Hi @ all !
There´s a thing very annoying in the new Kaiser... You cannot use any belt-pocket with magnetic closers !
After setting the phone to standby via one short press on power button, I found it back turned on again, everytime I took it out of the belt-pocket.
First I thought, that this must be the keyboard slide mechanism, cause the phone also comes back, when you slide out the keyboard, but I kept an eye on it, not the move the slider while putting it into the pocket and back out again. Then I thought, that it was the light sensor, but some tests made me sure, that it must be something else.
Finally I found out, that it turns back on again, cause I´m still using the belt-pocket of my old TyTN I with the 2 magnets as closing mechanism... If you try and hold a magnet over the keyboard in the area of S,D,E,X,F or even on the back side in the same area and move it around just a little bit, the phone turns on... Crazy, but true !
Now I know, why they gave that awful new belt-pocket with the tape-closer to the Kaiser...
Hope that helps
Marco
It is partly related to keyboard... it has a magnetic sensor that it is activated when keyboard is released, so the magnet from your holster tricks the sensor into believing keyboard is out, so it activates screen.
I guess thats why they have the velcro closer on the one that is shipped with the phone. This is somthing to consider when buying a nice Piel Frama one.
Absolutely it's the keyboard magnet operated switch that does it. But, I know you can run a magnet (let's say the case magnet ) over the d-pad area (seems to do it on mine) and the Kaiser will turn on. - However, I have been using the TyTn case also and I have not noticed it turning on just by sliding the Kaiser in and out. In fact I have just sat here and put it in and out every which way (for the last ten minutes) and it has not come on.
Maybe your magnets are stronger than mine or your keyboard switch more sensitive? I am also not keen on that "tape" closing on the new case.
Mike
lol i wish i would have read that some place, i thought it was the keyboard some switch but didnt think they would use a magnet, it was pissing me off a lot while i was driving, now i know i found on my own, but the magnet that i have is shielded a bit, but still just the right position and it will trigger the switch
I sure hope this was posted some place in a FAQ or wiki, if not it should be and if it was, then shame on me for not reading that part or noticing it
Magnetic sensor via magnet in holster.
Just found out this "feature" with a BB holster...
Has anyone found a way to exploit/use this feature to turn-on the device when removed from the holster?
That is something I always envied with my wifes Blackberry.
I've noticed this too
I have the same problem, but since mine is set not to wakeup when the keyboard slides open I can't see how the magnet could be the culprit.
I had the same problem with my Nokia and Kaiser.....Never thought it was because of the magnet sensor in the device....To tell the truth...I didnt know that it had one inside.....Thanks for the info....
Would it affect the sensor in anyways....if it doesnt, I can actually use this "feature" so my phone is awake each time I pull it out of the belt case......
I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?
Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?
I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim
when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers
Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?
Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?
iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!
Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here
Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff
mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.
try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?
you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")
thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work
I have a Tilt that will not switch to landscape mode when I slide the keyboard out. The light won't come on like the sensor is not recognizing the event. Is the switch mechanical or magentic? Is there an easy fix for this?
it is magnetic, to the best of my knowledge. i think there were some threads/posts about how to be sure your magnet has crapped out and/or has become misaligned...
can't quite post the links to those threads but a google initiated search within the xda forums might just give some meaningful results.
Well it looks like the sensor is out. I have a working Tilt and I can take a magnet and slide it around and it will flash to landscape. But the broken one does nothing. Anyone know where the sensor is and what it looks like and how to replace it?
Anyone? Where is this sensor and is it replaceable?
recently phone screen is acting kinda weird...
well the problem is when i slide it up, only the 'X' tab or button only works. Other menus in the screen dont work like it should be...
when i slide it down works perfectly fine.
any ideas regarding the problem? Thnx.
since with the ba there is no actual sliding function, you know, the device does not really realize it was slid open unlike other sliding phones, i'd guess this would have something to do with the digitizer or the internal flex cable. maybe it gets strangled, when slid up, if i were you, i'd probably avoide sliding it, before the cable maybe gets cut or torn apart, you should very carefully open it up and look whether there is something strange or wrong with the inside of your device.
the procedure how to get inside the device you can find in the official service manual, to be found here: http://www.4pda-service.ru/netcat_f.../BLUE ANGEL/HTC_Blue_Angel_Service_manual.pdf
Hey folks,
Just a quick question for anyone that would know. Does anyone have any idea where the keyboard backlight is located within the G1? I have the service manual but it doesn't say anything about the keyboard backlight. Mine has not worked correctly for months (blinks/stutters on and off or stays off completely) and it's a pain to use the kb w/o the backlight.
I'd like to see if there's a torn ribbon, or a wire that's not making contact, to try to fix it, but I need to know where exactly inside the phone is the light. Anyone that can help, I'd really appreciate it.
Anyone? Bueller??
I guess EVERYONE'S keyboard backlight works fine eh?
If its defective why not send it back in to T-mobile?
Also, there may more than one light.
I'd imagine it's a series of SMD LED's.. if the whole thing flickers it could be a damaged ribbon, but if only one side flickers its probably a dry solder joint or something.. you haven't got much hope of resoldering an SMD LED if that's the case.