Related
phone is not powering up
hi , I have a htc typhoon (amadeus) based qtek 8100 phone , by mistake I upgraded bootloader to a htc wizard bootloader rom ( IPL/SPL 1.01 ).Now the phone isn't opening turning on or powering up.When connecting to usb nothing happens.Sometimes, it blinks all of the keyboard lights (maybe sometimes that I play with key combinations). How can I repair and put the right bootloader into phone again ?
Note1: I am pressing cam button and connect usb cable nothing happens.
Note2: I can't access to the bootloader screen
.....wow :roll:
LOL that's perhaps the funniest thing i have read on this site
dehjet said:
phone is not powering up
hi , I have a htc typhoon (amadeus) based qtek 8100 phone , by mistake I upgraded bootloader to a htc wizard bootloader rom ( IPL/SPL 1.01 ).Now the phone isn't opening turning on or powering up.When connecting to usb nothing happens.Sometimes, it blinks all of the keyboard lights (maybe sometimes that I play with key combinations). How can I repair and put the right bootloader into phone again ?
Note1: I am pressing cam button and connect usb cable nothing happens.
Note2: I can't access to the bootloader screen
Click to expand...
Click to collapse
I would pose this question in the dev/hacking forum or on the smartphone dev site.
I'm only guessing here, but unless there is a second bootloader image (the Wizard for example has two copies stored in ROM) that can be booted from or otherwise forced to copy over into the primary space, then you might own a brick.
Actually, you may be able to revive it using a JTAG connector and associated flashing software, but that's specific to your device and would be better addressed over in the Typhoon forums. Essentially you would connect a JTAG connector to the EEPROM inside your phone, and the other end connects to your PC. You'd then need software that can transfer a new bootloader image over to the phone.
[off-topic]
Sorry for saying it like this....
But how the **** did you managed to do this?
Were you drunk or something like that...
[ on-topic]
Are you sure that you can't get it in bootloader mode?
What happens if you get it in bootloader mode and just try to flash it again (although your PC said it isn't connected) ?
The problem is I don't know the JTAG connection points for HTC amadeus based phones.Where should I look ?
Phone is not powering or charcing because of these are also controlled by software.Bootloader mode is not available.(I am talking about charcing even not working or opening the phone , bootloader is impossible)
summiter said:
I would pose this question in the dev/hacking forum or on the smartphone dev site.
I'm only guessing here, but unless there is a second bootloader image (the Wizard for example has two copies stored in ROM) that can be booted from or otherwise forced to copy over into the primary space, then you might own a brick.
Actually, you may be able to revive it using a JTAG connector and associated flashing software, but that's specific to your device and would be better addressed over in the Typhoon forums. Essentially you would connect a JTAG connector to the EEPROM inside your phone, and the other end connects to your PC. You'd then need software that can transfer a new bootloader image over to the phone.
Click to expand...
Click to collapse
i've got the same problem with my herald, and dont know what to do!
phone don't start, when i press cam+com mngr+soft reset, nothing happens
even when i connect it to the batteryloader, nothing happens!
please, i need help! i've already searched the forums all over the world (those in english and french...)
Till now i was afraid to admit this but Brother u gave me courage to admit
"I ONCE FLASHED MY TORNADO WITH TYPHONE ROM"
luckily it was in warrenty and sweet talking + innocent gestures worked and i got a brand new replacement but YOU R THE MAN
Dont worry every one screwed up once
keep reading u might find a solution to wake the dead
GOOD LUCK
I have upgraded G4 IPL & SPL on my G3 Vario and now I cant power it on at all, hard reset doesn't work, cant even enter to bootloader It's totaly bricked now. What should I do??? Thanks.
Search the forums for JTAG. Not easy but its doable I understand.
Good luck.
Does the Qtek 9100 have JTAG output on motherboard or do i have to solder the wires??
... or is it able to do it by classic USB cable (for example emulated as COM...) ??? I really dont like to solder the wires
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
edit I don't know.
obion said:
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
Click to expand...
Click to collapse
You can only change your Hardspl from your SD card. You can only initially flash Hardspl from your Pc .
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
obion said:
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
Click to expand...
Click to collapse
You are right, sorry I wasn't clear.
Very bad
you can use jump SPL and then flash hard SPL from SD
badillo said:
you can use jump SPL and then flash hard SPL from SD
Click to expand...
Click to collapse
Providing you had the foresight download and maintain jumpspl on your phone prior to your usb port breaking
but jumpspl can still be "downloaded and maintained" on the device using the mobile browser to access the internet over wifi and/or the data connection...?
so would i be correct if i summarized all the posts in this thread by concluding that a broken usb port is not a hurdle in getting hard spl on your phone?
cuz badillo says hard spl can be applied from sd...and denco7 says that jumpspl is required to get the process started...and i propose that jumpspl can be downloaded to the device by wireless means...
or is this conclusion of mine incorrect?
hmm jumpspl on a sd and copy to the fone?
i honestly think thas jumpspl, and sdcard update cant work together.
but please prove us wrong, it makes unlocking a lot more easy
i want an answer to this topic!!
I have a problem which I need to change hardspl also
thank you very much
You have to have a usb sync for first h-spl 3.29 after that you can read the instructions in h-spl breakdown by Dave Shaw in Sticky ROM dev and surely enough you can flash via SD
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
kyniemxotxa98 said:
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
Click to expand...
Click to collapse
Look HERE
JumpSPL
7Zip to extract zip files attached bellow! Best of luck to you!
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
Bottom line is , you can only upgrade your hardspl via SD Card, you can only hardspl from stock spl via usb connection.
Believe me a lot of smart people have tried for a while.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
You are in the KAISER Forum! You need to be asking this in the Diamond Forum! I only gave you that info assuming you were a Kaiser user! Anything Kaiser will only brick your device for sure!!!!!!!!!
Update your signature to what your device credentials are so people are able to help you better! Take mine and Denco7's for example. If more people had their signatures setup, it would make it so much easier to give out advice!
EDIT: If usb is broken how are you charging the device?
The Diamond does not require the launch of a jump spl, the hardspl package by olinex has all the required files in it. But it must be run from the PC which requires an active sync connection
And Diamond user stop double posting, go to Diamond section and do your research........
Denco7 has answered you in 2 threads yet you still coming back to Kaiser section...
Hi.
today i bricked my kaiser when i tried to install a dutty's rom
been trying to get this fixxed for over 5 hours. nothing worked out.
used kaisdiag.nbh from h ttp://forum.xda-developers.com/showthread.php?t=420683
in both suggested solutions my kaiser wont go further then the Loading page. ( waited atleast 10 mins twice without any success)
used some other RUU installs while in the tricolour screen:
ahmedfikry wm6.5 23549 Tilt UC light rom
KAISER_WM65_OS23547_PP12MB_Sonblack05
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
RUU_Kaiser_HTC_WWE_3.02.405.0_radio_sign_25.70.30.05_1.58.26.20
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_64.08.21_CubeV2_ <== the one wich bricked my phone
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_65.14.06_No_CubeV2_
RUU_Kaiser_TMO_UK_3.31.110.3_radio_sign_25.83.40.02_1.70.18.02_Ship
some other topic sugested to use MTTY.
but that probram says: usb port cannot open.
long story short: im desperate.
can any of u please help me fix my phone ?
its an MDA vario II. model Kais130 P/N 99hcy063-00
thanks in advance.
i'm no expert at recovering bricked phones...
but what i understand is that IF you have a hard SPL (which hard SPL do you have?), then you should be able to recover your device from nearly any situation.
try this...if RUU is not working well, try to flash using the SD card method.
also, try to flash a stock ROM (using RUU as well as using the SD card method). let us know what happens.
Try putting your phone into bootloader, ( press and hold power and camera buttons while doing a soft reset ) once it is in the " tri-color " screen, let us know what it says on the screen.
thanks for your time and the fast response, to both of you.
@#1
i used Pofs hard spl.
and as mentioned above i tried both the RUU way and with my micro SD card.
the SD way only shows me the 'Loading' screen. over and over.
and with the RUU i get several errors. connection errors at 0% and connection errors some later.
some roms just say they wont work on my phone.
and others just reboot my phone.
@#2
i think my phone gets to the bootloader all the time. cause i c no difference when resetting with camera and power button on.
its the tri color screen with the folowing information that shows up:
RUUNBH
Kais130
SPL-1.56.0000
CPLD-8
serial/USB
______________________
the serial shows up when the phone is not connected.. and the USB shows up when its attached to my pc with usb.
Any other suggestions ?
Thanks in advance .
You don't have hard-spl you still have a stock, flash the stock ROM of your carrier from bootloader.
Then follow the noobs guide to flashing.
Thx guys my phone is working like it used to be.
downoaded the original rom from t-mobile again. and again.
now got one wich is working.
thanks for your help.
i was about to throw the brick trough the window.
customer brought HD7 in dead condition he told that he was updating the device and due to low batt it gone dead,no power and no boot mode.so i resurrected in riffbox.now it's hang on htc logo and when in bootmode it gives the info as ;
PD29*** SS-BC(4K)
SPL -5.11.2250.0(134400)MNG
sd sandisk 15193MB
partition info-v211v413
F400
but it doesn't shows "serial" and it doesn't connect to pc.
what should i do,pls help
If you're telling people that you can fix their phones, then you need to be able to fix it without having to come to a forum for help. Especially if you're charging for this service.
Evo4eva said:
If you're telling people that you can fix their phones, then you need to be able to fix it without having to come to a forum for help. Especially if you're charging for this service.
Click to expand...
Click to collapse
thanx for your reply,as i have never challenged u or my customer that i can repair any handset that i have recieved.i have discussed here the fact that its the customer's fone.and your reply is not to the context.Just read my problem and u have any solutions pls advice for the same if not just go to other post.
hi majeed
i have read in another post, that someone else has had the same problem...no seriel or usb on screen, dont worry about it.
once in bootloader just plug phone to pc and do what you have to do...still worked for them.
cheers and have a gr8 day
Thanx bro for reply but i have tried connecting in same condition to different pc's but i get error :260
not sure what your trying to do after you are in bootloader??
you have bootloader 5.xx
therefore you can only install same stock rom or find same but earlier rom to downgrade ur hspl. must be same region too.
cheers and have a gr8 day
Hi jhonny,
i tried to downgrade bootloader according to tutorial of ansar and his rom found somewhere in this forum and got hspl and rspl.first i tried to use rspl of dft but i could not succeed and got an error and then onwards no "serial" in boot loader screen and the result not at all connecting to pc.tried again resurrectin with riff but no use.
majeed said:
customer brought HD7 in dead condition he told that he was updating the device and due to low batt it gone dead,no power and no boot mode.so i resurrected in riffbox.now it's hang on htc logo and when in bootmode it gives the info as...
Click to expand...
Click to collapse
hi majeed, is the unit still under manufacturer warranty
HI MAJEED...
WHAT EVER I UNDERSTAND THAT YOU HAVE HALF BRICKED YOUR DEVICE.
YOU CAN ONLY REPAIR YOUR DEVICE USING GOLD CARD METHOD.
http://forum.xda-developers.com/showthread.php?t=893152