i know i've asked this once but it slipped my mind.
where do u look to see if you have the latest spl
When your phone is off, hold camera and power to boot in to the bootloader (SPL). That will tell you.
Related
I've upacked my shiny new XDA Ignito and followed the intructions to install HardSPL.
The TUT says:
<snip>
To verify if you indeed have correct HardSPL on your device, enter Bootloader by pushing the reset button while holding volume down key on the side.
It should display*:
* In case of another HardSPL, the version number would differ!
Code:
…
SPL-1.40.OliNex
</snip>
I don't see this - I just boot into the O2 welcome screen - the update took about 2 minutes - has it failed or is there anyway to confirm the HardSPL has taken? I don't want to install a new ROm until I'm sure I'm not going to brick it....
TIA
Peter
put your phone into bootloader mode and you will see that your SPL has changed to OliNex 1.40.
This information will not show on the normal splash screens.
to put your phone into bootloader you need to turn the power off on your phone, once the device is off, press and hold the volume down then press and hold the power button.
hope this helps
So I followed all the rooting steps did the radio first and all that jazz then chose a rom, Got it loaded up on my g1 but when I reboot it just hangs at the t-mobile g1 screen for.....well, Ever. Help? Please and thank you.
turn off phone
hold home and power, you should be at the recovery menu. wipe and flash a new ROM
if you fail to get this screen, turn off, hold camera and power. you should see 3 skating androids, tell us which radio and SPL you are using
if you fail to get this screen also, i'm guessing you flashed haykuro's SPL before upgrading the radio, and have a very fasionable paperweight
hello..
my x1 just cannot enter bootloader..
when i press power button just show me SE logo after that nothing happen.. just blank screen..
i try do hard reset but nothing happen..
i also try connect with activesync also cannot..
anyone can help me here...
What did you do?, installed a rom without HARD-SPL ? tell us what you did b4 u bricked ur phone
nope.. i do HARDSPL before i flash any ROM..
i follow all instruction..
before this nothing happen.. but this morning when i turn power on my phone just die.. i also thinking what happen to my phone..
i running ROM 826X Windows Phone 6.5.3 build 28011..
If you have Hard-SPL just HOLD power AND volume down (I believe) as the device boots and it will enter tri-color boot screen.
If this doesn't work, then either you have defective buttons, or you did not install Hard-SPL correctly.
so any solution for my phone here..
what need i do..
plss..
to reiterate the above post, dd you hold down BOTH the power button and the volume down key AND NOT LET GO until the tri-color screen appeared?
and if you try to charge your phone, does a red light appear?
harveydent said:
to reiterate the above post, dd you hold down BOTH the power button and the volume down key AND NOT LET GO until the tri-color screen appeared?
and if you try to charge your phone, does a red light appear?
Click to expand...
Click to collapse
yes i do it what ever u say..
but still don't get what happen to my phone..
normal if i charge my phone.. no red light..
it show red and green light..
I think I have just flashed my phone with hardspl 3.56, how do I check which version is currently on. Reason being the flash was very quick, it went from 0% to 100% in a flash.
Get into bootloader, hold camera button in "keeping hold" press reset whole and keep held and it will display Hard-SPL.
stylez said:
Get into bootloader, hold camera button in "keeping hold" press reset whole and keep held and it will display Hard-SPL.
Click to expand...
Click to collapse
Bingo! that worked a treat and it had flashed, Thankyou.
hey guys sorry I did the dumbest thing possible.. i flashed an EBI0 Radio onto a EBI1 Device.. HELP!!!!! the wiki says its fixable if you know how, i would really appreciate it if someone would tell me how. i cannot boot into anything. no recovery.
0
Kipper321 said:
hey guys sorry I did the dumbest thing possible.. i flashed an EBI0 Radio onto a EBI1 Device.. HELP!!!!! the wiki says its fixable if you know how, i would really appreciate it if someone would tell me how. i cannot boot into anything. no recovery.
0
Click to expand...
Click to collapse
Can you still boot into fastboot ? (remove battery if needed to power off, put it back , hold back button and press power )
no i cant. i cannot boot into any menus.
you cant boot into fastboot or into recovery?
sorry man..... brick. at least as far as i could think.
the wiki says theres a way to fix it, does anyone know who wrote it? maybe i could contact them?
Seriously? So you can't access adb/fastboot shells from your computer?
Fastboot is not a menu you access, You need to have the android-sdk setup on your computer, and need to reboot your phone into fastboot:
Take out the battery.
Put battery back in.
Hold the Back Button
Press power button and continue to hold back button.
Device should boot into bootloader, and if you have the right spl fastboot will be enabled.. (i believe thats correct)
Also, did you flash the wrong radio and then continue to flash spl?
If so, your device is bricked. But if you only flashed the radio and it's compatible with your spl you should be ok.
dude, send me your phone, im a professional repair man , i'll even fix it for free XD
The fix way of doing it you may find hard lol but it's called JTAG ^^ read on cyanogenmod wiki
where would i have to send it out too? and some type of insurance would be nice but id possibly be willing to send it out
aBsolutex3 said:
dude, send me your phone, im a professional repair man , i'll even fix it for free XD
Click to expand...
Click to collapse
thatd be great pm me?
bl4cklabel said:
Fastboot is not a menu you access, You need to have the android-sdk setup on your computer, and need to reboot your phone into fastboot:
Take out the battery.
Put battery back in.
Hold the Back Button
Press power button and continue to hold back button.
Device should boot into bootloader, and if you have the right spl fastboot will be enabled.. (i believe thats correct)
Also, did you flash the wrong radio and then continue to flash spl?
If so, your device is bricked. But if you only flashed the radio and it's compatible with your spl you should be ok.
Click to expand...
Click to collapse
I only flashed the radio, and then the CM6 Rom
The radio i flashed was the g1-radio-2_22_23_02 but i flashed it on EBI1 not EBI0
i tried to boot with every key combination i can think of such as camera + power Volume + power Back + Power
EVERYTHING
but it always hangs at the rogers screen
Kipper321 said:
i tried to boot with every key combination i can think of such as camera + power Volume + power Back + Power
EVERYTHING
but it always hangs at the rogers screen
Click to expand...
Click to collapse
Why are you holding down all those keys ._.
hold camera while booting and give us a definitive answer on whether or not it loads a screen.
It does not work.
it stays at the rogers screen