Related
Helpppppppp...lol...not sure what to do here. Tried searching the forum for solutions and I am stumped.
WC
Does it get stuck like that everytime or just this time? If it's just this time, try restarting the phone.
If that doesnt work, pull out the battery and put it back in.
tried a rom switch now it just sits there.
WC
Boot into bootloader and reflash the rom.
Tried that it stays at 0%
WC
I can get into the bootloader but it wont do anything after that, this is what it says
kovs110
spl-0.72.000
microp1-787
microp2-707
if you are able to go in bootloader mode, flash with microsd procedure http://forum.xda-developers.com/showthread.php?t=445662
Stops at "loading..."
guap said:
if you are able to go in bootloader mode, flash with microsd procedure http://forum.xda-developers.com/showthread.php?t=445662
Click to expand...
Click to collapse
flash a ROM YOU have previously tested to flash OK
put that rom on your sd card, "kovsimg.nbh"
go to bootloader and flash
PS be sure to give your phone a good battery charging time first, then disconnect the usb cable and remove- reinsert the battery to proceed
same response, just sits @loading...
This is not good I have a feeling.
WC
maybe you already done this, but just in case:
did you do the mandatory Hard Reset after a flash? (clear storage)
Ive been trying everything over here....lol...ahhhhhhhhhhhhhhhhh
WC
Did you Hard-SPL?
Try the Sony Ericsson software update utility:
http://www.sonyericsson.com/cws/support/phones/topic/updateserviceapplication/x1
I want to help you.
I assume you were flashing the X1A ROM and the flash procedure finished. I also assume you successfuly Hard-SPLed your phone before flashing the new ROM. I assume you flashed from your PC (USB cable) and you are under Vista. I asssume you had Touch-IT ROM previously (based on other threads where you have posted)
Please help us to help you:
Don't panic better tell us (describe) what where you doing when your phone got stuck
The x1a wouldnt flash would get to 72 percent and stop everytime. Yes I did the hspl. Yes it was via usb cable. And finally yes I did have the Touch IT rom installed. Now it will do nothing but sit at the sony ericsson screen, or if I enter intot he bootloader it will sit there. Is not charging,no usb connection outside of that.When I try to upgrade from the sd card it gets to the loading screen and thats all.
As I posted earlier the bootloader says this
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
If in the bootloader It will start to flash then give me a connection error and ask to recover, the recovery will completye and it still will sit at the sony ericsson screen or the bootloader screen.
WC
All of your efforts will be useless if you have less than 50% of battery charge: your phone will always refuse to flash.
I suggest you to fully charge the battery to 100% (in other phone or an external charger) and then try to re-flash
After charging the battery, try the sony ericsson update utility linked above
Well I tried one last time to flash the phone with a generic sony ericsson firmware from the sd card and this one is updating, we will see if it completes......cross your eyes,fingers,legs....lol
WC
Well, well. Again same n00b problems Always and always on any htc device, before flashing anything like rom, radio, splash etc, FIRST FLASH HARD SPL!!!! Than you can do everything you want
edit: You have wrong spl version. Verify the screen shows 0.72.OliNex (or 0.52.OliNex MFG) in bootloader mode
Actually i DID do the hspl first,dont know what went wrong with this thing.
WC
borce_razor said:
Well, well. Again same n00b problems Always and always on any htc device, before flashing anything like rom, radio, splash etc, FIRST FLASH HARD SPL!!!! Than you can do everything you want
Click to expand...
Click to collapse
Wild Child said:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
Click to expand...
Click to collapse
To illustrate above post, this, my friend, is the stock SPL. Aka, hard-SPL was not successfully flashed on your device. That is why ROM updates won't complete. I guess you reset you SPL somehow, reflash it.
I got a Upgrade ROM code error, please try again.
any ideas on how to get this to go away and return to my phone?
Hard resets dont work
I have tried the other things listed from the other "I bricked my phone"
Unluckily I'm using Vista and currently don't have an XP ready computer to use. I've removed the battery and plugged the USB cable in and I still get the TRI colored screen with no connection to Windows Mobile Device Center
I did notice that with the memory card installed, the TRI colored screen does go away for a second, but goes into a Loading... and that's all the phone does
from my experience tis happened when the hspl didn't flash correctly. my best suggestion would be to try flashing hspl following the instructions for vista, though it may be easier on xp.
btw, the boot looks for an image on the sd card to flash that's why you get the different behaviour.
i'm not sure if it's possible to flash hspl via the sd card only.
Thank you for the advice
I will try and execute that, but im pretty sure it wont work. the phone wont even connect with my computer
?
when trying to connect to your pc, is it in bootload? if not try that (vol down & power same time till boot screen appears). once you connect it should show in the white area the words "usb" after that try running the ruu.
problem solved!
apparently I didn't realize that I was on the stock 1.14.0000 SPL and that I had to flash the stock rom...
I then flashed the stock rom and re-did the SPL to the Olinex one and re-flashed a cooked rom
Thanx for all the input fellas
Last night my phone froze with Jacks v4.x wm6.5 rom.
i took battery out and put it back in again, and booted it.
it showed me bootloader trying to update my image..
after trying to boot without sd card and cancelling, whic hall didnt work i decided to let it flash.. i had to reinstall but alright...
but after the successfull flash.. it keeps giving me bootloader willing to update..
Ok this morning it worked.. now i have the same thing again.. i reboot my phone, and it gets stuck in bootloader again.. help?
how can i solve this? any ideas?
thanks
ps: without sd-card it is now in bootloader screen saying 'serial'
SPL: 0.72.01 oliNex
*bump* problem occured again..
I have exactly the same problem except mine happened when I tried to restore stockSPL since some cracks appeared in the housing and I'm sending it to service.Any help greatly appreciated!
Hello,
I had the same problem and I solved it.
You have to downgrade bootloader to original version (ruusigned_072stockspl).
Run bootloader and connect USB cable to PC (the "serial" should change to "USB" on screen). Download ruusigned_072stockspl.zip, unzip. Download X1_HardSPL, run it but don't click "next" button! Replace RUU_Signed.NBH from ruusigned_072stockspl.zip to X1_HardSPL folder. Then You can finish installation. Now You have to do Hard Reset and that's all.
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Exa777 said:
Ahem...okay il give alot of details to try to make it clear and easy for you guys so i can get some help
i have xPeria X1 running Hard-Spl 0.72 Olinex
i Flashed my Phone last night and i fell asleep before the update finished...i assume it did but the battery ran out on it, without me taking it out and like reset the phone ( Complete the process )
so this morning when i woke up i tried turning on my phone and it wasnt working..i charged it a little and i got the 3 color screen ..so i reflashed quickly..(didnt think about it...and )with the USB plugged in ...and it failed at like 6% something around that
Every single time i try to flash with the MicroSd
it stop after a few secs and i get some numbers (0018003) with an Error message saying Update terminate update Failed
i tried to flash it with the computer it get stuck at 6% and says it lost connection with the device.
i have a Sandisk Card...ive been flashing Here And there without problem before
its formatted Fat32 and everything i tried other Roms still failing at 6% everytime
Click to expand...
Click to collapse
Try to reflash the rom you was flashing in the first place.
Mayb it is locked, cause it needs a serten file from that rom.
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
ted presley said:
Have you tried to hard reset it?
Fully charged it
And try to enter the bootloader to flash again?
Click to expand...
Click to collapse
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Exa777 said:
yes i did and no sucess
@xMoo
i did that a few times and it didnt work still anyways
what im thinking is that i screwed up something in the Read Only Memory of my phone..else it should allow me to flash to stock at very least...
and also i flashed back to Stock SPL and now i cant Flash it back to Hard SPL
i get a Error message saying Lost comunication with the phone bla bla with a tutorial to reput the phone into boot loader mode
Click to expand...
Click to collapse
try agent47´s task29 that might help
Im trying atm...so far its been 10mins and its stucked at 0%....i cant flash anything =(
Edit... it Gave me update Error 262
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
I Hope this help you!
In one occasion I suffered a similar problem and the issue was that the Memory Card was damaged, and when the Phone Start and tried to read this it "stuck" reading this.
Try to start the phone without the memory to see if this work.
Regards.
Musse_1 said:
are you able to enter the bootloader/tricolour screen ? if so remove sd card.
now on your PC use "X1_RUU_ROM_UpdateUtility" with any ROM image (remember to rename rom img to ruu_signed.nbh), follow steps on ROMUpdateUtility, you will be asked to connect phone (bootloader screen) on 2nd step.
I hope it helps
Click to expand...
Click to collapse
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Exa777 said:
Actually My phone only boot in bootloader mode.
Any any any utility that flashes my phones memory fails
SE update utility= failed stop at 15% and wait forever
Hardspl / Custom RUU... =failed get error 262
Microsd =get stucked OS fail update terminate update failed
so i have no OS now , stucked on Stock SPL and no clues..on what to do next
@ Above poster : i tried flashing with and without my microSD in..it still didnt work i will try a few more times when i get home tonight
Click to expand...
Click to collapse
I've had it.... here is the list of everything i've tried
Mtty /Task 14 0 , Task 28 55aa , task 8
Flashing SD Method
Flashing Stock Rom /Sd Method
Flashing Another Stock rom /SD method
Flashing HardSPl back and for from stock to olinex 72
Using Seus Updater
Take out battery out of the phone for 24h+ to (reset it)
Used Task 29...with no sucess...
Flashing using Cuu Firmware or whatever its called....failed
Every single time i try to flash it goes wrong ... for stock roms it stop at the OS part
Anyways Seus updater put me on spl78..but fails when it comes to the OS @(15%) Like
I just need to Fail Flash one of the Stock rom to go back to spl 0.72
my question is is there any hacked/cooked rom wich include HardSPL like the stock roms does?...that would like flash my bootloader?
Any other suggestion would be greatly appreciated...i dont wanna throw my Xperia Away..when it still can boot in bootloader...i refuse to believe X1's Bricks that easily (ONLY 1 BAD FLASH )
Phones current situation: has no OS, Cant charge it , it turns on itself whenever the USB is plugged in
HardSpl wont flash whatever what i try...so im stucked on Stock SPL eitheir 72 or 78 ..that i can still choose
Phones MicroSD methods keep saying OS fail , (0018003)
Likewise with stock Roms
Mtty...didn't do ****!!!! yet it i got the log like if went trough alot and ****....
lolSEUS Updater get stuck at 15% after updating the bootloader.
Help?
hi guys, i have a problem, ive tried to instal new rom with hard SPL and i had some error during instal, so i canceled it... then my HTC rebooted and is stucked on HTC screen (after circa 15 sec appear in down left corner R, G, D with some nubers and thats it, help me please
bissqit said:
hi guys, i have a problem, ive tried to instal new rom with hard SPL and i had some error during instal, so i canceled it... then my HTC rebooted and is stucked on HTC screen (after circa 15 sec appear in down left corner R, G, D with some nubers and thats it, help me please
Click to expand...
Click to collapse
Please provide better details.
What does your Bootloader screen show for SPL? (Soft reset phone and hold Volume Down before boot starts until you get to tri-colored screen)
1.33.00 or 1.83.Olinex, or?
here is the photo
ttp://i128.photobucket.com/albums/p188/Bissqit/IMG_8156.jpg (remove the space, i cant post links)
and in few mins i give video, how phone behave when i turn it on
bissqit said:
here is the photo
ttp://i128.photobucket.com/albums/p188/Bissqit/IMG_8156.jpg (remove the space, i cant post links)
and in few mins i give video, how phone behave when i turn it on
Click to expand...
Click to collapse
I am at work so I cannot access photobucket.
Can you please just tell me what it says?
so
TOPA200 32M
SPL-1.33.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW (these are in red)
TP MFG DATA
500,542 175,869
188,210 816,201
813,880 Calibrated (in green)
Serial (in white)
bissqit said:
so
TOPA200 32M
SPL-1.33.0000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW (these are in red)
TP MFG DATA
500,542 175,869
188,210 816,201
813,880 Calibrated (in green)
Serial (in white)
Click to expand...
Click to collapse
Where it says SPL - 1.33.0000, if you successfully HSPL, it will say 1.83.Olinex.
I suspect you didn't verify your SPL flashed correctly before you attempted to flash the ROM? If so, this is not good.
Hard reset (Reboot phone and hold both Volume Keys before device starts to boot, and continue holding them untill you get to the white screen, then follow the prompts.)
If you can get back to stock with a hard reset, I suggest you go here and do some reading.
If it gets stuck at the same screen, you will need to find your stock ROM. You can hopefully find it from HTC's site with your Serial Number.
Once you get your stock ROM, connect your phone to your PC and go to Bootloader. Once it displays 'USB' instead of Serial, run the .exe for your stock ROM.
i tried to dl stock ROM from HTC.com, but it says:
Sorry, this software download is not suitable for your device.
im not sure if im on the right side, but there are only 4 options...
i downloaded original update, but from other side and while phone was connected to PC with Red green blue screen i opened the RUU everything went good until status bar (on PC and phone appeared status bar with % as it started installing, but then error) :/
So hard reset was unsuccessful?
Try flashing from SD card.
Right click on the Stock ROM and Extract to a folder.
Place the ruu_signed.nbh file renamed to TOPAIMG.nbh on the root of your SD card and then enter bootloader.
This will initiate the flash and hopefully it won't get stuck at 0%
You can also do this with the .nbh file from hspl.
Perhaps you should try to do HSPL .nbh first, because your OS is locked, it will ONLY accept the exact replacement ROM.
Also, I would suggest taking some time to read and learn about this stuff before diving in head first.
The link I provided previously is very thorough.
Take a look at the MTTY thread after you read about flashing and HSPL.
in bootloader it flash for 0,1 sec and says "Unable to load imagefile" or sth like that
bissqit said:
in bootloader it flash for 0,1 sec and says "Unable to load imagefile" or sth like that
Click to expand...
Click to collapse
Make sure it is 'TOPAIMG.nbh' exactly without quotes.
What was the error you received when you attempted from your PC?
its exactly like that,
it can be any ROM? becouse i have rom with nbh + exe files and with nbh only
bissqit said:
its exactly like that,
it can be any ROM? becouse i have rom with nbh + exe files and with nbh only
Click to expand...
Click to collapse
No, unless you get HSPL to flash first.
If you successfully installed a ROM, it would not boot up because your OS is still locked.
Use this .nbh which is for HSPL 1.83. If you can get this to flash, do the same with HSPL 2.51, then you can flash to any ROM.
i think im lost.
can you please explain me, what should i copy to my SD card and what to do (in oredr)
thanks
bissqit said:
i think im lost.
can you please explain me, what should i copy to my SD card and what to do (in oredr)
thanks
Click to expand...
Click to collapse
Download the SPL 1.83.zip and extract the .nbh file.
Rename it to TOPAIMG.nbh and place on SD card
Enter bootloader mode and pray.
With luck, it will complete to 100%
Then you go back to bootloader and VERIFY your SPL says 1.83.Olinex. (This is the step you skipped before you attempted to flash a ROM, and you have bricked your device as a result)
Without luck, it gets stuck at 0%
Then you need to read up on MTTY to recover your device.
If you think you have your EXACT stock ROM, you can do the same with the .nbh file you extract from that, as previously instructed and get back to stock first before worrying about HSPL.
Basically HSPL unlocks your OS to be able to accept updates. Without it, you can only update from the stock image.
So your choices are, to try to HSPL, or try to get back to stock. Both can be done the same way, in bootloader using respective .nbh file.
I think you are looking to shortcut this stuff and it will only lead you to headaches, unless you take some time to read and learn.
Now, you never did answer;
Did you attempt a hard reset?
What was the error you received when you ran the RUU from your PC?
so i renamed that file, put it on card, card to phone, pushed VolDown and turned on. It flashed with loading and then again "No image file" and back to boot screen
i did few hard resets
error when i tried that "official ROM" was that: Error 294: Invalid render ID
This update cannot be aplied on this device
i try older ROM
Alight, your 294 error indicates its the wrong ROM for your device.
No Image File indicates that bootloader isn't recognizing the file.
Make sure your SD card is formatted to Fat32, you may want to try a 2-4gb card just to be sure. Sometimes larger cards get errors.
Since you can't find your stock ROM, you need to get the HSPL.nbh to load first.
If you can get the 1.83.Olinex to flash, continue the same process for HSPL 2.51 .nbh file.
so i did everything dled you file, formated card, put your file on card renamed turned on phone and now its stucked on loading (if i made something wrong tell me) couse im not sure
i connected phone with pc and try to instal Topaz-HardSPL_V5_00R5_183HSPL but its stucked on 0%
bissqit said:
so i did everything dled you file, formated card, put your file on card renamed turned on phone and now its stucked on loading (if i made something wrong tell me) couse im not sure
Click to expand...
Click to collapse
Well, we got it to recognize the image which is good.
Sounds like you did everything correctly, it just doesn't always work.
I think you have 3 options here;
1. Try to find your stock ROM and flash either from PC in bootloader or from SD card.
2. Read about MTTY and how to use it to flash to your phone and recover, but I still think you need your stock ROM to do this.
3. Warranty return- just tell em it froze, don't mention what you have done to it.
I have one other thing we can attempt here.
Download the enclosed file and unzip it to your PC.
Connect phone to PC and go into bootloader, then run Task29.exe.
With any luck this will force it to load HSPL.
Let me know what happens.
i tried ROMUpdateUtility, task29everything seems to work, but alwways stucks on 0%...
úroblem is, that my phone isnt originaly mine, i bought it from one guy, (couldnt be problem that it is MDA Compact V?)