Database Develop

Did i just brick my phone? Help!!!

Hi, Well i came here and found WM6 install for the BA and so i go and try and install it, i think nothing of it. Then the installer comes up saying that it cant detect my phone so i go and look at my phone and Its just a gray screen with Serial at the top and V 1.02 at the bottom. Man, i just got this phone and im hopeing i didnt screw it up already =/ this freaking sucks. Can anyone help me please

Are you using USB port to connect your phone? If you are your usb connection is not working because it will show usb on the screen rather than serial. Need to check your usb connection if you are using usb.

Well, it says that when i got it conected to the dock, But serial when its off.

If it says that then the usb connection is AOK.
Hmm... You mean you havent installed it yet?
Try "Hard Resetting" then reDo the process of Upgrading step by step... maybe you missed something.
I think that as long as your bootloader is intact. You can install your OS definitely, I think, correct me if im wrong. coz that happened to me and i revived my BA.

Well it was just an installer, I ran the .exe and it was like "Installing WM6!!" then it just cut off and did this crap. So is there annother way to install it? did i do something wrong?
Well i tried "Hold down the Power button (Top Right corner) and at the same time put your Stylus pen in the hole where it says “Reset” (Lower Left corner)." But the screen lights up and then goes blank then it pops up with the serial jazz. I hope i can get this fixed because i cant afford a new phone.

Try pressing/hold the (Record Button) + (Power Button) Then Stick the (Reset Button)...
that'll make it go into the Interface Mode(Bootloader) that's either Serial or USB... then try to flash it again.

Well, I do that and the screen does the same thing, when i hook it up to the dock it does the famose xp Bedunk sound saying it knows something is conected. How do i install the thing again if active sync cant find it?
Okay, well i went to try and install it anyways and it seemed like it worked... why do i have such bad luck?
Well now after it was complete n i did the soft reset, It has 4 big bold Color lines, and at the bottom it says
No GSM
D 5.60.00 WWE
=/ whats that mean? Im too damn young for all this technical crap man, any help, please...

Hey xXBuddahXx
It-s all good... Just reset the device pushing the pin with the stylus and everything will be fine...
Anyway, like SilverSamurai said..., if you can get into bootloader mode then you're fine...
Make sure you upgrade using the MaUpgradeUt_noID app and follow carefully the instructions step by step: http://forum.xda-developers.com/showthread.php?t=326532
My first upgrade to another 2003 firmware was a nightmare and many times I've felt my heart pumping like it was gonna burst just looking at my beloved BA not booting... And since I think I installed almost every ROM I could get my hands on.
My advice, try again cos Helmi's WM6 Pro really rocks and it's the most stable I've seen so far...
Good luck,
Brice

Help Flashing My Phone To The Dutty Series

Hey Folks. I have a little dilemma. I purchased a tilt with the dutty series all ready flashed to it. One day i left the phone on top of my car and drove off. Well long story short. I bought a new tilt but it doesnt have the dutty series on it. Cant live with out it. Can anyone walk me thru the process becaue i tried it on my own and i keep gettin the RUU error 200. And im Stuck and dont kno what to do. If anyone can help plz let me kno.

search....
http://forum.xda-developers.com/showthread.php?t=433835

HELP
Ok Now Im Getting The Error RUU 262. it goes into the tri color screen then into the gray sceen with he percentage bar but it doesnt load. how do i get aound that.

Did thread help you when you searched?
http://forum.xda-developers.com/showthread.php?t=487020&page=2

Help me please, dead tytn2 :(

Hello guys, i really need your help!
My phone is so strange now, i have been using Ultimate-X.V9 -21054, but in last days, my phone has gone to white screen some times when i press to screen up sometimes everything is fine, but others not and my phone sometimes dont respond to my touch, and sometimes is a bit slow
Now i have flashed to RUU_Kaiser_HTC_PTG_3.28.410.0_radio_sign_25.83.40.02_1.65.17.56_Ship, during the upgrade my phone stay on tree colors, but on computer appeared the status bar! and everythime i turn on my phone now is like 90% is allways white :O i have open my phone, and reconected all again, but the problem still there! im using 3.34 hard spl!
Please someone help meee... i really love my tytn2 is there any way to put this fine? its hard spl problem?
Please help me

Please help meee My phone now is more slow than normal :/

That happened to me a while back, I took it apart several times and checked connections etc. but that did not fix it. I ended up buying a new LCD off of ebay which fixed it perfectly. So, I would suggest doing that (I bought one for 15USD used).

But this to me seems to be a problem on the main board, because the phone sometimes gets really slows And sometimes that white problem appears and others not, like 90% when i need to use my phone

Flash Stock ROM?
Did you flash if back to a OEM ROM? Did it work OK if you left it on the OEM ROM? I have used "Kaiser_HTC_ASIA_HK_WWE_3.34.721.2" as a OEM to upgrade from on many phones that I had upgrade issues with.

i think RUU_Kaiser_HTC_PTG_3.28.410.0_radio_sign_25.83.40. 02_1.65.17.56_Ship is an OEM rom isnt? :x

P4k1t0 said:
Hello guys, i really need your help!
My phone is so strange now, i have been using Ultimate-X.V9 -21054, but in last days, my phone has gone to white screen some times when i press to screen up sometimes everything is fine, but others not and my phone sometimes dont respond to my touch, and sometimes is a bit slow
Now i have flashed to RUU_Kaiser_HTC_PTG_3.28.410.0_radio_sign_25.83.40.02_1.65.17.56_Ship, during the upgrade my phone stay on tree colors, but on computer appeared the status bar! and everythime i turn on my phone now is like 90% is allways white :O i have open my phone, and reconected all again, but the problem still there! im using 3.34 hard spl!
Please someone help meee... i really love my tytn2 is there any way to put this fine? its hard spl problem?
Please help me
Click to expand...
Click to collapse
did you ask in the proper thread before starting a new one?

msd24200 said:
did you ask in the proper thread before starting a new one?
Click to expand...
Click to collapse
Lolol? and what is the proper thread? --' dont you see this is any rooms i have tried?

P4k1t0 said:
Lolol? and what is the proper thread? --' dont you see this is any rooms i have tried?
Click to expand...
Click to collapse
noticed when searching all your post that you went straight to starting a new thread for this instead of asking in on of the flashing threads. http://forum.xda-developers.com/showthread.php?t=533976

Dude, and in what that link will help in my problem? if search on it, you will find the solution to my problem? the answer is NO, maybe you should read a bit better!

P4k1t0 said:
Dude, and in what that link will help in my problem? if search on it, you will find the solution to my problem? the answer is NO, maybe you should read a bit better!
Click to expand...
Click to collapse
dude the answer is yes go ask in the flashing for newbs thread, or one of the other great links in the thread i posted. maybe you should read better the rules about starting new threads because you are having a flash related problem that needs to be asked in a thread already setup to deal with flash related matters instead of starting a new thread.
have you tried pushing the hard buttons to get into bootloader? do you think MTTY may help your current problem?

msd24200 said:
dude the answer is yes go ask in the flashing for newbs thread, or one of the other great links in the thread i posted. maybe you should read better the rules about starting new threads because you are having a flash related problem that needs to be asked in a thread already setup to deal with flash related matters instead of starting a new thread.
have you tried pushing the hard buttons to get into bootloader? do you think MTTY may help your current problem?
Click to expand...
Click to collapse
Dude i can enter on bootloader yes, can i use my phone yes! but the problem is that sometimes (i mean, like all the time) the screen stay white when i turn it on, and the phone stays slow!!!!

jsgjm said:
Did you flash if back to a OEM ROM? Did it work OK if you left it on the OEM ROM? I have used "Kaiser_HTC_ASIA_HK_WWE_3.34.721.2" as a OEM to upgrade from on many phones that I had upgrade issues with.
Click to expand...
Click to collapse
i have tried that rom too, but nothing the problem is here

It sounds like your Screen is on the way out. I would replace it.
No lets play nice. Or Ill break out the fish heads lol

zelendel said:
It sounds like your Screen is on the way out. I would replace it.
No lets play nice. Or Ill break out the fish heads lol
Click to expand...
Click to collapse
Well, if is about the screen, i can say im safe :x
But one thing on my mind, the white screen i could say to change the screen to one new, but the problem is the kaiser stay a bit slow, and sometimes it dont respond to what i want!
With that stay thinking that the problem is about the mainboard or something like that :s but i hope the problem is the screen, i will buy a new on ebay

The ribbon cable for the digitizer (touch screen) attaches to the LCD, and then both signals feed through the same cable into the D-pad board, so its possible that there is a bad connection somewhere in the LCD/Digitizer assembly that causes it to not sense your inputs, even when the LCD itself is working. Mine just failed completely to a white screen and did not come back. It could be something besides the LCD..try flashing a new HardSPL and/or a different ROM, but if I had to bet, I would bet on the LCD.

zelendel said:
No lets play nice. Or Ill break out the fish heads lol
Click to expand...
Click to collapse
Thankyou made me chuckle

P4k1t0, I know you're frustrated that you phone doesnt work, but do not get uppity at the other forum posters. If you sound off against msd24200 and a mod sees it, its likely to lock your topic.

i had the same situation two weeks back after i flash with my own cooked rom.
what i did is flash the stock rom through SD/storage card and everything is fine.
you already try this method ? you can search on how to flash from SD/storage card

to flash by sd card? ok ok i will try it right now to see

htc tytn II touch screen doesn't work.

Hi all
I have problems with the TyTN II touch screen works when i start but after few minutes it no longer works
worked well but I found it like that I ran off the battery and after i powerd teh device the touch screen wooden't work
i fash it again and it worked fin for a few minutes and after it don't
i have hard reset the pda but with no succes
please help me

Screen Problem also
that's my problem too haizt! is there anyone can help us with this problem?

Have you tried another battery and see if that is the problem?

yes I tried
is the same the thing is that after I installed the new ROM works well and after a few minutes dosen't work at all
please give me a solution

please help
i realy need the phone

please help

blu_bugsy said:
please help
Click to expand...
Click to collapse
Did you hard reset your device? Try that and see if that can solve your problem.

yes i did that but nothing happened
after i install the new ROM the touchscreen works for a few minutes then it's dead.i tried to install the hard spl but it keeps disconnecting.
please give me a solution
i'm dead without my phone my work depends on it

please give me a solution
i'm dead without my phone my work depends on it

blu_bugsy said:
please give me a solution
i'm dead without my phone my work depends on it
Click to expand...
Click to collapse
Have you even check if your sim door lock...is ok?. Can you get into bootloader and flash another rom.
I have the feeling your problem is hardware r u still in warranty?

please help
yes its locked
yes i can but it keeps disconecting when screen loading starts
the original rom iti instaling fine butthe hard spl its keeps disconeting and not finising the instalation process
if iti a hard problem how its work fin when i instal new rom and if it stays closed it work when i power on for a few minutes i dont think its hard problem but i dont know what to say
it's not in warranty
i really dont know it happend with him it worked perfect in one night i runn out of baterry and in the morning i find it in the welcome windows screen tab screen to continue and after that it stop working i dont really know what could happend

i will not give up until i have a solution for my problem
please help me

Still sounds like the battery to me.
Did you try a new, fully charged battery ?

blu_bugsy said:
yes its locked
yes i can but it keeps disconecting when screen loading starts
the original rom iti instaling fine butthe hard spl its keeps disconeting and not finising the instalation process
if iti a hard problem how its work fin when i instal new rom and if it stays closed it work when i power on for a few minutes i dont think its hard problem but i dont know what to say
it's not in warranty
i really dont know it happend with him it worked perfect in one night i runn out of baterry and in the morning i find it in the welcome windows screen tab screen to continue and after that it stop working i dont really know what could happend
Click to expand...
Click to collapse
Are you sure you are following this to flash your phone or hardspl? http://forum.xda-developers.com/showthread.php?t=433835

i have bought a new battery but noting happend still not working
i have read the post a thousand times i had followed every step but it still disconnecting when the loading screen at 0% appears
i think i a need a new touch screen but in romania i can't find something like that
please help me i really need the phone

blu_bugsy said:
i have bought a new battery but noting happend still not working
i have read the post a thousand times i had followed every step but it still disconnecting when the loading screen at 0% appears
i think i a need a new touch screen but in romania i can't find something like that
please help me i really need the phone
Click to expand...
Click to collapse
If you are getting stuck at 0% maybe you had a wrong hardslp flash. Read these threads, they are experiencing about your problem http://forum.xda-developers.com/showthread.php?t=433835&page=52

Hi
I have also problem with touch scree, about couple of weeks ago it started not to aim very well (eg. i touch the place and the responce was about 5mm in the other place) but i was recalibrating my screen and for a few days it was working fine, than another calibration and another, after that that was a time when it started not to work at all for for eg. 2 days, than it worked for a while and now it's not working for about 3 weeks.
I need to change whole lcd + digitizer or just digitizer (how to check it?). Should i change it by myself (i don't have those little screwdrivers) or take it to professional service (but they usually say they won't do it whith parts from ebay bcs they'r not original.
Please help

Have I destroyed my new Bell I9000M? RePar with PIT but no PDA.. IDIOT I AM!

**Phone seems to have no power does nothing, pull battery same thing cant even get download flashing screen screen**
I bought my new Bell I9000M and loved it then started about rooting, purchased rom manager premium and download darky rom 9.5 thru it and installed it worked pretty good.
Now I upgraded to 10.2RE and ran it for about 2 weeks without problems then today I started playing with emulators. Played SNES all day then noticed N64 installed played zelda no problems then found a psx emulator.
This is when disaster struck. I went to play FFVII with the psx emulator and it would lock up then quit the program. So I thought if i just did a reboot it might work.
Apon rebooting I started getting Force Close on pretty much all apps.
I tried to just repeat the install procedure for 10.2RE with odin including to make sure the repartition option was checked and it would load up then say something about UID inconsistent so I retried about 3 times (seems like it wasn't actually repartitioning then installing the clean software).
Frustrated I rebooted my PC and redid the process clicking the repartition then like a F'n Tard only loaded the PIT and not the PDA!!!
So no power
recovery botton method not working
tried vol down+power, vol up+down+power, just power (all with battery pulls)
the thing doesnt blink, cherp, or squat
I think Im done but pleeeease someone have something for me to do I am not a noob in these kind of things but it just came down to not double checking before hitting start.
Do i have a $400 paper weight and need to save for a S2???

http://forum.xda-developers.com/showpost.php?p=14957283&postcount=1
Sounds like you are gonna need to try and make a jig or grab one off ebay, if that fails then, you can always try a repair shop, if you are in the GTA I can recommend a place to you, they have a JTAG

Yeah I think its a JTAG repair at that point which involves a lot more hands on (search youtube - they have demos).
Graham

Well Im reading that I need to jtag.. Ive done this with satellite receivers before but my usb equipment is different then what all the youtube videos are showing.
From what I read I have a full/hard brick
I'm I wrong in that a jig will only fix a software brick (or does this classify as such) I can easily make the jig which i will attempt tomorrow but I just want to know if its worth my time as i read that a jig only works when u have a black screen with two little white boxes showing or something like that
Im in Edmonton, AB Canada can anyone help me out with a jtag? (If a jig is going to work then let me know to as Im waaay to tired right now!)
thanks for the help

evilgenius2309 said:
Well Im reading that I need to jtag.. Ive done this with satellite receivers before but my usb equipment is different then what all the youtube videos are showing.
From what I read I have a full/hard brick
I'm I wrong in that a jig will only fix a software brick (or does this classify as such) I can easily make the jig which i will attempt tomorrow but I just want to know if its worth my time as i read that a jig only works when u have a black screen with two little white boxes showing or something like that
Im in Edmonton, AB Canada can anyone help me out with a jtag? (If a jig is going to work then let me know to as Im waaay to tired right now!)
thanks for the help
Click to expand...
Click to collapse
Ahh right I just noticed the part where you said you have no power.... I dont think the jig will work for you in that case...

Just checked kijiji, you can call these guys and see if they have a JTAG
http://edmonton.kijiji.ca/c-buy-and...-Appointments-Free-Loaners-W0QQAdIdZ237786905
http://edmonton.kijiji.ca/c-service...es-Best-Prices-Guarranteed-W0QQAdIdZ218015698

So after much searching I have not found anyone in Edmonton who provides jtag flashing in town. If I was in Toronto I would be set.
Anyways since no one provides this service in Edmonton I feel like I should purchase the equipment and start providing this services.
Does anyone know what software and jtag I need to get and I reputable site to order off of?

evilgenius2309 said:
Frustrated I rebooted my PC and redid the process clicking the repartition then like a F'n Tard only loaded the PIT and not the PDA!!!
Click to expand...
Click to collapse
Not that I have a fix, but that use to be a semi normal step about 10 mos ago installing firmwares, to do the pit by itself, I hardly would think that step caused your problem... I could me misguided. This is the first post I have read with this issue though...

There is a user on the east coast that was about to get one before I convinced him to try warranty first as they were still all under a year old. Which you might try too...
Brisk something was his handle. Check back in my posts late July maybe...
Sent from my GT-I9000M using XDA Premium App