Related
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!
this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm
Thanks buddy!
I'm happy that worked for ya!
Take care!
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse
It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?
Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse
Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse
I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)
Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.
Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.
Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.
Worked great. Back to T-mo she goes!!!
BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.
Hello,
I`m trying to get latest lvsw wm6 to the device.
I own the phone since today.
I made the following steps:
Execute ROMUpdateUltility (Hard-SPL)
->Next->Next->Update
From: Image Version 1.16.407.2
to: Image Version 1.20
->Next -> Next
On the phone:
Enterbotloader.exe
"blabla"
YES
On the computer:
ERROR[246]: Device not responding
On the phone:
IPL-SSPL by Des
SPL-1.07.ds
ok,
trying to run ROMUPdateUltility again...
next next next... he shows me the progress bar --> finished! YES!
Rebooting the phone --> same software version as before the update?
trying to update for 2 hours... just to use gps as advertised
please help, i tried the official Update from HTC -> successfull but effects! programs, contacts etc still there, same version number!
messiah said:
please help, i tried the official Update from HTC -> successfull but effects! programs, contacts etc still there, same version number!
Click to expand...
Click to collapse
I've the same problem [246] upgrading unofficial roms like
GSM_1.41.00.11
and
ROM_ING_WM6_2.27
The only upgrade I make successfully is original
htcp3600-RUU_Trinity_HTC_ITA_1-23-408-2_103_6275_1-38-00-11_108
what's wrong ?
P.S.
I test it using activeSync 4.2 & 4.5
Messiah..... Have you read the very first post in the LVSW ROM thread?
I am NOT having ago, just checking, seems you may have miss-understood.
Grab ALL 3 downloads listed there.
Apply first one, and yes there IS NO real visible change to the phone apart from it has been hard SPL'd
Now apply Second one, will go through the same process BUT the Radio ROM is changed and updated
Now Apply the Third and WM6 is installed
The failure you describe is the computer dropping Activ Sync and then "seeing" the phone in Bootloader mode, which is why it take 2 bites of the first cherry, after that all "should " be ok.
I managed to get mine on the first attempt so it is "Me Proof"[TM] and "Just Works" (c)..... however report back if this hasnt helped
yeah, the process you described tells me that you've loaded hard-spl on your phone.. that's all. No WM6 yet...
I have the same problem.
I have Hard-SPL'ed my Orange M700
Then reboot and reestablish Active Sync
Then I have updated the Radio Rom
Then reboot and reestablish Active Sync
and now it's 1.41.00.11 in settings/system/device information
but when i apply
20070527_Trinity_WM6_v2.0.1.1 it uploads then i power on my device and it's still WM5 ?
What am I doing wrong??
Any help appreciated.
This may be a stupid question but have you SuperCID your device before running the updates?
If you go:
Start -> Settings
System
Device Information
What does it say under Radio version? (Just checks the second step has been completed successfully).
Also when you enter the bootloader what does it say on the screen?
akirainblack said:
This may be a stupid question but have you SuperCID your device before running the updates?
If you go:
Start -> Settings
System
Device Information
What does it say under Radio version? (Just checks the second step has been completed successfully).
Also when you enter the bootloader what does it say on the screen?
Click to expand...
Click to collapse
I thought you didn't need to SuperCID the device (http://forum.xda-developers.com/showpost.php?p=1245390&postcount=70)
My radio Rom shows 1.41.00.11
TBH I don't know. But it can't hurt to try it, I SuperCID mine and it flashes perfectly each and every time.
I'm merely trying to make suggestions that may get a result.
Oh, you didn't tell me what the bootscreen said and what version of Activesync do you have on your PC?
While doing the SuperCID upgrade i was wondering: After flashing any of the ROMs do I reboot or power On manually or wait for the device to reboot itself as the message in the SupoerCID tool suggests:
If radio upgrade went fine, wait until your phone reboots and make sure
ActiveSync is enabled again (you should see green icon in system tray)
Click to expand...
Click to collapse
Stupid Q: How can i make the boot screen stay long enough so i can write it down?
My ActiveSync is 4.5 on WinXP
Rummage around in Start--> Setting --> device ID, and version and stuff...... they are there and you get the same info as on the boot screen... and it stay on longer ;-)
Sorry if a little vague but away from phone at the moment......... erkkkkkkkk
/me runs off to find it so this may get edited
akirainblack said:
TBH I don't know. But it can't hurt to try it, I SuperCID mine and it flashes perfectly each and every time.
I'm merely trying to make suggestions that may get a result.
Oh, you didn't tell me what the bootscreen said and what version of Activesync do you have on your PC?
Click to expand...
Click to collapse
I didnt Super CID just followed the instructions in LVSW 's first thread, applied each DL in order and "it just works" (c)
Thanks. That's where i got the infroramtion from b4. I just thought it might be different in the boot screen.
I now did the SuperCID unlocking and did the 3 upgrades again. after the 3rd upgrade i still have:
- WM5.1.342 Build 15096.3.0.0
- ROM 1.23.61.5
- Radio 1.41.00.11
Q again: Do I need to wait after the flashing or do i immidiately press power
(that's what i do when it says finish) or do i soft reset? Or what else?
Thanks for your help.
Hmmmmm just got me phone....... dont ask
Right CE OS 5.2.1413 build 17745.0.2.3
ROM 2.0.1.1
Radio 1.41.00.11
Sooooo.......
a) are you using LVSW (just to be sure)
b) have you grabbed the latest version posted on page 1 of the upgrading thread?
c) I let it restart it self after it finished flashing, it then reclibrates the screen etc etc
Also looks like you havent upgraded anything just yet ... follow the instructions to the letter and it "should" be fine
a) yes
b) yes
c) there might be the problem i waited 2 mins ans as it wasn't rebooting i just used the power button. How long should i wait aftr the WM6 install?
I soft reset mine directly after the screen goes black. So that should be fine.
Maybe it has to do with my boot loader:
When i go to bootloader i see:
IPL-0.50
SPL-1.07.0000
then it starts fading quickly. is this normal? I have the same fading effect when i install ste 2 the radio ROM. but i still have the new radio rom on as it displays as 1.41.00.11
I again tried to use the 2.0.1.1 it uploads very quickly (maybe 2min) and then it's still the "orange" screen and WM5 on reboot and i still have all my data.
What a I doing wrong?
No. Mine stays there right up until the upload to the phone starts.
Then I get a grey background with a blue progress bar.
What happens if you run Enterbootloader on the phone. Then connect it to the PC.
Then run the install program on the PC.
The first process didn't work.
You should have:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
Hmmmmm if all else fails try a hard reset on your phone and see what versions of what you have after that.
Did you use ANY form of unlocking prior to using LVSW rom?
/me suspects this might be casuing issues
The radio rom zoooooomed up to my phone and likewise the WM6
I cannt remember reseting the phone after flashing.... IIRC it just worked as in it finished then re-started and way hey off it went.
Also FWIW I just used the DL's in the thread without bothering with anyother boot loaders etc... ie extract flies in first DL into 1 folders, run them, ditto DL's 2 and 3.
Hi guys,
Please forgive me for asking the question, I've spent the last two hours searching for someone with a similar issue and can't find anything.
Basically I'm wanting to sim unlock my UK Orange TyTn II (Kaiser). I've read through the unlock thread and know that I need to install HardSPL. I've installed v1 - it all goes through fine but I don't seem to be able to get into bootloader mode.
I've flashed the radio image as per step 5 (step 1 folder) and this went through okay and changed the radio image. I reflashed it to 1.27.12.17 and during the flash process where it takes the phone into bootloader mode as part of the ROM update utility I could see it said SPL-1.0.OliPoF on the 2nd line of the bootloader (which means HardSPL is installed doesn't it?)
No matter what combination of buttons I've tried - holding the camera button firmly, holding the camera and power button and reset I just can't get the thing to go into bootloader mode using either a soft reset or from a clean power on. I've tried it with and without sim card and sd card to no avail.
My original rom versions were:
r 1.27.12.29
g 22.45.88.07h
d 1.81.00.00
Obviously the radio version is now different but the other two remain the same.
I'm confident that HardSPL is installed, I just can't get to the bootloader!
Any help would be much appreciated.
Oh dear.
I've just put my orange sim card back in and I'm still getting the network locked please input unlock code that I got with the "strange" sim card even when I've overwritten the radio rom with a newer version.
Balls
--update--
Tried another radio version and still it says network locked with original orange sim card, so I've got no choice but to try to get the bootloader thing sorted as I can't use my original sim now. Ever wish you'd not started something?
--update--
Paid £20 to IMEI-Check.
--final update--
Updated to Dutty's latest ROM, everything is fine, still unable to make the phone go into bootloader mode so no idea whats going on there. HardSPL is definately installed. This new ROM is so much nicer than the orange factory setup.
Serves me right for being stupid
the same here but with hermes.. from SPL 1.09 tried to install hardSPL v7, done it NOT in bootloader mode, processed to 'finished' page, WM is working, but can't get to bootloader anyhow.. installed drifferent ROM, succeeded, but can't get to bootloader either.. any ideas what is going on??
So i just attempted to flash my tilt.
These are the steps i did.
Used Jump SPL 1.56 Kais
Then flashed a Kaiser Custom RUU.exe
everything was good at this point.
I then attempted the Kaiser SUperCID tool
when i did the unlock radio is when the problem occurred. After initializing and completing the screen turned black and does not display anything after the 3g sreen. I have done several soft resets and am attempting to do a hard reset with the soft keys but all it does is restart the phone....
i am not able to do a hard reset via sys>clear storage since no screen is displayed
this is what my phone does show
the tri color screen is this
kais1*0
spl-3.28.Hard
cpld-8
and it says security unlocked above all of that.
The ATnT screen shows this
R 1.70.Olinex
G 25.65.30.04h
D 1.62.00.00
please help
You need to follow step 0. Too late know. Which includes having an actual "RADIO" ready.
1.70OliNex is not a Radio. Thusly the Device can't load the Phone. Find a Radio and Flash it
Oh And Count this as your Freebie. Next time Search for your answer. And if you don't find the answer this should have been posted in the SuperCID thread.
Thank you kind sir. Off to look for a radio
Ghxoxst said:
Thank you kind sir. Off to look for a radio
Click to expand...
Click to collapse
Before you go off.
Here's something to try. The SIM/CID Unlocker do not work with the stock rom and you should have put hardspl on there.
Setup activesync and make sure that it detects your phone. As long as activesync works, you should be able to flash the stock rom and radio on the phone (even if the display is blank).
1st use jumpspl
then put on hardspl (read and follow the hardspl instructions)
then upgrade to 6.1 ROM
Then Unlock
then reflash with the rom of your choice with the matching radio
you should be good to go.
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Ghxoxst said:
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Click to expand...
Click to collapse
If you have hardspl on there, then just flash one of the cooked roms on the phone. I loaded the L26 Rom and it works great. It will include a radio firmware and is compatible with the SIM/CID unlocker.
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Ghxoxst said:
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Click to expand...
Click to collapse
Have you connected it to the computer via usb? Does activesync see the phone? You won't see anything on the phone itself until you correct the problem. As long as the computer activesync sees the phone you should be able to flash it from the computer.
I had the same issue
Just follow the steps
get the SIM unlock code from the computer
then flash a "real radio"
Once it finishes and boots up
it will ask you for the sim unlock code
AND VIOLA!!!
got it going
flashed it from my mini sd card after fat32 formatting it.
works like a charm
Thanks to everyone
I am super new to this. I have 2 att tilts I followed a guide on this site and flashed them both to windows 6.5. both seemed to be working fine. My wifes had no sound though. So I searched and realized hers had an older radio than mine. I followed another guide here to update her radio. (I picked the same one as mine 1.65.21.18) I tried the sim card first and nothing happened so I tried it via sync. It got to 99% and errored. I followed the on screen commands and the second time I got 0% and errored. Now the phone is stuck in the multi color boot screen and nothing I do fixes it. I have tried searching and cant fix it. I dont know what mtty is. Please help!!!
fragnbastich said:
I am super new to this. I have 2 att tilts I followed a guide on this site and flashed them both to windows 6.5. both seemed to be working fine. My wifes had no sound though. So I searched and realized hers had an older radio than mine. I followed another guide here to update her radio. (I picked the same one as mine 1.65.21.18) I tried the sim card first and nothing happened so I tried it via sync. It got to 99% and errored. I followed the on screen commands and the second time I got 0% and errored. Now the phone is stuck in the multi color boot screen and nothing I do fixes it. I have tried searching and cant fix it. I dont know what mtty is. Please help!!!
Click to expand...
Click to collapse
to fixing bricked kaisers with MTTY commands looks at http://forum.xda-developers.com/showthread.php?t=371154&page=5
Thanks. I'll check this out.
Once again it says run mtty. What is mtty? is it a program? if so can I get a link? i googled mtty and there is a download but im afraid it might be a virus so if anybody here has a safe link id appreciate it...
fragnbastich said:
Once again it says run mtty. What is mtty? is it a program? if so can I get a link? i googled mtty and there is a download but im afraid it might be a virus so if anybody here has a safe link id appreciate it...
Click to expand...
Click to collapse
MTTY is a program command ....here use it
Thanks for the program, when I open it and go to usb and type command boot i get
Cmd>boot
Command error !!!
I also have ruunbh in top corner I followed the link on the tutorial to download an original kaiser rom but there were none....
ok I typed
set 16 0
then
task 8
My phone rebooted to windows 6.5 but still has wrong radio. I am afraid to try and change radio. is there a link to a step by step procedure that works. did i pick the wrong radio?
TPC_Kaiser_Titanium_Ultimate_28002 is rom
Kaiser_Radio_only_1.65.21.18 is the radio that i tried to do last time...
r-1.27.14.09 is radio it has now...
http://blog.contriving.net/2009/06/18/upgrading-your-att-tilt-to-windows-mobile-6-5-tutorial/
is the tutorial i followed to flash rom. I am not sure if i installed Hard SPL i followed that tutorial. I did jumpspl 1.56...
fragnbastich said:
ok I typed
set 16 0
then
task 8
My phone rebooted to windows 6.5 but still has wrong radio. I am afraid to try and change radio. is there a link to a step by step procedure that works. did i pick the wrong radio?
TPC_Kaiser_Titanium_Ultimate_28002 is rom
Kaiser_Radio_only_1.65.21.18 is the radio that i tried to do last time...
r-1.27.14.09 is radio it has now...
http://blog.contriving.net/2009/06/18/upgrading-your-att-tilt-to-windows-mobile-6-5-tutorial/
is the tutorial i followed to flash rom. I am not sure if i installed Hard SPL i followed that tutorial. I did jumpspl 1.56...
Click to expand...
Click to collapse
If you are not sure how to use MTTY, please don't use it. This is a powerful tool and if its not used correctly you can definitely bricked your device. Try to read first of what you do.
I have spent hours reading and searching posts the last couple of days. If you have a helpful answer for me feel free to post it! I followed the tuorials exactly. Not to mention I already DID USE MTTY and it worked! Now I need to change the radio... All I need to know is if I need to run hard spl first or jump spl? The tutorial I followed just had me run jump....
PS. I don't need to become an expert I am only updating to sell these phones on ebay. You get more for them with windows 6.5. Once I get them working I am selling them and will never use these tools again. I switched from ATT to Virginusa and an android phone...