Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
dam1en said:
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
Click to expand...
Click to collapse
Sounds like a hardware issue or simply a bad flash. Have you attempted to reflash the rom? Which rom are you using?
Well...
It wasn't working again this morning, but suddenly - out of nowhere - began to work properly. I'm stumped. If I ever figure out the exact issue I'll be sure to post back.
Thanks
Greetings,
I have same problem on my tytn...
Sometimes it suddenly starts working fine, but shortly it breaks again.
I have tried hard-reseting while it was working, but didnt help.
I think the problem appeared after charging my phone with a motorola v3 charger, so maybe it damaged my phone with over-voltage or something...
Anyway, if someone can suggest something i would be very grateful!
Hi I have exactly the same symptoms with my HTC Tytn II...when you power it on it starts typing letters (in my case CEDF). If the recording button is active it will start recording too. This happened suddenly and I haven't used any other charging apart from the usb and wall socket charger supplied with it.
All buttons (except front center key) and keyboard do not work. Any suggestions would be appreciated very much. This phone is only 8 months old.
Hi,
my Kaiser with dutty's WM6.1WWE ROM did the same this morning Yes I disabled the button 6 and stopped the voice recordings but all the hardware keys but few in the center of the keyboard are not responding. So I cant make or receive calls without taking the stylus out and touching the screen soft buttons andd that's pin in the ... while I am driving. I am using this ROM for almost a year now and I am extremely hapy (up to now) with its performance. When it all happened there were no activities on the phone - I woke up from a SMS notification (Yes I did receive an SMS from my bank) followed by repeting Voice Recordings. Any help will be highly appresiated! Thanks in advance!
keyboard problem
I am experiencing a similar problem with my stock tilt my keyboard does work however none of the text appears on the screen. I have tried hard reset and everything else I could think of, short of a clear storage reload. I would appreciate any help or suggestions from some of you more experienced users.
Bisonwill
anyone ever figure this problem out? im having the same thing happen now.
Same here
I've had it for a couple of weeks now.
I'm running WM6.1 from HTC (rom ver.3.29.422.1 from 2009-01-12) so nothing fancy here.
I even ordered and replaced the D-Pad and I replaced the keyboard (just the sticky part though). I totaly dismantled the phone and didn't find any issues with the cables.
Any ideas would be highly appreciated
Join the club!
This is crazy. My problem is exactly the same. I re-romed to the latest phoenix and it did not change a thing.
Help!
help....
any body here found a solution for the keypad/keyboard yet??? i have the same problem as you guys... any idea, thanks so much...
i have the same problem And there is something else. My Kaiser wakes up every 2 minutes - it's killing the battery. It works only for 6 hours now
Help
bump!!!
No more people with this issue or any solutions?
Pls! Help
ive joined the gang!
I decided to flash my cooked rom ive been working on.
i hadnt changed much in the kitchen and i think the flash has went badly.
it starts booting windows and where it should state "calibrate screen" it goes white and hangs there, buttons seem to respond by lighting up when pressed.
Now when i try to get it into bootloader or even hard reset it just doesnt work.
it just restarts the phone.
before this happened the backspace key hasnt been working for ages.
anybody got any ideas??
(lucky for me i have a backup kaiser!)
I'm having the same problem. Automatic wakeup, applications starting automatically, can't use keyboard, have to to use screen to use phone etc. I've hardreset using the clear storage method, reflashed a couple of times, but nothing helped. So here I am joining the club
If it's not a hardware issue, then try to flash another radio, many of the custom ROMs here doesn't include a radio, so if it's caused by a wrong radio, flash a new ROM without a radio doesn't help.
Check the Sticky for 'how to' if not aware.
PS: Check here for something need to know..
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Danhargreaves said:
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Click to expand...
Click to collapse
Try this:
1. Take out the battery from the phone.
2. Take out SIM card and SD card.
3. Press in and hold the CAMERA button.
4. Plugin to your computer using the USB cable, while keep holding press in the CAMERA button.
See does it enter the BOOTLOADER mode.
Once entered the BOOTLOADER mode, you can flash a new radio or rom right from there, in your regular way of running KaiserCustomRUU.exe.(Since you already have a HardSPL flashed on, otherwise a HardSPL is needed to flash first.)
Good luck.
Edit: If the power button and the camera button is still working, you can use the regular way of entering BOOTLOADER mode, and flash from bootloader mode or flash from SD card.
Originally posted by Manpreet @ www.sakajati.com
To enter in bootloader mode:
Simply Switch off your phone. Press and hold camera button and also press and hold the power button..You can remove ur finger from power button when phone is switched on but keep holding camera button until u come to bootloader …Now attach the usb to ur computer and do the flashing you normally do.
Click to expand...
Click to collapse
Thx for your suggestion:
I tried removing battery as sim and sd were already removed due to previous attempts in fixing!
so:
i removed battery (did not put back in), plugged in while holding camera
got nothing, so held power button at same time, the green light came on, then went off, and came back on again. but no bootloader.
i tried same procedure with battery in, and all i get is the OS loading up, no bootloader no matter how long i hold the buttons.
is there any other alternative method to get into bootloader (possibly involving other button presses)?
or any other ideas.
Really want to fix this as it was my "experimental" phone for cooking roms with.
Thanks again.
Suspect you have some hardware issue with the camera button. Can you ever take a photo with it?
Edit: Did you read through every post onthis thread:
MTTY (How to fix a bad ROM flash!)
If you tried that and still no luck, you can post your questions there. There are masters will keep an eye on that thread. And generally they only have time to look into their 'subscribed' threads, chances are they will not look into here.
Edit: Maybe the procedure I told is wrong, since I call from memory, check this:
dwny said:
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
Click to expand...
Click to collapse
Edit again:
And try like:
Plug in USB first, and thenn press & hold Camera, Power button etc.
I remember once I read there is a way to enter bootloader without battery, just can not find the original again.
fixed it, please close
ShavedCivic187 said:
So I was texting on my Fuze and it froze. I hard reset it and now it won't start back up. Im using the latest Mercury Energy rom. It starts up, goes to where it plays the start-up sound and says "Energy Rom 3.0" and then stops. I have the touch response installed on it and it still vibrates when u touch it, so I dont think its too bad. Please Help! Thanx
Click to expand...
Click to collapse
Hold the Volume button down + the button in the middle + the reset button
keep holding until the screen goes to bootloader
CraZyLiLbOy said:
Hold the Volume button down + the button in the middle + the reset button
keep holding until the screen goes to bootloader
Click to expand...
Click to collapse
then reflash?
tryed holding the buttons and it didnt do anything.
He's advising that you hard reset. That's what I'd do, too, but if it continues to hang, flash a stock rom. You may need to go into bootloader manually if you do it over usb.
Fixed it please delete.
hard rest verizon phones
i think that verizon has ****ed the customers when i comes to hard resetting i think that they disable the option when you are try to do it with the whole volume button power button the reset thing i have gone through two phones because of this but now i found program that was leaked and it does it for me you go into that mode where you get that multiple colored screen and then once you plug you phone into your computer and then you run it and it hard resets the phone
that would be great if you can share how do you it with us, so any body have this problem can be fixed without asking too much.
Hi i have a few issues on my diamond. I hope you guys could help..
1st issue: lately my diamond keeps on resetting by itself.
2nd issue: later I've learned that when I record my voice using the software within the ROM, I don't hear anything but when I record my voice using my htc headset/earphones there is a sound.
What I did was:
This day I've flashed a new rom (Energy Rom) into my Diamond. It works ok then I flashed the Radio (Radio_1.13.25.24). I was able to use my diamond for a few hours.
Now..
3rd issue: My diamond is not powering on..
What i did before this happened was...
I pressed and hold the power button for about a few seconds so the ShutXP would pop up and I could soft reset my diamond.Before I clicked the soft reset button, I was checking out all the functions of it. then i clicked, a little icon,which is the Setup Timer Action. Here's the setup:
Action: Turn Off Pocket PC
In: (i don't exactly have seen the time indicated)
As curious as i am, I Clicked the Set Action button. It did shut my diamond off. Then I tried turning it on, but all it was doing was vibrate and the screen was black. At first I was hearing the start up sound a few times but later it didn't hear it anymore. I plugged in the charger but there's no white light on the circle button which used to have a light on the borders of the circle button when plugged in the usb cable. I tried pressing the power button plus the Volume down so the bootloader would appear but it did not. What shall I do?
Are you sure that the screen working because the phone vibrate and play the startup sound so if think its the screen that have som serious problem !!
HELP
I also flashed a new rom (Energy Rom) into my Diamond before.
It cannot run window mobile6.5.........how can I do???
I cannot connect to PC .......
I recently also had a similiar problem, after attempting a flash of the Rom, the ROM update stopped halfway through and reported that it had lost connection to the device....
The whole phone would not vibrate/power on, nothing - no glowing ring around the middle button to indicate it charging at all.
I had to return to the repair centre and somehow they didn't notice that I had modified the firmware and replaced the whole phone for free citing a hardware issue ...
Doesnt sound good if you cannot hard reset the device
Hey Guys,
I have a little problem with my Diamond (actually in MDA Compact IV costume lol xD)
Since I flashed the AZTOR RE Evolution Rom my Volume Control has gone mad! Right after WM booted it is starting to push the Volume all up. It doesn't even react when I am touching the screen or try to set the device to vibration / silent in the Settings Tab.... I tried to flash another rom but this issue followed me to the new rom, too!
Now it even got worse and the Volume Control is appearing every time I touch the screen.
It seems that the Vol UP button got stuck... but somehow I do not believe in my diagnostics xDD
Does someone have an idea what i could do to get it working again?
Thanks in advance
I had the same problem
1. hold the opposite vol button to the stuck one for 30 secs or so
if that doesn't work flash a new radio then a new rom
hope it works for you
Hi hope someone can help. Over the weekend my TD2 started playing up. All of the hardware buttons apart from the on/off button have stopped working. I also notice that if I turn the screen off with a short tap of the on/off button, after a few seconds it comes back on again. All touch screen functions are ok. It also appears to be draining the battery very quickly, to the extent that fully charged at bedtime (no bluetooth or wifi on and a stable 3-4 bar signal) it will be comppletely drained by morning. As far as I am aware the phone has not gotten wet at all.
I have also re-installed the office HTC rom, which made no difference
Any ideas??
So you reinstalled the stock rom and did a hard reset?
You can try Tarkim's Keyboard controller and see if your hardware keys can be mapped to a different function.
That would help eliminate hardware vs software issues.
I have the same problem. Also my backlight keeps working and won't go off. Can't perform a hard reset because my volume buttons(and all other hardbuttons accept the on/off) aren't working.
Searched for the solution but can't find it anywhere. Who can help me?
daanbrok said:
I have the same problem. Also my backlight keeps working and won't go off. Can't perform a hard reset because my volume buttons(and all other hardbuttons accept the on/off) aren't working.
Searched for the solution but can't find it anywhere. Who can help me?
Click to expand...
Click to collapse
Try clear storage app to HR.
Thanks for your reaction.
Yesterday I managed to put an official ROM on my phone.(latest from HTC site).
Problem only got worser. Phone gets complety stuck(directly after boot) in the volume screen. Sometimes its flashes back to the normal screen but only for 1 second. Buttons still aren't working so can't do anything with my phone right now( not even the hard reset methode you told me).
Started to think that this is really some hardware issue. Can't remember that water got in my phone or the phone felt really hard. Any solutions maybe?
Otherwise I think I just go to the store.
daanbrok said:
Thanks for your reaction.
Yesterday I managed to put an official ROM on my phone.(latest from HTC site).
Problem only got worser. Phone gets complety stuck(directly after boot) in the volume screen. Sometimes its flashes back to the normal screen but only for 1 second. Buttons still aren't working so can't do anything with my phone right now( not even the hard reset methode you told me).
Started to think that this is really some hardware issue. Can't remember that water got in my phone or the phone felt really hard. Any solutions maybe?
Otherwise I think I just go to the store.
Click to expand...
Click to collapse
One last thing you can try is a Task29 explained here.
Use your official rom (right click on .exe and extract the RUU_Signed.nbh and place in task29 folder, then connect device in Bootloader mode and run the Task29.exe. Follow the instructions in the link.