Kaiser/TyTn II and QPST? - Tilt, TyTN II, MDA Vario III General

Hello, I'd like to request information on how to use QPST with my Kaiser via USB. QPST shows 'No Phone' on all ports and I don't seem to be able to enter diagnostic mode.
Any advice would be greatly appreciated. Thanks.

i'm running Vista if that makes a difference...

I also have a PC running XP if that helps.
Nobody will help me?

i am trying to do the same thing, i have gone as far as flashing to jockyw's spl with tty enabled. but i dont know how to put it in qpst diag mode... i am using vista, but also tried under xp, with no change.

I'm trying to do the same thing. I can get the comm ports to show up and use QPST while the phone is in the tri-color bootloader state. QXDM will also works in that state but since the phone is not runing, I get no useful information.
I have not been able to get the com ports to show up with the phone is fully booted like I can with CDMA smart phones by dialing ##DIAG#.

you can get qpst to recognize it in tri color mode? the only way i was able was to put it in download mode by issuing rtask a, and radata 90000000 1. after that i installed the motoq drivers available in the frankenkaiser pack. it shows up in qpst as download mode, but it can not mess with anything because it is in dl mode. if you know how to put it in diag mode, that would be a step for me!

I have installed the wmodem drivers and put the phone in bootloader. But qpst sees nothing. Is there a diagnostic mode similar to a CDMA phone.

does anybody know more about qpst?

Related

Diamond with non-bundled AS?

Hey All.
I am on vacation, and just brougth a new notebook (lovely Medion Akoya), and i want to sync with my diamond. However, i downloaded the active sync from the ms homepage, and i get the "Unrecognized device" error all the time.
Yes, i tried to use different cables, yes i tried to deactivate the advanced network, however, i doesnt seem to recognize it at all.
Even if i do a softreset + volume down, i just get the SPL1-40 screen, but eventhou my phone is plugged in the USB, it doesnt say that, only "serial" when i disconnect.
I've been searching this forum the entire day, and i cant seem to find a solution. So, i kindly ask the gurus help me
Diamond running 0.95 bePe and pc running xp sp3.
Kind regards, Heien.
Try to flash a stock ROM and check if you run into the same problem.
In order to sync, you must be running the handset normally, don't enter bootloader mode.
Did the system prompt you for drivers the first time you connected it to the PC? Activesync 4.5 provides the rndis drivers.
the problem is, i cant even flash my device, i tried to flash it, but i get a connection error with the tool.
I know about the bootloadermode, and that i am not able to sync in that state, but i just wanted my pc/diamond to recognize the connection between them. The system did not prompt me for drivers, it just went straigth to unrecognized device. i even tried to point the the driverupdate tool to the drivers folder with the rndis drivers in the as folder.
-i also tried to hardreset my device.
Try doing the same on a fresh stock XP install, without firewall or anything similar.
We need to figure out if it's a problem with the handset itself or your OS/PC.
Try another USB port (DON'T use hubs).
Enter bootloader mode. When you connect it to the USB, it should at least toggle from serial to usb.
If that's the case, at least your USb is working well.

What to do when computer doesn't recognize phone plugged?

I have a problem with the diamond and needs to change ROM/SPL and other stuff, but it won't recognize that the phone has been plugged in. I have tried 5 different USB cables and 3 different computers. I don't have HTC warranty. I've done 5+ hard-resets.
Please help.
First, what OSes? For instance: win 7 doesn't recognize the phone if it tries to connect in active sync mode.
I've always used windows xp, in the past it worked.
hi,
try to connect your htc twice : my computer does not recognize my htc at first plug but when I retry in less than 1 minute, my htc displays popup menu and I can choose USB/active sync, I click done and then my computer recognizes it. I don't know if it will work with your device but you can try that ^^
Thanks for the suggestion,
I've already tried that a lot of times, nothing doing.
ok, did you try to change the status of your usb connexion ?
I mean : settings>connections>usbtoPC> then try these 4 combinations together :
- enable faster data synchronization (try both modes on/off)
- ask me about usb connection type (try both modes on/off)
I can get into bootloader, but never know that you could flash ROM in there. Is there a guide?
Also, I have a problem with a flickering screen that some threads here suggest changing SPL version to fix. Is it possible to change SPL using bootloader?
I just downoaded WM6.5 to my phone and did a ROM flash from internal storage, but USB still has problem & flickering screen still there. I need to be able to change the HardSPL w/o connection to the computer.
Is it possible to load some of the .exe in the HardSPL package and run it on the phone?
Someone help,
Thanks
Perhaps it's simply due to your PC firewall ?? Deactivate it and try to plug your htc again...
the problem is that my the computer doesn't connect with the phone via the USB cable.
just try to disable your PC firewall before connecting your device.
sorry I cannot find CustomRUU.exe on this forum, i did find DiamondCustomRUU.exe on the wiki. However, the interface for it is the same as the RomUpdateUtility.exe, which requires activesync connection.
I did proceed anyways by entering bootloader(Voldown + softreset) and run the utility -> nothing works. Then I try the USB trigger mode (Voldown + back + softreset) and run the utility -> nothing works.
I am tempted to put the HardSPL in the internal storage and rename it DIAMING.NBH and flash it but I do not know the consequences.
Thank you for your replies,
I'd appreciate more help

Big Problem - Is my Kaiser dead??

Happy new year everyone!
I have a big problem with my kaiser, maybe is 2011 a bad year for me ..
Well, I flashed for the third time the modded kernel of DnbTommy (including a RADIO, SPL, etc..).
Just after the flash, my Kaiser won't boot!
Just a black screen, and green LED. (can't hard reset, flash, or anything ..)
I made searchs on XDA and more, and I heard about MTTY solution..
But when I plug in my Kaiser in the USB cradle, it recognizes an unknown "Data Interface".
And MTTY does not recognize the USB port.. I tried on a Windows 7 (x64) computer, and a Windows XP (x32) laptop, with the same results.
Thanks for your help!
Try removing the battery for roughly 30 seconds then re-install
I already did it, even changing battery, but no results
Go in flash mode (camera button and reset) and flash another nbh.
Hi L1q1d,
Unfortunately, I can't go in flash mode, bootloader mode, or anything..
My screen stays black, and I can't flash!
Is the battery charged?
Of course it is !
I really need help please, elsewhere, my Kaiser will be lost..
Thanks in advance!
Have a search for the Diagnostic drivers you might be able to connect with mtty with them?
If you mean the drivers folder named
"x64 AS Drivers Win 7 Tested & Working" ,
including 2 files : wceusbsh.sys and wceusbshx64.inf
then, it does not..
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
meknb said:
No i mean the motoQ diag drivers these work with win 7 not sure about x64 ?
Click to expand...
Click to collapse
Okay I will try it, then! Thanks!
Do I have to install them when it asks for "Data Interface" driver?
Yes just unzip them first.
Well, I tried on a Windows XP 32 Bits laptop.
I plugged in my Kaiser with USB cable, installed MotoQ Drivers when it asked for "Data Interface" drivers,
But when I run mtty.exe, it shows me 3 more "COM" ports.. But no USB!
If I plug out my Kaiser, 3 ports less appears, then..
What could I do now?
Thanks!
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Try setboot 0 then cego via mtty.
meknb said:
I haven't a kaiser but id suggest looking through the frankenkaiser threads, you can connect mtty via a com port check device manager to see what port to connect with.In device manager look through the serial ports.
Click to expand...
Click to collapse
When I connect the Kaiser, 3 ports appears in device manager / in MTTY :
- COM3 (cant find its name in device manager)
- COM4 : "Qualcomm Diagnostics Interface 6000"
- COM5 : "Qualcomm NMEA Device"
If I connect to COM3 or COM5, MTTY seems to be blocked..
But if I select COM4, MTTY doesn't crash, but i'm unable to type a command, because it says "Invalid command" to everything I write..
Really, thanks for ur help!!
Yes com4 is the one you need to connect mtty with but id read through the frankenkaiser and related threads,you may find more help there. Good luck
I found here the thread named "Frankenkaiser SPL Loader" :
http://forum.xda-developers.com/showthread.php?t=394584
I tried the step 4, but nothing happends.
I cannot connect to MTTY with the Kaiser, that's the real problem..
Maybe there's another way than MTTY?
Over two years of flashing, it's the first problem that I get with the Kaiser..
Thanks! I really hope to find a solution to make my kaiser alive..
One thing to check is disable Allow usb connections in windows mobile device centre.
Another thing is try different versions of mtty i use mtty_0513_Test or you can try putty does the same thing as mtty.
I'm sure you'll get your kaiser back to life again.
I had stopped rapimgr.exe, but after you told me, I unchecked the "usb connection" box in ActiveSync..
Tried with MTTY 1.42, 0.01, 0513_Test, but nothing happends..
Same with PuTTY...
I think it's a communication problem!?
I would donate you, if you find the solution..

droid won't go into diagnostic mode

ok guys got a droid that i want to flash to cricket. my problem is that i can not get it into diagnostic mode. i power the cell phone down and i put in usb cable and it automatically boots up into bootloader mode. not matter what i do as soon as i hook up the usb it automatically boots into bootloader. what can i do about this? i know i have the drivers off Motorola website. they are the newer ones iam not sure if this is my issue

Can't seem to get adb to detect the phone -> so no unlocked bootloader

Or.. I've installed the usb driver package from LG. And I can go to the power off-> charger mode, and get contact with the "modem device", or whatever it is they're using, for a short while. But that won't help me get the bootloader unlock routine to work, it just gets stuck in "download mode!!!!", presumably because it needs to do some weird online routine as well, that I didn't know about, or it needs to download something via gprs, or ... and so on. And in phone mode, the serial number/device doesn't show up. (I tried removing the memory card, on the off chance that having the "mass driver" device turning up would mess something up, but no luck.
Anyway. So is there a trick here, to get adb to detect the devices, or to make the "modem device" mode have precedence, or something of that sort? I'm a bit reluctant to try disabling some of the devices, even if that would work, in case there's something else I don't know about being run half-way as well.. will the mode change on reboot, and I'll get stuck with a brick..?
Have anyone else had the same thing? I can run the pc-suite and the lg support tool just fine. But it seems that what happens is I'm able to have the adb tool detect the serial number for a very short time, and then it disappears and I can't connect to it again. Therefore, no bootloader unlock tool init..
I had the same problems back a while ago.
It got solved on the 262-000 Bootloader unlock thread.
I think you need the newest adb and fastboot drivers
and disable the modem in system settings of your pc,
but search for the mentioned thread and look it up there
Hope you get it working

Categories

Resources