(To disable proxy) Change it to:
"EnableAutoDetect"=dword:00000001
The best option is to delete the registry key (which I did) since some posts indicate this registry option gets set to 0 after a reset.
sancho1234 said:
You can modify the registry key 'EnableAutoDetect' key found in the registry location:
[hkey_current_user\software\microsoft\windows\curre ntversion\internet settings']
The default setting (that uses the proxy) is:
"EnableAutoDetect"=dword:00000000
(To disable proxy) Change it to:
"EnableAutoDetect"=dword:00000001
Click to expand...
Click to collapse
Hi,
I changed the IE settings EnableAutoDetect from 0 to 1 and everything works fine.
I tested Opera Browser as well and it's fine, but I don't like the Bookmark synchonisation, this is better in IE....
Thanks a lot
Erik
Heya,
I have the same pb
BB push mail OK
pocketie, gmap ... NOT OK
Enableautodetect is allready 1
what's yr network setting ? "My blackberry" and "my Blackberry" ?
Please can you list me all
Tks a lot,
Nicolas
I have been searching thru the forum and i can't find any specific information about it
i use windows live messenger, email , and browse with Opera...I do use live search and google map too and i am with the 19.99 total internet plan now..
Just want to see if it is possible to save the 13 bucks coz i don't need hotspot at all....
I have seen posts that about changing proxy and get the internet with PIE to work but it doesn't mention about other programs like tomtom google map live search and i don't want to change it to the T-zones without confirming this.
Could anyone help please?
i'm in the same boat as you, the 5.99 works on my dash, so i'm expecting it to work on the tilt, but i just cant get it to work...now when i open up PIE, it goes from connnecting, to loading to opening, and just stays there and then gives me error #502... so if you figure it out, def let me know, thanks
omar
Same here, I have posted a thread about it already but no replies, Here. Do let me know it thr is any, n i'll do the same.
I can confirm t-zone plan works fine with google map, push mail to exchange servers, browsing using IE, and regular smtp/pop email. The weather update progam on the today screen does not work. On the other hand, SBSH Pocket Weather does work (I let it update throughout the day). NTP time server service also does not work (using CityTime).
1. add new modem connection -- cellular line (gprs, 3g);
2. access point name -- wap.voicestream.com
3. leave password blank
4. proxy settings check "this network connects to internet";
5. check "use proxy server"
6. proxy server: 216.155.165.50
7. advanced: change http port from 80 to 8080
Under network management, set Internet Connection to the account just created above. Leave private network as "My Work Network".
Soft-reset.
If you have trouble with POP accounts, edit each POP account and change connection away from "My ISP" to the t-mobile account.
Cheers
Okay i have tested this setting for T zones and i am trying to add a few details on it.
1st. Windows Live and Windows Live Messenger does not work =/ I guess it is because it doesn't support proxy connection. I am wondering if anyone can somehow mod it or change the proxy settings of these two programs with registry or other means so i can actually use it?
2nd. PIE works right away with the setting, but Opera won't. Later i add the proxy server in the Opera setting then it works like a miracle too=)
3rd. Some other IM site such as communicationtube.net does support the login of msn using T zones...Kind of a substitute even tho the stock messenger works much better.
4th. for 13 bucks/month the only different is probably only on Windows Live and Windows Live messenger....or if someone can actually provide a mod version of these two programs or a tweak that changes their settings. T zones works perfect for kaiser...
I can confirm that GMM works with the method listed in the link below with the $5.99 T-Mobile Web plan and WM5. But "My Location" does not, may be my phone (Cingular 3125) http://www.ehow.com/how_2245457_tmobile-shadow-any-windows-mobile.html
AT&T Tilt won't connect to GPRShttp://forum.xda-developers.com/newthread.php?do=newth
I've been having problems getting my unlocked AT&T Tilt to connect to T-Mobile's GPRS data network. I've done the necessary connections setups, including entering the proxy server settings (216.155.165.050:8080, etc) as well as running the disablehiddenproxy .cab in the Windows folder, but it just won't connect. And, when it appears to have connected, I can't access any websites. Every attempt simply ends up with an error message with something like 0x8008000. Google Maps won't work either, so the issue isn't limited to PIE.
I've entered the same settings on multiple phones in the past, including two HTC phones (Dash and Wing), so I know I didn't mess up on any obvious settings. I don't know what could be wrong. Has anyone experienced this before, and if so, what did you do to fix it?
Thanks.
Anyone? So far still no dice. WiFi works, though, which I guess is something...
EDIT: Nevermind, I think I got it. Apparently I needed to clear the SOCKS proxy setting. It's news to me, as I didn't need to do that before on either the Dash or the Wing.
Anyway, if anyone else is having the same problem, here are the instructions (specific to the proxy settings) I found and followed to get it working:
Go to set up proxy server
Check box that says “this network uses a proxy server to connect to the internet”
In the proxy server type 216.155.165.50 (you might want to highlight and copy because you will be using this setting 3 more times)
Tap advanced
Tap HTTP (if the server is not filled out paste the proxy settings in the step above in the server box) and change port from 80 to 8080 then hit ok.
Tap WAP and paste or type the same proxy server (216.155.165.50). The port should automatically say 9201. Leave this as is, then hit ok
Tap secure wap and paste or type in the server settings from the last 2 steps. The port should say 9203. Leave as is as well and hit ok
Tap Socks and clear the server setting. The port should go away. Hit ok, and you're done.
I have just upgraded from a DIAM 100 to a 130 so now 3G works beautifully.
However my mail set up fails to synchronise (both bigpond and windows live).
It will work on wifi but will not work otherwise (full 5 bars reception and internet does work.)
I figured it must be the settings for my telstra internet/wap setting however when i go into connections, it tells me that this is preconfigured and cannot be modified.
So has anyone else had this problem and how did you fix it.
I have wasted several hours of on hold to Telstra so I thought I would ask this forum first.
I have searched the fora without success for this problem.
Many thanks
thedoc said:
I have just upgraded from a DIAM 100 to a 130 so now 3G works beautifully.
However my mail set up fails to synchronise (both bigpond and windows live).
It will work on wifi but will not work otherwise (full 5 bars reception and internet does work.)
I figured it must be the settings for my telstra internet/wap setting however when i go into connections, it tells me that this is preconfigured and cannot be modified.
So has anyone else had this problem and how did you fix it.
I have wasted several hours of on hold to Telstra so I thought I would ask this forum first.
I have searched the fora without success for this problem.
Many thanks
Click to expand...
Click to collapse
Flexmail for the win!
I have exactly the same problem. I'm assuming the Teltra ROM is locked down and you can't do much with it.
The problem is the proxy settings, don't enter them and you will be able to use msn and email, but you will loose access to the "free to browse" Telstra pages
Copied from http://configure.telstra.com.au
1. On the handset, tap on the Start button.
2. Tap on Settings.
3. Tap on Connections tab.
4. Tap on Connections icon.
5. Tap on Add a new modem connection under My Work Network.
6. Enter Telstra Internet in the Enter a name for the connection field.
7. Select Cellular Line (GPRS, 3G) in the drop down list under Select a modem.
8. Tap on Next.
9. Enter telstra.wap in the Access point name field.
10. Tap on Next.
11. Enter a username in the User name field or otherwise leave it blank.
12. Enter a password in the Password field or otherwise leave it blank.
13. Tap on Advanced.
14. Select Use server-assigned IP address.
15. Tap on OK.
16. Tap on Finish.
17. Tap on Set up my proxy server under My Work Network.
18. Make sure that This network connects to the Internet and This network uses a proxy server to connect to the Internet are checked.
19. Tap on Advanced.
20. Tap on HTTP.
21. Enter 10.1.1.181 in the Server field.
22. Enter 80 in the Port field.
23. Tap on OK three times.
Fix in Advanced Server Settings
I had this problem and fixed pretty easily by going into email inbox tab, then press menu / tools / options then tap an account to change its settings. click 'edit account setup' press next a couple times until you get to a page with "Advanced Server Settings" down the bottom in blue. click on that and change the network connection box from 'The internet' to telstra internet. click done and next til the setup is finished and you should be able to get your mail over the 3G connection
sorry if this has been asked a million times before i have been searching for two days trying to get the internet to work on ya sons touch diamond
this phone was on contract on o2 he is now trying to set it up on his pay and go simplisty sim which includes free internet .
I have tryed so many different settings to get the internet working and email
all i get are network error messages.
the only way i can get it to conect is via wifi
and help would be great thanks in advance
Gary
Theres a cab file with the settings in. I cant remember where i got it from, but if you PM your e-mail address i will mail it to you.
I think its called DeploySP.cab
Hi, I'm on the same network and on the Text and Web simplicity tariff. Here is what I did. The Windows mobile version I'm using is wm6.5.x, with the start menu at the bottom left.
To enter the settings first click "start", then click "setting", then "connections".
First click manage existing connections, and delete the modem connection specified in here. (Not required but advised) As this is configured by the device and the setting are incorrect.
Next go back a step. Then click add new modem connection.
“Select a Modem” should be set for “Cellular Line (GPRS)” or “Cellular Line GPRS/3G”
Now click “Next” to start inputting the operator specific settings.
Name the connection: O2 (PAYG)
Access Point Name (PAYG): payandgo.o2.co.uk
Username (PAYG) payandgo
Password: password
Tap “Advanced” and make sure both tabs have selected “Use Server Assigned IP Address”
Tap “Finish” then Tap “Proxy Settings”.
Select “This network connects to the Internet” and “ This network connects to a proxy server…”
Tap “Advanced” then WAP. Server address is: 193.113.200.195: Port 9201. Tap OK
Tap Socks: Server is 193.113.200.195: Port 1080. Type: Socks 4.
I can confirm these settings work as I use the internet everyday on my Touch Pro. Hope this helps. If you struggle pm me.
Hello sb.oddworld,
Working on HTC Kaiser on O2
Many thanks,
SW ;o)