Greetings Dears,
Please help me, my X1 giving me only tri color boot screen, i tried soft reset many times, i tried hardreset and it didnt work, i removed the battery for a long time and when started also giving me the same !! i did Hard SPL before, i tried also upgarding the Radio ROM through SD card and it gives me Update Complete and Success and tried to reset it but also gives me the same boot loader image!!!
What should i do? i need to access the device for the data, i have a lot of info i need to retrive fom there...is there any one can help?? Please how can i get out of the Bootloader screen
Thanks
Ash
More Info
By the way, i have the following info on the screen
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
Regards
Ash
If you have made a hard reset, data on your phone are lost (except data on your SDcard)
Try to flash a new rom trough SDcard
Thanks, here is the point i dont want to flash the ROM because i dont want to lose the data, i just tried the manual Hardreset to test if the device will get into the H/R menue , but it didnt!
Can you help in why this happend? and why nothing except the bootloader appear? i turning crazy about the data
Thanks
Guys,
Tried flashing using the SD card, after finishing i did a soft reset using the stylus and again it boots into the boot loader only
Help Pleeeeeeease
Thanks
RIP my toy ?
Hello All,
Since yesterday , my device always display during boot boot: Press SEND to restore factory default, press END to quit
I all tested:
enter in bootloader mode : color screen display during 0.5 sec before come back to "Press SEND....
perform hard reset : same as above
soft reset : same as above
if i choose SEND or END it's same , my device come back always finally to Press SEND ...
is there any hope ? last trick to try ?
Thanks
EDIT : after remove and put in my batterie a lot of times (more than 20 times) , my device lived again and boot properly
i flash for a more recent ROM , i will see
the old one was the first go out under WM 6.5 (several weeks)
exté
EDIT : 12 oct: once again i have this message at each boot "Press SEND to restore factory default ..." UNABLE to bypass ... please help , i find no solution on google and i refuse to think i am the only to have this issue ...
Hi,
I have ~ the same problem.
After an upgrade, my trinity did not reboot.
I tested : soft reset, hard reset...
My device did not boot
After reading your post, I removed the battery during + 20 minutes then tried to reboot. Result : no change
Do you have any idea to resolve my problem ?
Thanks,
Kabylus
kabylus said:
Hi,
I have ~ the same problem.
After an upgrade, my trinity did not reboot.
I tested : soft reset, hard reset...
My device did not boot
After reading your post, I removed the battery during + 20 minutes then tried to reboot. Result : no change
Do you have any idea to resolve my problem ?
Thanks,
Kabylus
Click to expand...
Click to collapse
I saw this solution bellow from this forum
23rd June 2009, 10:07 AM
albgen
Junior Member Join Date: Aug 2007
Posts: 13
--------------------------------------------------------------------------------
if your htc hangs like mine(blakc screen and nothing else) you have to load the boot loader.
To load the boot laoder press power+camera+softreset. You will see on the screen some colors. Then plug your usb cable and refalsh.
ps:soft reset is the button over the call button
Posted by albgen (Junior Member)
Hope this helps
I had the same problem when I did the upgrade to wm6.5.
however, dispite the facts that your phone already dead, no harm trying the same method again.
1) remove the battery.
2) press any buttons, the best one to choose, on off button. (Reason, all phone has backup battery, you got to drain it completely before the memory is fully wipe off)
3) Best is, leave the phone without batt for a day or weeks and let the backup batt drain up.
4) pull the batt back, press the right & left soft button & the reset button (HARD RESET).
It works for me...
Good Luck to you guys!
mischunt said:
I had the same problem when I did the upgrade to wm6.5.
however, dispite the facts that your phone already dead, no harm trying the
Click to expand...
Click to collapse
Hi Mischunt,
which kind of issue you have ?
trinity which refuse to boot or same screen as me "press send to restore ...." because this issue came from to time (when the battery is empty i believe) and now impossible to my device to boot again
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
Hi guys.First of all I am new to htc and i am kinda noobie.
I ve been searching the threads here but I cant get my p3600 to boot.
The problem is that when my phone starts I get a 3 or 4 coloured screen and then
the message: "Press SEND to restore to factory deafault,press END to quit"
When I press SEND it says: "Restore...Completed Press OK to boot"
When I press OK I get the first message again, and again...
Any ideas if it is fixable..?
Maybe reinstall rom/kitchen ? What do you have on atm ?
I don't know what you are talking about
I tried splxploit with ubuntu but my computer can't find my phone!
Can i use activesync without turning on my phone,because i cant!
I tried using format rom without result
Hi Guys, I come to the point where I need help please, I have very long experience in rooting but this issue I could't fix and/or find a solution for it since the 901S is unrooted there is no EXE RUU not been touched. This is my wife phone and I had same issue with main a year ago but since my phone was rooted I could fix it.
The issue is when the phone start rebooting by it self at once, nothing was done to cause that like installation app or what so ever. It start and when reach home screen, few sec it reboot from 0.
phone data: S-On, Hboot-1.61.0000, Radio 4t.31.3218.26, oS-5.16.709.4
I have tried this:
-Unlocking with unlock_code.bin, is give me the yes/no screen when I click yes it reboot to stock recovery then nothing, (it show the message about missing E bitmap)
-uploading rom stock or any other didn't work, not by using fastboot or any other method I know.
-run into save mode help give few more secs but nothing, it reboot here too
-factory reset from device didn't work as I click okay but it keep resetting.
-order *#*#3424#*#* and factory reset also nothing.
-the device memory is 95% full, I tried to format data or system or from fastboot or by deleting files also nothing get deleted all stock and after restart I see ever thing like it was.
any suggestion here?
thx all,
Any help any one
No one no help!!