Hi everybody.
I searched but did not found answer to issue I having.
If I turned on BT my bt headset (A2DP) works fine, but on incoming call there is no ring sound on telephone speaker. When I checked phone i could see that is muted. My wild guess is that phone sends everything to headset because it is in A2DP mode and send every sound through BT.
How to fix this?
Headset?
Is your Bluetooth headset designed to handle calls as well as music? If not, that will be your problem. When I'm listening to music via BT headset, the phone rings through the headset, not the device speaker
grahamkdt said:
Is your Bluetooth headset designed to handle calls as well as music? If not, that will be your problem. When I'm listening to music via BT headset, the phone rings through the headset, not the device speaker
Click to expand...
Click to collapse
My bt headset is designed to handle calls.
http://www.sonyericsson.com/cws/products/accessories/overview/hbh-ds220?cc=CA&lc=en
What I want is to hear ring signal through device speakers as well as I don't have all time earpieces in my ears and I can miss a call
Related
OK!
I feel stupid.
I am running a Tilt and a Jawbone headset.
With the bluetooth on, the ring tones go through the Jawbone. How do I make them go through the phone's speaker instead.
I did read a thread about this issue someone else had, but it was with a stereo headset, which the JB isn't
Thanks!
I feel stupid too - I have the opposite problem. The Bluetooth hands free in the car doesn't ring on INcoming calls... just the Kaiser rings (and if its in my case I don't hear it)
I guess its a setup issue - any suggestions?
Graham
Is it possible to have the Tilt on Vibrate mode and still have the stereo Bluetooth audio active? If I'm listening to my headphones, surely that means that I'm in a place where I don't want to have the phone ringing or alerts sounding off on the phone....
I'd like to have the phone in vibrate mode and all audio piped to my Jabra BT8010. However, when I move the volume sliders down and set it to "Vibrate", I lose headphone audio. Am I missing something?
Curtis
Since all audio is now in your ear, you don't really need vibrate as you will hear the ring in your headset as well as any other audio..... There may be a reg tweak to get vibe and ring but I don't really see the point.
RemE said:
Since all audio is now in your ear, you don't really need vibrate as you will hear the ring in your headset as well as any other audio..... There may be a reg tweak to get vibe and ring but I don't really see the point.
Click to expand...
Click to collapse
The issue is that my phone still rings (loudly). If I'm using the headset, I don't want my phone to ring. If I turn my phone to vibrate, I can't hear any BT audio (ie. no music in the stereo headphones).
What I want is to have my phone silent and still play music broadcast via BT to the Jabra BT8010.
Curtis
I see, I didn't notice this. When I've been using the vibe toggle button while in meetings, I can use the BT headset and hear rings in it and get voicemails etc. I just didn't try to listen to any other stored content, hmmm.
rutilate said:
The issue is that my phone still rings (loudly). If I'm using the headset, I don't want my phone to ring. If I turn my phone to vibrate, I can't hear any BT audio (ie. no music in the stereo headphones).
What I want is to have my phone silent and still play music broadcast via BT to the Jabra BT8010.
Curtis
Click to expand...
Click to collapse
If you go to phone settings, your able to send incoming calls to vibrate, thus allowing other sounds to work as well.
Settings -> Personal -> Phone -> Ringtype -> Vibrate
I am using the bluetooth headset with the phone but when bluetooth headset is connected and a call comes in it is going straight to my headset i cant hear the phone ringing i can only hear if i have the headset on
can i change this someone how ?
I just wanted to buy a stereo bluetooth handsfree for my device and finally I decided to buy an EverE T909s about 40 $...
it pairs correctly and fully to the device and music sound is good... but when there is an incoming call or when i call some one its microphone is so weak and people cant hear me!
I just paired the headset to another phone but it worked properly...
any solution?
I have the same problem. But in my case people can hear me when T909S is connected to the phone (Samsung), not very good, but they can.
What I'm concerned is when I connect this headset to my computer and try to use it for Skype, whatever settings I use the sound from Microphone is always very squeaking and it's impossible to use this headset as my headphones in Skype...
Any solutions?
When making calls with the bluetooth headset, the headset switches in the call-mode, but sound is not working. Both microphone and speaker. I've tried it with 2 different headset and both worked with my previous phone.
Playing music over bluetooth works flawless.
paul70078 said:
When making calls with the bluetooth headset, the headset switches in the call-mode, but sound is not working. Both microphone and speaker. I've tried it with 2 different headset and both worked with my previous phone.
Playing music over bluetooth works flawless.
Click to expand...
Click to collapse
Is the Audio from calls enabled in your bluetooth profile of that connection?
Is this your only bluetooth connection at that time? Mine is able to connect to 2 bt audio devices at the same time, making both unusable, no matter what i do. As soon as i disconnect one connection it starts to work again.
Bluetooth handling seems to be bit glitchy atm