Related
Hi guys
i think my xperia is dead. when i turn it on it shows the logo for some seconds and it restarts and keeps on doing this forever.
How this happened.
I tried SEUS with vista stopped at 11%
tried mtty
set 16 0
task 14 0
boot
and the phone begin to restart in infinity
i installed a uk original rom but the spl remained still Olinex
i don't know how to return to original spl so i can send it to the warranty...
pls help!!!!
have you tried: http://forum.xda-developers.com/showthread.php?t=445662
informatico said:
Hi guys
i think my xperia is dead. when i turn it on it shows the logo for some seconds and it restarts and keeps on doing this forever.
How this happened.
I tried SEUS with vista stopped at 11%
tried mtty
set 16 0
task 14 0
boot
and the phone begin to restart in infinity
i installed a uk original rom but the spl remained still Olinex
i don't know how to return to original spl so i can send it to the warranty...
pls help!!!!
Click to expand...
Click to collapse
extra how to: how to restore Stock SPL for warranty reasons.
step by step:
- this is ONLY for warranty reasons. i.e. the device needs repair and you have to send it to htc to get it serviced. if you plan to restore hardspl then don't even bother flashing this stock package, unless you are some kind of hacker/dev
- IMPORTANT: be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
- now the steps
1. download the stock spl package from this post.
2. download X1_HardSPL_v1 too, from this post.
3. run the hardspl package, but do not press Next button i.e do not go ahead with flash yet.
4. at this point, take the extracted stock SPL, a RUU_Signed.NBH file, and overwrite the other RUU_Signed.NBH in hardspl package.
5. go on with the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to tricolour screen with 0.52.OliNex version), it goes to 100%, reboots, done.
+1. to verify, enter bootloader (see description above in this post), and check version number on tricolour screen. it should say 0.72.0000.
Click to expand...
Click to collapse
Found it here, @ the end of the first post.
Thank you for all your help
well after not sleeping all night yesterday now it's working
i don't even know how it began again to work
i did a flash of a stock rom it stopped at 10% then a hard reset (didnt work initially) then flashed again hardspl and it could do the hardreset.
im si happy it's working again
i don't count that much on se warranty
thanks again
Sometimes the problem is in the incompatibility of Hard SPL with your ROM. Same happened to me with Diamond. Only flash another rom and problem solved
informatico said:
I tried SEUS with vista stopped at 11%
Click to expand...
Click to collapse
I have the same problem and I must install windows XP in another hard disk for install the x1 software...
clecle69000 said:
I have the same problem and I must install windows XP in another hard disk for install the x1 software...
Click to expand...
Click to collapse
If you can find the dowloaded .nbh file on your machine, you can copy it to your microSD card, rename it to Kovsimg.nbh and flash from bootloader that way.
However I couldn't find where the SEUS was saving the file.
Well my problem was very strange because i could flash the firmware through microsd or RUU successfully but it didnt boot. It just showed the logo for some seconds and rebooted again. I also tried many commands with mtty like task 28, task 2a (which make it just appear a white screen and nothing else). anyway the only thing to make it work was to hard reset and then flash the hardspl again...
after flashing the hardspl the hardreset began normally.
Does anyone know how to do the hardspls - Yes it should go to tricolour screen now and say 0.52.OliNex.MFG (this is SSPL!).
but then the error message is coming and no
"Hard-SPL flashes, device automatically reboots, job done"
I got a Upgrade ROM code error, please try again.
any ideas on how to get this to go away and return to my phone?
Hard resets dont work
I have tried the other things listed from the other "I bricked my phone"
Unluckily I'm using Vista and currently don't have an XP ready computer to use. I've removed the battery and plugged the USB cable in and I still get the TRI colored screen with no connection to Windows Mobile Device Center
I did notice that with the memory card installed, the TRI colored screen does go away for a second, but goes into a Loading... and that's all the phone does
from my experience tis happened when the hspl didn't flash correctly. my best suggestion would be to try flashing hspl following the instructions for vista, though it may be easier on xp.
btw, the boot looks for an image on the sd card to flash that's why you get the different behaviour.
i'm not sure if it's possible to flash hspl via the sd card only.
Thank you for the advice
I will try and execute that, but im pretty sure it wont work. the phone wont even connect with my computer
?
when trying to connect to your pc, is it in bootload? if not try that (vol down & power same time till boot screen appears). once you connect it should show in the white area the words "usb" after that try running the ruu.
problem solved!
apparently I didn't realize that I was on the stock 1.14.0000 SPL and that I had to flash the stock rom...
I then flashed the stock rom and re-did the SPL to the Olinex one and re-flashed a cooked rom
Thanx for all the input fellas
I have been reading through this forum and ppcgeeks but I suspect I am doing something wrong.
My HTC Touch Viva is stuck in bootloader mode.
ONBL 1.26.0000
SPL 1.26.0000
Here are the things I tried:
1. Downloaded HardSPL, I get the 1% straight to 100% error 270 update error. I am figuring that I cannot install this when in bootloader mode.
2. I get the hardspl .nbh file and rename it to OPALIMG.nbh and put it on the SD card formatted in FAT32 and get Invalid Certificate error.
3. I tried downloading the stock rom, and windows 6.5 rom and I get the same error 270.
I tried these same things on my wife's htc touch viva and I managed to update the SPL and WM fine but I am in Windows Mobile and activesynced vs stuck in bootloader mode.
What am I doing wrong?
nicksti said:
I have been reading through this forum and ppcgeeks but I suspect I am doing something wrong.
My HTC Touch Viva is stuck in bootloader mode.
ONBL 1.26.0000
SPL 1.26.0000
Here are the things I tried:
1. Downloaded HardSPL, I get the 1% straight to 100% error 270 update error. I am figuring that I cannot install this when in bootloader mode.
2. I get the hardspl .nbh file and rename it to OPALIMG.nbh and put it on the SD card formatted in FAT32 and get Invalid Certificate error.
3. I tried downloading the stock rom, and windows 6.5 rom and I get the same error 270.
I tried these same things on my wife's htc touch viva and I managed to update the SPL and WM fine but I am in Windows Mobile and activesynced vs stuck in bootloader mode.
What am I doing wrong?
Click to expand...
Click to collapse
Turn off your Device's Security, so your warning won't come up and disrubt the process.
How do I turn off the security? I cannot get into the phone.
Actually I tried to drain the battery, hard reset, RUU attempts and once the phone actually started to boot (I do not know why) but this is what it did:
It showed a screen with two tabs at the top - System and Ring. It kept making a funny chime and highlighted the tabs back and forth while a bar was moving across the screen near the bottom (like an installer bar). Then it rebooted and stuck again and I have not been able to get it back to at least attempting to boot windows.
Any idea?
nicksti said:
How do I turn off the security? I cannot get into the phone.
Actually I tried to drain the battery, hard reset, RUU attempts and once the phone actually started to boot (I do not know why) but this is what it did:
It showed a screen with two tabs at the top - System and Ring. It kept making a funny chime and highlighted the tabs back and forth while a bar was moving across the screen near the bottom (like an installer bar). Then it rebooted and stuck again and I have not been able to get it back to at least attempting to boot windows.
Any idea?
Click to expand...
Click to collapse
Go to BootLoader and try i guess
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Exa777 said:
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Click to expand...
Click to collapse
Try to reflash the rom you was flashing in the first place.
Mayb it is locked, cause it needs a serten file from that rom.
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
ted presley said:
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
Click to expand...
Click to collapse
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Exa777 said:
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Click to expand...
Click to collapse
try agent47´s task29 that might help
Im trying atm...so far its been 10mins and its stucked at 0%....i cant flash anything =(
Edit... it Gave me update Error 262
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
I Hope this help you!
In one occasion I suffered a similar problem and the issue was that the Memory Card was damaged, and when the Phone Start and tried to read this it "stuck" reading this.
Try to start the phone without the memory to see if this work.
Regards.
Musse_1 said:
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
Click to expand...
Click to collapse
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Exa777 said:
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Click to expand...
Click to collapse
I've had it.... here is the list of everything i've tried
Mtty /Task 14 0 , Task 28 55aa , task 8
Flashing SD Method
Flashing Stock Rom /Sd Method
Flashing Another Stock rom /SD method
Flashing HardSPl back and for from stock to olinex 72
Using Seus Updater
Take out battery out of the phone for 24h+ to (reset it)
Used Task 29...with no sucess...
Flashing using Cuu Firmware or whatever its called....failed
Every single time i try to flash it goes wrong ... for stock roms it stop at the OS part
Anyways Seus updater put me on spl78..but fails when it comes to the OS @(15%) Like
I just need to Fail Flash one of the Stock rom to go back to spl 0.72
my question is is there any hacked/cooked rom wich include HardSPL like the stock roms does?...that would like flash my bootloader?
Any other suggestion would be greatly appreciated...i dont wanna throw my Xperia Away..when it still can boot in bootloader...i refuse to believe X1's Bricks that easily (ONLY 1 BAD FLASH )
Phones current situation: has no OS, Cant charge it , it turns on itself whenever the USB is plugged in
HardSpl wont flash whatever what i try...so im stucked on Stock SPL eitheir 72 or 78 ..that i can still choose
Phones MicroSD methods keep saying OS fail , (0018003)
Likewise with stock Roms
Mtty...didn't do ****!!!! yet it i got the log like if went trough alot and ****....
lolSEUS Updater get stuck at 15% after updating the bootloader.
Help?
hi guys, i have a problem, ive tried to instal new rom with hard SPL and i had some error during instal, so i canceled it... then my HTC rebooted and is stucked on HTC screen (after circa 15 sec appear in down left corner R, G, D with some nubers and thats it, help me please
bissqit said:
hi guys, i have a problem, ive tried to instal new rom with hard SPL and i had some error during instal, so i canceled it... then my HTC rebooted and is stucked on HTC screen (after circa 15 sec appear in down left corner R, G, D with some nubers and thats it, help me please
Click to expand...
Click to collapse
Please provide better details.
What does your Bootloader screen show for SPL? (Soft reset phone and hold Volume Down before boot starts until you get to tri-colored screen)
1.33.00 or 1.83.Olinex, or?
here is the photo
ttp://i128.photobucket.com/albums/p188/Bissqit/IMG_8156.jpg (remove the space, i cant post links)
and in few mins i give video, how phone behave when i turn it on
bissqit said:
here is the photo
ttp://i128.photobucket.com/albums/p188/Bissqit/IMG_8156.jpg (remove the space, i cant post links)
and in few mins i give video, how phone behave when i turn it on
Click to expand...
Click to collapse
I am at work so I cannot access photobucket.
Can you please just tell me what it says?
so
TOPA200 32M
SPL-1.33.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW (these are in red)
TP MFG DATA
500,542 175,869
188,210 816,201
813,880 Calibrated (in green)
Serial (in white)
bissqit said:
so
TOPA200 32M
SPL-1.33.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW (these are in red)
TP MFG DATA
500,542 175,869
188,210 816,201
813,880 Calibrated (in green)
Serial (in white)
Click to expand...
Click to collapse
Where it says SPL - 1.33.0000, if you successfully HSPL, it will say 1.83.Olinex.
I suspect you didn't verify your SPL flashed correctly before you attempted to flash the ROM? If so, this is not good.
Hard reset (Reboot phone and hold both Volume Keys before device starts to boot, and continue holding them untill you get to the white screen, then follow the prompts.)
If you can get back to stock with a hard reset, I suggest you go here and do some reading.
If it gets stuck at the same screen, you will need to find your stock ROM. You can hopefully find it from HTC's site with your Serial Number.
Once you get your stock ROM, connect your phone to your PC and go to Bootloader. Once it displays 'USB' instead of Serial, run the .exe for your stock ROM.
i tried to dl stock ROM from HTC.com, but it says:
Sorry, this software download is not suitable for your device.
im not sure if im on the right side, but there are only 4 options...
i downloaded original update, but from other side and while phone was connected to PC with Red green blue screen i opened the RUU everything went good until status bar (on PC and phone appeared status bar with % as it started installing, but then error) :/
So hard reset was unsuccessful?
Try flashing from SD card.
Right click on the Stock ROM and Extract to a folder.
Place the ruu_signed.nbh file renamed to TOPAIMG.nbh on the root of your SD card and then enter bootloader.
This will initiate the flash and hopefully it won't get stuck at 0%
You can also do this with the .nbh file from hspl.
Perhaps you should try to do HSPL .nbh first, because your OS is locked, it will ONLY accept the exact replacement ROM.
Also, I would suggest taking some time to read and learn about this stuff before diving in head first.
The link I provided previously is very thorough.
Take a look at the MTTY thread after you read about flashing and HSPL.
in bootloader it flash for 0,1 sec and says "Unable to load imagefile" or sth like that
bissqit said:
in bootloader it flash for 0,1 sec and says "Unable to load imagefile" or sth like that
Click to expand...
Click to collapse
Make sure it is 'TOPAIMG.nbh' exactly without quotes.
What was the error you received when you attempted from your PC?
its exactly like that,
it can be any ROM? becouse i have rom with nbh + exe files and with nbh only
bissqit said:
its exactly like that,
it can be any ROM? becouse i have rom with nbh + exe files and with nbh only
Click to expand...
Click to collapse
No, unless you get HSPL to flash first.
If you successfully installed a ROM, it would not boot up because your OS is still locked.
Use this .nbh which is for HSPL 1.83. If you can get this to flash, do the same with HSPL 2.51, then you can flash to any ROM.
i think im lost.
can you please explain me, what should i copy to my SD card and what to do (in oredr)
thanks
bissqit said:
i think im lost.
can you please explain me, what should i copy to my SD card and what to do (in oredr)
thanks
Click to expand...
Click to collapse
Download the SPL 1.83.zip and extract the .nbh file.
Rename it to TOPAIMG.nbh and place on SD card
Enter bootloader mode and pray.
With luck, it will complete to 100%
Then you go back to bootloader and VERIFY your SPL says 1.83.Olinex. (This is the step you skipped before you attempted to flash a ROM, and you have bricked your device as a result)
Without luck, it gets stuck at 0%
Then you need to read up on MTTY to recover your device.
If you think you have your EXACT stock ROM, you can do the same with the .nbh file you extract from that, as previously instructed and get back to stock first before worrying about HSPL.
Basically HSPL unlocks your OS to be able to accept updates. Without it, you can only update from the stock image.
So your choices are, to try to HSPL, or try to get back to stock. Both can be done the same way, in bootloader using respective .nbh file.
I think you are looking to shortcut this stuff and it will only lead you to headaches, unless you take some time to read and learn.
Now, you never did answer;
Did you attempt a hard reset?
What was the error you received when you ran the RUU from your PC?
so i renamed that file, put it on card, card to phone, pushed VolDown and turned on. It flashed with loading and then again "No image file" and back to boot screen
i did few hard resets
error when i tried that "official ROM" was that: Error 294: Invalid render ID
This update cannot be aplied on this device
i try older ROM
Alight, your 294 error indicates its the wrong ROM for your device.
No Image File indicates that bootloader isn't recognizing the file.
Make sure your SD card is formatted to Fat32, you may want to try a 2-4gb card just to be sure. Sometimes larger cards get errors.
Since you can't find your stock ROM, you need to get the HSPL.nbh to load first.
If you can get the 1.83.Olinex to flash, continue the same process for HSPL 2.51 .nbh file.
so i did everything dled you file, formated card, put your file on card renamed turned on phone and now its stucked on loading (if i made something wrong tell me) couse im not sure
i connected phone with pc and try to instal Topaz-HardSPL_V5_00R5_183HSPL but its stucked on 0%
bissqit said:
so i did everything dled you file, formated card, put your file on card renamed turned on phone and now its stucked on loading (if i made something wrong tell me) couse im not sure
Click to expand...
Click to collapse
Well, we got it to recognize the image which is good.
Sounds like you did everything correctly, it just doesn't always work.
I think you have 3 options here;
1. Try to find your stock ROM and flash either from PC in bootloader or from SD card.
2. Read about MTTY and how to use it to flash to your phone and recover, but I still think you need your stock ROM to do this.
3. Warranty return- just tell em it froze, don't mention what you have done to it.
I have one other thing we can attempt here.
Download the enclosed file and unzip it to your PC.
Connect phone to PC and go into bootloader, then run Task29.exe.
With any luck this will force it to load HSPL.
Let me know what happens.
i tried ROMUpdateUtility, task29everything seems to work, but alwways stucks on 0%...
úroblem is, that my phone isnt originaly mine, i bought it from one guy, (couldnt be problem that it is MDA Compact V?)