Related
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
no ideas guys?
so no one can help me with an idea???
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600
Do a hard reset and flash an OFFICIAL ROM from SD-card
Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.
thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?
If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.
nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out
Hi, i've bough a p3600 on ebay.
The seller tell me the phone is out because he flash a bad radio version on the phone.
I try to upgrade some file. ( Rom OS, Radio, SPL,etc ...)
I try the splexploit...
BUT ... The phone already stay on startup. i can see HTC startup screen,the windows startup screen ...but never the today screen.
I try hard reset, htc official rom, cookeed rom,...but when i flash a rom with "gsm", the update freeze at 13%
I try with usb and with sdcard..same thing, already stay at 13% !
But if i flash hard spl, 100%, if i flash OS, 100%, just the radio freeze at 13%
Any idea please ?
update
after the boot, i've got a "no gsm" message near the radio version
other people got the same problem like me ...
God oli, help me please
I more or less had the same thing and solved it with the sc card flash page.
http://wiki.xda-developers.com/index.php?pagename=Trinity_SDCardFlashing
A rom that works for me to flash it back to the working original
http://www.allaboutphones.nl/forum/request-originele-spv-m700-rom-p3600-rom-t727.html
To download you have to register with them.
GL
Hi, updating the radio to 1.56 crashed, now I have the No gsm message and doesn't boot, running mtty from bootloader with info2 command it says supercid but I can't update any official rom SPA, WWE, ITA... the error is "vender id invalid". I've tried the sd method but returns to bootloader .
Any help will be appreciated.
You should try SSPL : http://forum.xda-developers.com/showthread.php?t=293632
And if it doesn't work the Des' Crash-Proof SPL :
http://trinityguides.info/index.php?option=com_content&task=view&id=39&Itemid=66
and try to flash a radio rom again !
doesn't work
try again and again ...the phone block at 13% ( when the radio upgrade begin) ...
pfffff
I've the same problem and after several attempts without result I sent the phone to the workshop and they told me the problem is with the main board! (this cost almost the price of phone itself). Moreover, I've seen some where here that the problem could be caused by radio chip but I couldnt get the detail.
If you find a solution give me a tip.
i've test lot of thing.
I progress with mtty. but i've got a problem ..i can't downgrade the phone under SPL 1.05.
SPL 1.04 can "reset" the radio, or enter directly to the radio bootloader. With that, i can save my phone.
Try mmty (see the wiki => bootloader info) and with the mfg spl, you can try the method.
Guys,
I've got the same problem...
I've sim and cid unlocked my spv m700 some time ago, using wonderful software from pof. Everything went smooth.
Today I've decided to update radio rom to 1.38.00.11 to enable gps.
I've launched RUU, everything was ok till 44%, when I've got message "Communication error".
After that program tried to recover rom without success, I've got another message "Image corrupted"...
I've tried to reboot my spv (both SR and HR), after rebooting I see:
M 05
B 05 D 1.23
then those symbols disappear and I see only Orange logo.
That's it... The end...
Should I reload radio rom or both rom and radio rom to my DEAD spv? If yes - how?
Please help as I'm very disappointed, frustrated and so on!
Thank you!
Update: A-A-A!!! I did it! I revived my spv! Let me explain how (I'm kinda new to all this rom and and ssl things, so forgive me for mistakes, if there are any):
1 I ran unbrick software. Yesterday it did not work (said, that could not find smth), but today it worked fine.
2 I ran RUU and BINGO! That's it!
BTW, I have vista, but it still worked (I think, thanks to Windows Mobile Device Center, which I have installed).
Also, I killed wmd process in Task manager in the beginning (have read this recommendation somewhere).
Thanks to everybody for their help!
nyco,
could you please explain briefly what you did exactly and which radio and rom you used
thanks and regards
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Thanks stepw...
when I hit task 2A nothing happens.
Original ROM doesnt respond. I flash with cooked ones. Result 100% successful. I restart the phone- hang at boot screen.
stepw said:
Flash HSPL, then issue task 2A command from mtty. Flash full ROM.
Click to expand...
Click to collapse
Hi,
I'm already under the hard SPL. and "task 2A" not working.
Macars, try only with radio ripped or full original rom (from htc or cooked with radio) because some cooked rom have only OS.
Can you tell me what SPL you have?
Hard SPL?
Have you try splxploit ?
Can you tell me what rom you try oviplokos1 ?
thanks,
it shows SPL 9.99 and with this I cannot flash anything so what I do is to update with splxploit and then the phone changes to SPL 1.2 olipro. With 1.2 I can only flash coocked ROM and will go until the end 100% successful- (original ROM the phone does not respond), but when restarts with newly loaded cooked ROM the phone hangs at window login screen and when put it in bootloader the SPL 9.99 returns again.... the story goes on like this.
I'm becoming mad....
hi,
you can only flash cooked rom because the rom you flash contains only OS. When you flash HTC rom, the rom contains os+radio+spl+....other thing ...
Try this method to downgrade your SPL (9.99) to oli 3.20 :
1°) run splxploit
2°)when the phone reboot on the spl 1.20 oli, run HardSPL 3.20 olipro. (search on the wiki or the trinity forum
3°)upgrade to 3.20 oli ...
Now, when you go to the bootloader, you can see SPL 3.20 oli.
Try reflashing a radio only (see the upgrading topic, you will see radio 1.56.xxxx)
Tell me if this method work.
When i'm on spl 3.20 oli, i can load radio rom to 0%
when I downgrade my phone to spl 1.05, and i can run the upgrading to 7% (best score )
To downgrade to SPL 1.05:
edit the "unbrick.bat" on the splxploit folder.
Replace TRIN_HardSPL.nb to TRIN_SPL105.nb
try to find SPL 1.04. I'm sure if i got the spl 1.04 i can revive the phone
Did exactly as you said final result:
When i'm on spl 3.20 oli, i can load radio rom to 0% (and stays there )
hi,
ok, try to load spl 1.05 with splxploit, and when it is load, run radio upgrade (1.56.xxxx)
Try to find spl 1.04 and mtty it can be reset the radio bootloader
if you find 1.04, give me it
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
macars said:
hi nyco,
I tried with SPL 1.05 the result is the same as your reaches 7% and restarts. I'm still trying to find SPL 1.04 I found one for Hermes I tried but didnt work failed.
Click to expand...
Click to collapse
arf :/
You got exactly the same problem i have.
did you check if you have bad block (with mtty)
try format the phone with mtty.
i contact pof, but he doesn't answer me
I recently upgraded to the official 1.93 WWE ROM (and new hard SPL), and now my screen flickers a lot when the phone is switched on. (The flickering starts at boot-up when the red writing appears at the bottom-right of the screen).
I have been able to solve it so far by pressing the power button twice to switch the display off and back on again, but wondered if anyone else had experienced this and could suggest a more permanent fix?
Thanks,
Neil
Most likely who hasnt experienced this.....lol
Anyway, when you get this after a reset, just turn on and off the display and all goes back to normal.
You need to flash another hard spl. The issue is caused by an outdated spl not being compatible to your lcd screen. Try hard spl 1.37 found here:
http://forum.xda-developers.com/showthread.php?t=400950
I want to flash
_QMR_RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
to my UK Vodafone Diamond which has SPL 1.37 from the factory.
Which Hard SPL should I use - 1.37? Signed or unsigned?
djvw said:
You need to flash another hard spl. The issue is caused by an outdated spl not being compatible to your lcd screen. Try hard spl 1.37 found here:
http://forum.xda-developers.com/showthread.php?t=400950
Click to expand...
Click to collapse
Thanks! I tried searching for "flicker", but got too many results and didn't find that thread.
i have the flickering screen too, i want to try this method but my activesync does not work. i try a hard-reset and now the device ask me to insert Getting STarted Disc to install synchronization software which I did. it still doesn't work. anyway to do this?
Thanks
i have the same problem i flashed the 1.93 hard SPL and still nothin... anyone know the problem?
i did managed to get the flikering out... flashed hard spl 1.38!
I want to try flash HardSPL but my USB port doesn't work, is there anyway to do this?
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
go to olinex hard spl section and write about your problem maby they can help u
Onlinex hard spl section?
I must be blind. Where is that?
matejdro said:
Onlinex hard spl section?
I must be blind. Where is that?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=431218
go here
matejdro said:
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
Click to expand...
Click to collapse
Just got that error yesterday while updating my Rom and OS go to Settings, Connections, USBto PC, then choose active sync and check enable advance network. You might need to reboot your host pc to recognize changes on you mobile device.
Tried both checked and unchecked and dont work
I have managed to solve it!
Problem was newer Stock SPL.
What i did is installed image that contained old 0.52 SPL and now i can finally install Custom ROMS
Great!!! I will remember that one too.
Hi there
I just bought a new Topaz. I have HardSPL and then tried to apply a new ROM. Now it keeps on rebooting - it only gets to the screen where it says TOUCH DIAMOND 2 - and the the red numbers appear in the lower right corner - and then it reboots..
Is it bricked or is there anything I can do??
I tried to hard reset - but it still keeps rebooting
No not bricked.
Must be an incompatible ROM or you didn't HSPL to 2.51.
Just find another ROM, Stock or otherwise (since you are HSPL'd, but check your version first), go into Bootloader Mode and flash with RUU.exe.
Thank you Bruce!!
I'm still having problems though. I have tried to install a few different stock ROM - both 6.1 and 6.5. Everytime the same issue - I get stuck on loading the new ROM and it keeps rebooting.
I have tried to upgrade spl to 2.51 but still the same issue
What else can I do??
What does your SPL show in bootloader mode?
Make sure it has Olinex as a suffix.
Thanks again Bruce,
Yes it says Olinex.. When I first got the phone I tried to install a new ROM and I forgot to do SPL first - could it be that something serious went wrong in that attempt?
Anything else I can try?
niknik76 said:
Thanks again Bruce,
Yes it says Olinex.. When I first got the phone I tried to install a new ROM and I forgot to do SPL first - could it be that something serious went wrong in that attempt?
Anything else I can try?
Click to expand...
Click to collapse
Is it 1.83.Olinex or 2.51.Olinex?
Flashing a ROM w/o HSPL will most certainly mess up your device but it should be recoverable if you can find your stock ROM for your carrier and region.
You symptoms sound as if you are on 1.83 trying to flash 2.51 SPL ROMS.
Hi, im having the same issue as OP, i tried to flash the latest Energy rom (sept 8) onto my td2 and the bootscreen is showing 1.83.Olinex. What do i do to fix this?
You must have HSPL 2.51 for this ROM and for all newest roms.