Related
hi,
i have a kaiser that's stuck on the bootloader. i can connect using mtty and get the phone to boot then but that's less than ideal.
does anyone have 5 minutes to talk me through what i need to do to fix this ?
many thanks in advance.
mrdo.
I'm assuming after booting using MTTY it goes back to the SPL after the next soft reset?
Dave
Actually, If you can boot into the OS, Flash a new Version of HardSPL 3.29 by cmonex (it's in the Stickies in the ROM Development Forum).
Ta
Dave
yup -straight back into the spl upon reboot. :-(
is there any difference between 3.29 and 3.29 force usb ?
thanks for your assistance - very much appreciated. lugging a pc around for every time that my phone rebooted wasn't exactly top of my to do list.
c
mrdo said:
yup -straight back into the spl upon reboot. :-(
is there any difference between 3.29 and 3.29 force usb ?
thanks for your assistance - very much appreciated. lugging a pc around for every time that my phone rebooted wasn't exactly top of my to do list.
c
Click to expand...
Click to collapse
I assume you mean the jockyw2001 Hard SPL 3.29 and jockyw2001 Hard SPL 3.29 Force USB?
The difference is to do with people not been able to access USB when in the bootloader.
Can you boot into the OS and flash this Hard SPL by cmonex?
http://forum.xda-developers.com/showthread.php?t=420683
This should fix the problem hopefully.
Ta
Dave
i was having a look at that - that's just an nbh file. is that all that i need to flash hard spl ? as you may have guessed, this is the bit that i know nothing about ...
cheers
c
mrdo said:
i was having a look at that - that's just an nbh file. is that all that i need to flash hard spl ? as you may have guessed, this is the bit that i know nothing about ...
cheers
c
Click to expand...
Click to collapse
Just put the nbh file in the same directory as the KaiserCustomRUU.exe program.
Boot your phone into Windows Mobile, Run JumpSPL (or SSPL) on your phone.
Then Run KaiserCustomRUU.
Ta
Dave
cheers dave.
1) i don't appear to have KaiserCustomRUU.exe
2) how do i run JumpSPL (or SSPL) on my phone opnce i've rebooted.
i'm assuming that there's a sticky that you can point me in the direction of to save you spending too much time on this ...
thanks again
c
mrdo said:
cheers dave.
1) i don't appear to have KaiserCustomRUU.exe
2) how do i run JumpSPL (or SSPL) on my phone opnce i've rebooted.
i'm assuming that there's a sticky that you can point me in the direction of to save you spending too much time on this ...
thanks again
c
Click to expand...
Click to collapse
KaiserCustomRUU is everywhere. (RUU == Rom Update Utility)
If you download an attachment from this page, it will be in the Zip archive: http://forum.xda-developers.com/showthread.php?t=396922
Also follow Post #2 in this link for how to flash a new Hard SPL. (In the FAQ is a link to download the Jump SPL).
EDIT:
In closing follow those instructions in that link but replace the nbh from the jockyw2001 zip you download, with the nbh from cmonex.
Dave
cheers - will give that a go. thanks for your patience.
hi dave,
i'm following these instructions :
1. Plug the device into your PC
2. Copy Jump/Soft to your device. use JumpSPL If you have the "White Screen" issue, if you don't, you can use SSPL-KAIS.exe.
3. Take out your SD card & SIM Card.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe and flash the SPL
i run jump spl from file manager on my device whilst still attached to my usb cable as per step 4.
the bootloader screen appears, as does usb ...
i unplug my device, wait 20 seconds, plug it back in and then nothing happens. is something supposed to happen just because i unplug the usb cable ?
c
mrdo said:
hi dave,
i'm following these instructions :
1. Plug the device into your PC
2. Copy Jump/Soft to your device. use JumpSPL If you have the "White Screen" issue, if you don't, you can use SSPL-KAIS.exe.
3. Take out your SD card & SIM Card.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe and flash the SPL
i run jump spl from file manager on my device whilst still attached to my usb cable as per step 4.
the bootloader screen appears, as does usb ...
i unplug my device, wait 20 seconds, plug it back in and then nothing happens. is something supposed to happen just because i unplug the usb cable ?
c
Click to expand...
Click to collapse
Nothing is supposed to happen, When you unplug "USB" should be replaced by "Serial" and then change back to "USB" when plugged in. (It might not do though ) Just carry on...
Have you Unchecked "Allow USB Connections" before unplugging? If so just run the RUU after plugging back in.
Ta
Dave
mrdo said:
hi dave,
i'm following these instructions :
1. Plug the device into your PC
2. Copy Jump/Soft to your device. use JumpSPL If you have the "White Screen" issue, if you don't, you can use SSPL-KAIS.exe.
3. Take out your SD card & SIM Card.
4. Run Jump/Soft SPL on your device
5. Wait for the bootloader screen to appear and "USB" to show.
6. Right-click activesync, go into connection settings and ensure Allow USB Connections is unchecked
7. Unplug your device from the USB port, wait 5 - 20 seconds, plug it back in.
8. Run KaiserCustomRUU.exe and flash the SPL
i run jump spl from file manager on my device whilst still attached to my usb cable as per step 4.
the bootloader screen appears, as does usb ...
i unplug my device, wait 20 seconds, plug it back in and then nothing happens. is something supposed to happen just because i unplug the usb cable ?
c
Click to expand...
Click to collapse
After you unplug/replug DESELECT 'allow USB connections' then finish step 8.
it was already unchecked.
so when i unplug the usb cable, nothing seems to happen.
am i supposed to reset the device once it's plugged back into the usb cable ? how do i run RUU ?
(p.s i'm assuming that when i run RUU, it will just pick up the nbh file because it's in the same directory ?)
c
mrdo said:
it was already unchecked.
so when i unplug the usb cable, nothing seems to happen.
am i supposed to reset the device once it's plugged back into the usb cable ? how do i run RUU ?
(p.s i'm assuming that when i run RUU, it will just pick up the nbh file because it's in the same directory ?)
c
Click to expand...
Click to collapse
First, re-check "Allow USB Connections" box, and start the process from the beginning (un-checking it when required by the steps).
Just double click the RUU to run. The KaiserCustomRUU will pick up the first *.nbh file in it's directory, it is important that there is only 1 nbh file in this directory.
Thanks
Dave
sorry, it doesn't want to work for me. :-(
i'm assuming that resetting the phone will remove jumpspl from memory and thus invalidate the whole process ?
i have no way of getting into the os without resetting the device.
c
mrdo said:
sorry, it doesn't want to work for me. :-(
i'm assuming that resetting the phone will remove jumpspl from memory and thus invalidate the whole process ?
i have no way of getting into the os without resetting the device.
c
Click to expand...
Click to collapse
At what point to you need to reset your phone? It's not part of the instructions...?
Dave
hey dave,
sorry, i was being a dufus yesterday. everything seems to be working fine now.
have made a small donation - hopefully you'll continue to help other lost souls.
cheers and thanks for your assistance.
c
mrdo said:
hey dave,
sorry, i was being a dufus yesterday. everything seems to be working fine now.
have made a small donation - hopefully you'll continue to help other lost souls.
cheers and thanks for your assistance.
c
Click to expand...
Click to collapse
Thank you very much
Dave
Hi,
i've a big problem with my diamond
it starts normally, but after htc splash screen, it tries to load windows but after 1-2 seconds it restart.
i was using cooked rom gen.Y D2 rev.Y with radio 1.09.25.23
G 52.51.25.26H
i've tried with original rom 2.03 but the problem still remains.
What can i do to resolve this problem?
Where can i find original radio and G (what does it stand for?) to put inside my htc with original rom for probably warranty assistence (i hope)
i've also olinex1.40 spl, how can i remove it?
Thank you in advance
Gianluca
SOunds like a bad flash to me. Try using MTTY to reflash. Should work fine
http://forum.xda-developers.com/showthread.php?t=540290
how can i run this procedure:
Connect Device to PC via Active Sync, Once Connected Uncheck USB Connections,DISCONNECT DEVICE then Reboot Computer
if the device can't start completely?
Flash from your System not the Internal Storage. Read the 4th post.
i can't install drivers on my win7 x64 because i can't follow the first post "how to install drivers" so with the mtty.exe it doesn't find the usb driver
In that case see if you can get into bootloader.
(Reset + Hold Vol Down), this will show the Red, Blue, Green screen showing "Serial"
Then plug your usb cable in and you should get it showing "USB".
You then need to Hard SPL and reflash.
yes i've succesfully installed drive on win7 x64
i've run mtty.exe, followed the instructions, all ok.
then i've disconnected the diamond from usb and made an hard reset (it says press vol.up to restore manufacturer default, vol. down to restore and format movinanand, i press vol. up, and after vol.up again: is it the hard reset or is it another menu?)
but after restart the htc has same problem..it continues to restart by itself
i've decided to return htc to stock software and firmware in order to send him in warranty to delaer.
so, i've installed last official rom htc 2.03, it includes the radio.
Now after that, because system doesn't want to start completely, also after mtty.exe format ecc., the last thing i've to do is install official spl right?
i've found the guide:
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post (pick one of the attachments) in this thread.
2. also download the RUU-SSPL-withoutNBH.zip from the attachments in this post.
3. pick the SPL you want to reflash to (ONLY FOR WARRANTY REASONS), it's a .NBH file, put the NBH in the extracted RUU-SSPL-withoutNBH package.
4. run the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+5. to verify, volume down + reset, see version number on tricolour screen.
that's it.
what official spl have i to install? 1.23 1.34 1.37?
i've tried with all the 3 spl but nothing changed i think, because when i open the bootloader it still saying 1.40olinex
Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide
Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?
I am trying to install 6.5 on my HTC touch HD.
i have looked at the guides, but i am getting nowhere......stuck at 0% on the flashing.
I want to flash Energys rom onto my phone.
Phone is currently
SPL 1.14.000
Radio 1.09.25.14
Rom 1.19.61.1 WWE
what do i need and how do i do it ?
i have downloaded
HSPLWrapper_Blackstone_156OliNex,
SSPL-Manual-TouchHD,
Unsigned_HardSPL_for_Blackstone_OliNex,
Energy.BLACKSTONE.29018.Sense2.5.Cookie.2.0.Apr.18
i have tried on both WinXP and Win 7 Systems, same error 262
1- have you tried installing the htc usb sync drivers manually? -->google
2- do you ever see the tri-color bootloader screen? If not you could try to put it in bootloader manually? you can do that by holding vol down+power button. You do have to turn it of first, and you have to remove the usb cable. WARNING: do not pull out the usb cable while its flashing, you won't be able to start your phone then (you can still flash roms though)
hope this helps
when connecting device to pc does bottom of bootloader (tri colour screen) change from "serial" to usb"? If not you need to either update drivers (see link in Dummies Guide) or open activesync and ensure that "allow usb connections" is enabled in connection settings
If above is all ok then you need to follow guide and get yourself HSPL
If getting stuck at 0% try trouble shooting section and use SSPL
Either way, please post further queries regarding flashing in Dummies Guide thread
Thread closed