Hello,
Yesterday my Diamond had died I think
It was frozen and I did a soft reset, screen stays black and nothing happend anymore.
Pulled out the battery, put it back in, and try to turn it back on. It vibrates after a few seconds but the screen stays black.
every help would be great!
Greetings!
Michiel
It might be low on battery so have you tried recharging it?
when i connect it to the power cable nothing happens, the enter button isn't lighting up.
when i connect it to my pc I can browse to the internal storage normally, but it won't charge the battery.
now I'm really confused...
Take out your battery and sim card and leave it out for about 20 minutes and then put it back. During this time, also have your device plugged in (without the battery).
Reflash Everthing
I've pulled out the battery + sim for more than 30 minutes, reloaded the official HTC rom and still the screen is black.
It starts up, vibrates, makes the start sound but the screen remans black.
Now I want to put the orginal HTC SPL back on it, but it doesn't completes the procedure.
Anyone? thnx again!
I got exactly same problem
this has happened to me twice during the past year. the screen was black, although it did vibrate when I turned it on. both times it fixed by itself overnight, very strange.
what I saw is that both times it happened after a long ride with the car, I suspected that due to the prolonged exposure to air conditioning, when I took it out it condensed on the warm motherboard (it was used as a GPS) and some shortcircuit occured.
Unfortunately, 3 weeks ago, again after a long trip with the car, when I took it out it 'died' in 5 minutes (with 100% battery), did not even vibrate anymore when powered on, and never woke up eversince. It is now in service since the 15th of August, with a status on the website of the official HTC service company in Romania (Cirma Electronics) of: "waiting for spare parts" for 5 days...
My guess is that either the MB or the screen fried because of a design issue which caused the condensed vapors to form on some contacts inside...
It sounds as if the device is 100% operational with the exception that the LCD is out. Correct? Or, have you experienced other problems? Try powering up you Diam, then shine a flashlight directly at the screen. If you can see your interface then you have a dead backlight & need a new LCD. If you do not see the image then the LCD itself is defective {Apparently a common problem} & you'll need a new LCD. Either way you should contact HTC service as you have a 2 YR warranty.
@ cocomic: Where is Your Diam on these trips, A windscreen mount or a console mount? If it's a console mount, most likely you have an air vent blowing directly at it & that's just asking for moisture build up. But, if it was a "moisture" issue as you stated, then HTC would not be fixing it for free. They would see the oxidation from the moisture & say that it's your fault for getting it wet, & charge you out the ass for that part. {That's why ALL devices have LDIs} If you use a windscreen mount, then you have your device sitting in the sun for a long time! Sunlight KILLS LCDs!!! It may be more likely that you burned your screen by having it exposed for long periods. But it's probably just the issue that many people have. If you go to HTCforums you will see a lot of people have LCD issues.
If you have warranty return it to the store.
Humblehippie said:
@ cocomic: Where is Your Diam on these trips, A windscreen mount or a console mount? If it's a console mount, most likely you have an air vent blowing directly at it & that's just asking for moisture build up. But, if it was a "moisture" issue as you stated, then HTC would not be fixing it for free. They would see the oxidation from the moisture & say that it's your fault for getting it wet, & charge you out the ass for that part. {That's why ALL devices have LDIs} If you use a windscreen mount, then you have your device sitting in the sun for a long time! Sunlight KILLS LCDs!!! It may be more likely that you burned your screen by having it exposed for long periods. But it's probably just the issue that many people have. If you go to HTCforums you will see a lot of people have LCD issues.
Click to expand...
Click to collapse
I have a windscreen mount, the air vent doesn't blow directly on the device. furthermore, the sun couldn't have burnt the LCD as the last time it died (for good), it was 11 PM.
the phone is in service and has the online status on their website: "the phone is in the lab, waiting for spare part". this means that whatever the issue is, hopefully it's gonna be fixed under warranty.
nevertheless, I find it appalling that a device built in 2008 has huge design and construction faults causing it to malfunction whenever used in a car with the AC turned on...
I'll keep you posted on the outcome
later edit: update: I've just got off the phone with a secretary at the htc service. apparently the motherboard fried and they ordered a new one. from what she said only the case will remain the same, it may be that the lcd display was caught in the chain reaction . the bad thing is that I will probably have to wait for another week, the good thing is that I will get an almost new phone...
as they didn't say anything about the LDI, it's either that the condensed vapors didn't touch it, only the circuits, or the fault did not come from the humidity... one can only guess...
It may not have been condensation that caused the problem. It could be that your Mainboard had a problem that was amplified by your trips in the car. Either way, you get a factory refurbished Diamond, & that's jus' sweet. I have to call them this week about my Diam because my front cam isn't working. I never really use it, but if it's covered, I might as well make them flip the bill while I can.
no, really, do that... i remember that a few weeks before the 'incident' my rear camera stopped working, too... i never payed too much attention as i considered it to be just a spb mobile shell software issue which would have eventually gone away after a hard reset or something...
you are probably right, my MB was slowly dying, organs failing (i have just watched a house md rerun, sorry )... if you have the possibility to have it checked while it's still in warranty and have the camera fixed while at it, why not?
I'm moving this, as it has no pertinece to the original topic. This link; http://forum.xda-developers.com/showthread.php?p=4476473#post4476473 is a post I started to see if anyone else had these issues. Read the update on the first post
After the replacing of my X1's housing with the new one in the SE Service center I went home gladly with my new X1 housing. I noticed there's an error in signal in my X1 when I was checking my phone at the SE center.. But I thought it was maybe due to poor reception thus I neglected it. (the officer in the SESC say so)
Now I know that there's some new problem arise.. Any idea what might cause this error? the phone can read the Sim card but there is no signal (no connection, no call or no data can be made). i try to check the antenna module, but it seem to be OK (i did not see any problem on it).
the next day i came to the SE center, they said it might be something wrong with the software (since i am used using cooked rom) how come it can make any different while i'm using it before i replace the housing. and they have to take it into the HQ. and guess what, it may take another 6-7 week... WTF
is there anyone having the same problem with me?
Well if you have the tools, you can try openingu p the bottom cover, that little rubber thing where it has the mini sony ericsson logo. Open that rubber up, and you should see a mini screw in the middle, open that up take it out, maybe just give it a quick clean, fit it back properly, and make sure everything is tight and see how that works out.
I've seen/heard a few people having such issue when taking the housing off, and not placing that radio/reception thingy back properly, therefore causing issues with reception.
briian_ said:
Well if you have the tools, you can try openingu p the bottom cover, that little rubber thing where it has the mini sony ericsson logo. Open that rubber up, and you should see a mini screw in the middle, open that up take it out, maybe just give it a quick clean, fit it back properly, and make sure everything is tight and see how that works out.
I've seen/heard a few people having such issue when taking the housing off, and not placing that radio/reception thingy back properly, therefore causing issues with reception.
Click to expand...
Click to collapse
I did it twice, just to make it sure that everything was on their place, also try to flash the ROM, The Radio but still remain the same....
any other suggestion or idea what should I do?
Same problem!
I had disassembled my phone by myself twice; the first time it worked perfectly, the second, unfortunately, it didn't!
I bought a new antenna module for U.S. $10, installed it myself (warranty ended three months ago), walked out of the service centre and voila; I had reception and managed to make a few calls. However, on the way back home, all calls placed while driving dropped every 5km, which means the hand-over between cell towers was failing. The moment I walked home it was dead; no reception whatsoever indoors.
Now the way I see it, this could be due to one of the following two reasons: either the RF power amp failed, which means that most probably the phone needs a new main board (too expensive, not worth it) or something went wrong during the assembly, like the smearing of a sensitive part by skin oil (thus causing a short circuit) or failure to position a connector or multiple ones to connect properly to their respective terminals/connection points.
Upon further investigation, I noticed that my phone wasn't properly grounded; whenever I connected it to a computer to sync using ActivSync or in disk drive mode, I got a small electrical shock (painful though) whenever I touched the phone. This, however, doesn't occur at all when I connect the phone to the wall charger. I disabled USB charging since day 1 of owning my X1i
I believe that the battery cover acts as a ground for the phone electronics; it touches four golden connectors which in turn touch the mini USB port, the GPS/Wi-Fi/Bluetooth antenna, a point on the main board half an inch away from where the loudspeaker is, and the metallic cover placed over the phone RF chips. Failure to ground the phone properly can result in either damaging any of these chips, building up a static charge that affects the antenna performance, or an open-circuit condition for one of the many systems on board.
Since my phone is fully working as a PPC now (PPC functions, Panels, Keyboard, Camera, GPS, Wi-Fi, Bluetooth, etc...) and since I get reception outdoors, and since I have a brand new antenna module, I am guessing that either the RF amplifier is dead, or the housing is ****ed up beyond repair (i.e. it can't be aligned perfectly to get perfect contact on all said points) that it's either shorting a connection, or opening one that is vital for the cellular radio to function properly.
So what to do? Well I forced my phone to do two things:
1. Settings > Phone > Band
- Network type: I chose GSM instead of Auto, as we don't have consumer CDMA in Egypt
- GSM/UMTS Band: I chose the correct band for my provider instead of Auto.
2. Settings > Connections > Advanced Network > Disabled HSDAP
What happened? It worked indoors for a minute, and then stopped working again! Frustrating! So what did I do? I ordered a completely new housing off CNN and will attempt to rebuild the damned thing.
I will update you if I find out anything or reach any results with this phone that I love so much and hate more than anything I have ever hated in my life...
More info!
- During the drive mentioned above, the phone was switching between H, E and G, which means that all three RF chips are, or all components of the whole RF chip if it's one responsible, are working. At one point I got 4 bars of H and call quality was perfect between hand-over failures.
- Before disassembling my phone for the second time, people were complaining about high-pitched static; it can blamed over the mic, the RF (antenna or chip) or humidity levels (which are currently as high as 85%) affecting cellular communication channels.
- Flashing the firmware (R3A Generic UK) and hard-reseting didn't solve the problem.
More Info!
- The battery cover isn't the phone's ground; it's grounded by being connected to four ground points: the mini USB port metallic frame, the GPS/Wi-Fi/Bluetooth antenna ground, a ground point on the main board and the metallic cover over the sensitive RF chips.
- This is definitely an assembly problem. The reception is great outdoors switching between all bands and speeds. On my drive to work today it worked getting G, E, 3G and H all in 4 bars. The signal, however, is completely unstable, jumping from one speed to another. I am more inclinded now to believe that a new housing will fix this problem. Your housing was probably handled poorly at the service centre, which in turn caused this problem.
My advice is to shake them a little bit and see what they will do.
A New Housing didn't fix it!
I purchased a new housing from CNN. It came in good condition. The phone looks brand new now but still no signal. I am sending it in for service. I guess I blew up my Power Amplifiers...
Good luck mate!
melaskalany said:
I purchased a new housing from CNN. It came in good condition. The phone looks brand new now but still no signal. I am sending it in for service. I guess I blew up my Power Amplifiers...
Good luck mate!
Click to expand...
Click to collapse
Same problem haa...
I still waiting for a good news from the service center... I have been waiting for a month..
I wish You a good luck too...
I'm having the same problem. I opened up my phone a few days ago to clean the keyboard. The bottom row wasn't working correctly. Unfortunately after I closed it up again, it wouldn't get any reception (and the keyboard's bottom row was still not working correctly).
So I figured it was the antenna and tried to reposition it. I even removed the rubber layer as described here: http://blog.whitesites.com/How-to-Increase-Reception-on-Sony-Xperia-X1__633958291637656250_blog.htm
Outside I get ok reception, but it's far from stable, inside I get none. And even if I get reception inside, once I pick up the phone, signal drops. So I thought about grounding as well, problem is I even tried rubber gloves and that doesn't solve the problem. I'm afraid replacing the antenna's won't help here and my xperia is dead. Anyone has any other ideas?
Been there too!
I tried the same solution the blog explained. However, I ended up not getting any signal at all. It's only after I purchased a new cellular antenna+buzzer module that the phone started getting an unstable signal outdoors.
Did you notice any small pieces falling off the main board or the housing? It's either a hardware failure or a simple short/open circuit situation that can be fixed in a blink of an eye!
Question
Is there any possible way, hardware or software, to test whether all chips on the main board function properly? I tried the diagnosis tool available here but it doesn't check the chips one by one.
Service Centre
I took my phone to the service centre 6 hours ago. With the new housing on, and new screws that I scored from a secret source of mine, they deemed the phone untouched and serviceable; i.e. it passed for a phone that hasn't been tampered with!
They told me to call back in four days. I will keep you guys updated. Cheers!
I wonder if that'll fix it So to summarize you have:
- new housing
- new screws
- new vibramotor
- new antenna
And those things twice and that fixed it maybe?
I guess it's time for a new phone for me
Vibramotor?
Who said anything about changing the vibration motor? I installed a new antenna + buzzer module; i.e. a new cellular antenna and a new loud speaker (external speaker). The loud speaker is housed within the antenna module. My bad, maybe that part was vague because I never explained it enough.
And yes, it has a brand new housing too. I only installed the lower part though, as the upper part is just fine. Maybe they will fix it man; maybe they won’t I really don't know. I do hope they will fix it though.
I am currently using a backup cheap Nokia and ordered the Sony Ericsson Aspen. If they ever fix my X1 then I can change seamlessly between both phones. If not, then I will just use my X1 as a media/GPS device in my car and an Internet device over Wi-Fi.
Lucky you..... if they can fix yours in a few day... since mine has been in the service centre more than a month, without any news...
they said to me that it will take about 6 week...
What a joke!
The phone remained at the service centre for a week. They called me yesterday, and told me that the phone was fixed and that the total cost was EGP 100 (~U.S. $18). I went over and as soon as I held the phone in my hand to test it, it lost the cellular signal. When placed on the counter, the phone had a constant E signal.
I asked to speak to the manager, who told me that they just reflashed the phone with the latest firmware (Generic UK R3A, which I already had installed). Oh, and before that, he said he was sorry but the phone had a hardware problem and that they don't fix hardware; they only flash firmwares and if that doesn't fix the phone, then the user is pretty much on his own! I refused to receive the phone, so he gave me a refund for my money and promised to have its hardware checked and get back to me in 24 hours!
What a joke, what an f'ing joke! I already regret ordering the Aspen that is due to arrive next week with a friend of mine returning from Paris...
melaskalany said:
The phone remained at the service centre for a week. They called me yesterday, and told me that the phone was fixed and that the total cost was EGP 100 (~U.S. $18). I went over and as soon as I held the phone in my hand to test it, it lost the cellular signal. When placed on the counter, the phone had a constant E signal.
I asked to speak to the manager, who told me that they just reflashed the phone with the latest firmware (Generic UK R3A, which I already had installed). Oh, and before that, he said he was sorry but the phone had a hardware problem and that they don't fix hardware; they only flash firmwares and if that doesn't fix the phone, then the user is pretty much on his own! I refused to receive the phone, so he gave me a refund for my money and promised to have its hardware checked and get back to me in 24 hours!
What a joke, what an f'ing joke! I already regret ordering the Aspen that is due to arrive next week with a friend of mine returning from Paris...
Click to expand...
Click to collapse
OMG...
I do hope that you will get the good news next...
Bad News!
Deep breath... Ok!
Here is the deal: the service centre officially announced that the fault lies within the Mainboard; i.e. my guess that the Radio Frequency (RF) Power Amplifier Chip is toast was correct. They want to charge 90% of the phone's original retail price (which was EGP 4000 = U.S. $700) for a new Mainboard. I replied that that was impossible. They will contact SE's HQ and get back to me on Saturday to see if they can offer any other alternatives.
I guess that is the end of my ride with the X1. I will sorely miss it; it was a great phone while it lasted. Let's hope that the Aspen won't die on me in a year as well...
Hello everyone,
Since a few weeks I have several issues with my Pixel 5, mostly sensors issues (compass, gyroscope, proximity, etc.) but also some weird system software behaviors.
It began mid November when I woke up and realized my phone restarted on its own during the night.
Since then I have these issues :
- Compass not working
- Proximity sensor not working
- Gyroscope working only for a few seconds at start, and then completely stop.
- Phone freezes almost every time I unlock it. It freezes for like 3 to 5 seconds, the colors of the screen are dimmed, and then it finally unlocks.
- When the phone is playing audio content (songs, ring, alarms, etc.) the sound cuts out every 10 seconds (exactly) for like one second and then come back.
- In random moments, the phone will display an error "Process is not responding".
- The small proximity sensor LED is always blinking if I enable "Always on Display" feature.
- Finally, I can't install any Google Play System updates. I perform the installation, reboot the device, but a few minutes after this restart the phone will restart on its own and the Google Play System update will not be not applied (I can perform it again, and again, and again, etc.)
I tried several things : safe mode, factory reset, but I also reinstalled the whole Android 13 image with adb and fastboot. The issues still continue.
I sent the phone to be repaired by Google but they were "unable to reproduce these issues".
They also told me the phone has been damaged by water, which seems weird because the phone didn't had any incident with water that I can remember. I think I had one time the message "Liquid or debris in USB port" about six months ago, I don't understand why the problems would suddenly appear now.
They sent it back without any repair.
I don't know what to try anymore, I was convinced it was only a software issue (and that all the issues were related) but even reinstalling the whole android image didn't solve it. So is it a hardware issue after all ?
Any recommendation on how to process with these issues would be much appreciated. Or maybe I need to give up and buy a new phone ?
Thank you.
It's either water damaged or it's not. Google saw the moisture sensitive indicator(s) showed water exposure. So somehow this happened. If it's been exposed to water the first thing to do is disconnect the battery and allow it to dry out completely then see what you got.
At this late stage the damage may be permanent.
If it was salt water it's already dead. Sweat is salt water... keep 'em in a good case and keep it clean.
blackhawk said:
It's either water damaged or it's not. Google saw the moisture sensitive indicator(s) showed water exposure. So somehow this happened. If it's been exposed to water the first thing to do is disconnect the battery and allow it to dry out completely then see what you got.
At this late stage the damage may be permanent.
If it was salt water it's already dead. Sweat is salt water... keep 'em in a good case and keep it clean.
Click to expand...
Click to collapse
Thank you for your response.
But what I don't understand is why the issues would suddenly appear months after its contact with water, which was only rain by the way.
I am 100% sure it did not had any water incident at the time the issues appeared.
Water damage is insidious which is why manufacturers won't warranty it. Damage can be delayed sometimes taking weeks or months to become apparent.
buying used P5 now due to water damage :-(
Almost went for P7, great device, but I think I'll be fine until the P8 and hopeful Google will have a good trade in value like this year.
$200 for mint P5
$540 + shipping taces etc I believe if you have one od those.
but I think I'll save the $300 for now.. If i had the cash I'd go P7, but P5 is a wonderful device,