Related
Hi guys! Need some help, my device is stuck with HardSPL 1.14 because my USB Port on the phone is broken. Any method yet that i can use to flash a 1.56 ROM or upgrade to 1.56 HSPL only using SD Card Method??
Many Thanks!!
MarcWhittle said:
Hi guys! Need some help, my device is stuck with HardSPL 1.14 because my USB Port on the phone is broken. Any method yet that i can use to flash a 1.56 ROM or upgrade to 1.56 HSPL only using SD Card Method??
Many Thanks!!
Click to expand...
Click to collapse
is it 1.14.olinex or 1.14.00000
sorry, 1.14 Olinex
If i'm correct you should be able to flash the hspl by using the SD Card method.
I've have not tested this but they way i'd go would be as follows:
-download HSPLWrapper_Blackstone_156OliNex.exe from this forum
-run the exe in a seperate folder, it will extract it's content to run.
-look inside the folder and see the extracted files, keep the app open for now.
-copy RUU_Signed.nbh from the folder and place in another folder.
-close the app, the extracted files should be removed by it then.
-go to the new folder where you copied RUU_Signed.nbh and rename it to BLACIMG.nbh
-copy BLACIMG.nbh to your phone's SD Card
-enter the bootloader on your phone and it should launch the option the flash as it detects the BLACIMG.nbh
-finish flashing as usual and say some prayers while you reboot your phone
All theoretical here so i'd highly advise to read up in the dummy's thread about hspl/uspl when unsure or unfamiliar with it.
gl
righ, getting somewhere!!! did this method and it worked, now when i go into bootlaoder it says my SPL is 1.56 but it also always says 'Upgrade ROM Code Error Please Try Again' on the bootloader in the middle of the screen?
Not sure what that could be as im no spl expert but might be that the app that does it via usb actually crashes the bootloader to be able to load non htc spl. Since you cant run the app you can flash but generate the error cause it doesnt accept the non htc spl.
There is however also the following mentioned in the dummy's thread:
# Hard reset afterwards. Once or twice- up to you. Twice has been recommended. Turn off your phone. I personally do it right after flashing completes and I see the "Smart Mobility" screen. I just yank the battery out instead of waiting for it to boot up all the way and go through customization process just to hard reset Hold the volume down button and volume up button while you press the power on button. You should see a message saying "This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel." Do exactly what it says...
# You are done!
Click to expand...
Click to collapse
Dont know if you did that already but if not give it go, keep in mind the bold part tho before you loose data.
ill have a look if i can find something, tho can never hurt to look for yourself ofcourse, let us know if you make some progression.
Perhaps this will help, from http://forum.xda-developers.com/showthread.php?t=431217
Anyone having problems with the device entering SSPL automatically, please copy SSPL-Manual-TouchHD.exe from SSPL-Manual-TouchHD.zip attachment to the device and run it. then once the screen is sayingn 1.07.OliNex, run RUU manually. i.e. you launch the Hard-SPL RUU (HardSPLWrapper_Blackstone.exe) on the PC and flash.
*important*: make sure that the USB cable is plugged in and device is synced to Windows Mobile even if doing manual SSPL method.
Click to expand...
Click to collapse
dunno if that last note is an option due to the broken port, but sounds like a good option if you ignore the on pc part. Else perhaps going back to a stock spl would be an option.
MarcWhittle said:
righ, getting somewhere!!! did this method and it worked, now when i go into bootlaoder it says my SPL is 1.56 but it also always says 'Upgrade ROM Code Error Please Try Again' on the bootloader in the middle of the screen?
Click to expand...
Click to collapse
if it says 1.56.olinex then choose the rom u want to flash
then rename the .nbh file dnloaded from the rom cooker to BLACIMG.NBH
place this file in the root of ur sd card.
now insert the sd card nd go to the bootloader.
follow onscreen instructions...
OK, after using the method suggested in post 3 i have managed to get OlinexHSPL 1.56 on it. I then installed Mary One v0.03 using SD card method. It all went AMAZING!!! Thanks doods!! I got my baby back!! Dont need to risk returning it to HTC Repairs now with dodgy spl and rom!!! YAY!!!
MarcWhittle said:
OK, after using the method suggested in post 3 i have managed to get OlinexHSPL 1.56 on it. I then installed Mary One v0.03 using SD card method. It all went AMAZING!!! Thanks doods!! I got my baby back!! Dont need to risk returning it to HTC Repairs now with dodgy spl and rom!!! YAY!!!
Click to expand...
Click to collapse
glad u made it..
Good to hear its fixed, enjoy your device again
Nice work guys, another happy customer.
Thread closed
Hi guys,
want to flash my Wizard from SD-card, but i don't know how to rename thr nbh file. Whats name i have to use and how i have to start the rgu bootloader on the device?
thx for help
Hi, not sure you'll be able to flash a new rom from SD card, unless you have the rom on another wizard. If so you can copy rom from other wizard onto SD card and transfer onto your wizard. Make sure you backup data on SD card because as soon as you load the rom image onto the card it becomes unreadable on pc. Which rom are you trying to load? hope this is of some help
MvSt said:
Hi guys,
want to flash my Wizard from SD-card, but i don't know how to rename thr nbh file. Whats name i have to use and how i have to start the rgu bootloader on the device?
thx for help
Click to expand...
Click to collapse
Unfortunately renaming the nk.nbf doesn’t work with the Wizard.
I discussed how you can make an SD image for backup and uploading “here in this thread”.
Rom flash from sd
ROM flash from SD/MMC: Without needing 2nd device
here is link
http://forum.xda-developers.com/showthread.php?t=393370
go for it
My Wizard 200 is also Dead after downgrading version 2 to 1
so now it is totaly dead ..even not go in bootloader mode also..
so if any one know how to alive my phone than please reply me
thank you
(india)
Thank you for the link I never found an alternative, I will have to look in to this.
swapniladsure said:
ROM flash from SD/MMC: Without needing 2nd device
here is link
http://forum.xda-developers.com/showthread.php?t=393370
go for it
My Wizard 200 is also Dead after downgrading version 2 to 1
so now it is totaly dead ..even not go in bootloader mode also..
so if any one know how to alive my phone than please reply me
thank you
(india)
Click to expand...
Click to collapse
First THX for this link, but it's not what i'm looking for.
Some time ago i read about only to rename the ROM.nbf into a nother name (don't know the name, i'm looking for), copy this to the SD-Card and start manually the RUU.
Than after the RUU is started you have to press the green phone button and the wizard will be flashed from SD-Card.
Know I'm looking for the name i need for the .nbf file...
As far as I know what you’re asking for can’t be done, if you find a way please do post it.
The link I posted above was the only way I knew of.
double post
Ok, I'll do.
If i don't find out the name i try your way ,
or i install MS Win Xp again...
or wait till i get my diamond and put the wizard back in the rack.
Hi`Guys
for the last few days im having an serious rom problem with my Sony Ericsson X1 sines i was looking for an good 6.5 rom that fits and works smooth with my X1 i found an cooked 6.5 rom belong to HD2 aka Leo2 and i reveiw it and i like it so i charged my phone to the full and unlock my phone using "HARDSPL Tool" after that i upgraded my phone with the new rom ,i like it at the first but after some times i faced alot of hangs and bugs within the rom besides the rom overload the processor that would make the phone runs slow so i had to place back my original rom so i used Sony Ericsson Update service "SEUS" to replace my current rom and when i runed the update it asked me to place back the stock SPL and i did and runed the update again but it said that i have he latest software update so i tryed to go all the way around and use the traditional way to downgrade my phone but here is the problem when ever i start the downgrade prosses it gives me update error number {[260] connection} the update stop and start the recovery prosses ,then i tryed to reunlock the phone but it gave me the same error ,so i tryed to get smart and i stop using the computer for the downgrading and moved to flashing methods farmatted my micro-sd to FAT32 placed the required nbh file named with Kovsimg but when i bootload my phone it stops at the loading part without going throw the checking prosses then done the same with the the SPL but the same it stick at the loading stage ,i start to get hopeless my last option was to use the MTTY Tool but it only formatted the rom without flashing the phone
so now im using 20% of my phone option to avoid bugs or hangs and my phone stick with bad 6.5 rom protacted with StockSPL that cant be changed
so guys any one faced the same problem ? plssss help i really feel like my phone its on handicap status
pls help me...
Try to install this:
http://forum.xda-developers.com/showthread.php?t=606799
drnjstj said:
Try to install this:
http://forum.xda-developers.com/showthread.php?t=606799
Click to expand...
Click to collapse
im not looking for a rom i want to release my phone from it hanging in rom updating it stops at 0% when i use the computer and at the loading screen when i use the micro-sd
but thanks for ur help anyways
error_man said:
im not looking for a rom i want to release my phone from it hanging in rom updating it stops at 0% when i use the computer and at the loading screen when i use the micro-sd
but thanks for ur help anyways
Click to expand...
Click to collapse
good info that
I read often that it might be solved with one of the following
1. Remove your SD card, run the HardSPL again, then reinsert the SD card with your kovsimg file and it should work
2. reinstall active sync via .msn
3. change the usp port and the data cable
4. disable firewall and antivir
...
But item 1 is reportedly the main reason for most of the error 260 connection failures.
good luck
DrakenKorin said:
good info that
I read often that it might be solved with one of the following
1. Remove your SD card, run the HardSPL again, then reinsert the SD card with your kovsimg file and it should work
2. reinstall active sync via .msn
3. change the usp port and the data cable
4. disable firewall and antivir
...
But item 1 is reportedly the main reason for most of the error 260 connection failures.
good luck
Click to expand...
Click to collapse
sorry it didnt help it showed me a new error with the number of [262] now and the upgrade i think the problem its within the phone it self
thanks for the help tho
error_man said:
sorry it didnt help it showed me a new error with the number of [262] now and the upgrade i think the problem its within the phone it self
thanks for the help tho
Click to expand...
Click to collapse
how did you try the update? w or w/o sd card?
if with card: did you check if the card is formatted as FAT32?
did you try it with a custom rom? maybe try a stock rom (pavelx1 thread) first
pls try to find some aid in hard-spl unlocker... thread
sry, but from here it's like looking for a needle in a haystack...
DrakenKorin said:
how did you try the update? w or w/o sd card?
if with card: did you check if the card is formatted as FAT32?
did you try it with a custom rom? maybe try a stock rom (pavelx1 thread) first
pls try to find some aid in hard-spl unlocker... thread
sry, but from here it's like looking for a needle in a haystack...
Click to expand...
Click to collapse
my dear friend i thank u so much for ur close support to me and my problem
i tryd the activesync first and after the update start on the computer and my phone the update stops at 0% on the computer and the phone as well then the update stops showing error #[262] update error then start the recovery prosses and i formatted my micro-sd to FAT32 and load it with the required file but when i bootload it start the update but stops at the 1st prosses the loading prosses and never move next to the checking and so on
i believe my problem it had something to do with the SPL the rom its locked with the StockSPL that not allowing the update to happen or to get unlocked with the HardSpl
error_man said:
my dear friend i thank u so much for ur close support to me and my problem
i tryd the activesync first and after the update start on the computer and my phone the update stops at 0% on the computer and the phone as well then the update stops showing error #[262] update error then start the recovery prosses and i formatted my micro-sd to FAT32 and load it with the required file but when i bootload it start the update but stops at the 1st prosses the loading prosses and never move next to the checking and so on
i believe my problem it had something to do with the SPL the rom its locked with the StockSPL that not allowing the update to happen or to get unlocked with the HardSpl
Click to expand...
Click to collapse
it's of no use if we can't solve it ... and I'm nearly out of ideas
pls read this, hopefully it helps
DrakenKorin said:
it's of no use if we can't solve it ... and I'm nearly out of ideas
pls read this, hopefully it helps
Click to expand...
Click to collapse
it toke me really long time to find the file in other site other than rapshared and it didnt worked i tryed also newer StockSPL also the same the phone its not updating im getting really helpless here
Have you ever tried to put your phone into the bootloader mode and try to hardSPL again?
Are you currently using win XP? Don't use Win 7 or Vista.
ted presley said:
Have you ever tried to put your phone into the bootloader mode and try to hardSPL again?
Are you currently using win XP? Don't use Win 7 or Vista.
Click to expand...
Click to collapse
yeas my friend i tryed it many many times it didnt work it give the same error [262] and i dont really trust windows 7 or vista with my phone upgrade i only use windows Xp for such things
thank u for ur support n help...
Try installing the newer SPL and then install hard-spl on a different computer without your sd card in the phone.
NeoXerO said:
Try installing the newer SPL and then install hard-spl on a different computer without your sd card in the phone.
Click to expand...
Click to collapse
do you have any idea where i can find an newer SPL ? hope if it is not on rapidshare server
http://forum.xda-developers.com/showthread.php?t=431218
its on XDA server..just click on the first link down on a list of downloads..it reads: X1_HardSPL_v1.zip
hope I cud help
error_man said:
do you have any idea where i can find an newer SPL ? hope if it is not on rapidshare server
Click to expand...
Click to collapse
sounds like he means newer stock spl
not sure if the latest stock roms already have 0.78spl, but you will get it it you flash an older stock rom (0.52) and update via SEUS
cheers
circleofomega said:
http://forum.xda-developers.com/showthread.php?t=431218
its on XDA server..just click on the first link down on a list of downloads..it reads: X1_HardSPL_v1.zip
hope I cud help
Click to expand...
Click to collapse
i didnt help too its the same one the i first used it that got my phone stuck..i really feeling helpless but i thanks u for ur hard work in helping me to get over my problem thanks
DrakenKorin said:
sounds like he means newer stock spl
not sure if the latest stock roms already have 0.78spl, but you will get it it you flash an older stock rom (0.52) and update via SEUS
cheers
Click to expand...
Click to collapse
can u pls tell me where i can find any new and old stocks..cuz SEUS is telling me that i have the latest software update
error_man said:
can u pls tell me where i can find any new and old stocks..cuz SEUS is telling me that i have the latest software update
Click to expand...
Click to collapse
sure
check pavelx1 rom thread in the sticky section
hes got R1-R3 country specific stock rom collection
1. Download stock rom for your country and flash
http://forum.xda-developers.com/showthread.php?t=475482
2. follow instruction: how to restore Stock SPL for warranty reasons from this post
http://forum.xda-developers.com/showpost.php?p=2710557&postcount=1
3. use SEUS to update your stock rom
YOU MUST FLASH STOCK ROM BEFORE RESTORING STOCK SPL
kjk said:
1. Download stock rom for your country and flash
http://forum.xda-developers.com/showthread.php?t=475482
2. follow instruction: how to restore Stock SPL for warranty reasons from this post
http://forum.xda-developers.com/showpost.php?p=2710557&postcount=1
3. use SEUS to update your stock rom
YOU MUST FLASH STOCK ROM BEFORE RESTORING STOCK SPL
Click to expand...
Click to collapse
i guess your way its the only thing that i didnt do yet but the problem is that all thouse stock roms are uploaded to rapidshare and i cant download it from there just hope is any body could tell me other site that i can download thouse new frimware or latest x1 stock rom
Hi guys!
I'm a new user and i wanna flash for the first time my opal t2223 with the pajerm's rom lite 21697 but i've some question:
1. i've downloaded a stock rom for this phone, for safety, and i found the .nbh file and a radio file,but in the rar file of pajerm's rom i found just the .nbh file, i need also the radio file to flash this rom on my phone or i can flash it without?
2. during the flash process sim card and micro sd must be inserted in the phone or is better that i plugout?
3.some backup of text msg,contacts and other from wm 6.1 created with spb backup work correctly if restored in wm 6.5?
thank you for helping me and sorry for my english
And sorry if i've posted in the wrong section XD
Rom flashed thx pajerm!!!
franciccio said:
Roma flashed thx pajerm!!!
Click to expand...
Click to collapse
So, did you manage to flash it without finding Radio?
If you may, post your steps as you did it so others can make use of it. And hope you enjoy your new OS
pajerm told me that the radio is part of the software that runs from near the peripheral and the interface with the operating system, it is not necessary to update the radio when you change a rom, because each type of PPC has its own radio i guess, infact i haven't found any problem during flashing operation by following guide from the first posts
I hope I was clear enough
wbadry said:
So, did you manage to flash it without finding Radio?
If you may, post your steps as you did it so others can make use of it. And hope you enjoy your new OS
Click to expand...
Click to collapse
i havent done anything extra for the radio, flash normally as in the posts... works fine so far...
Hi, can you help me with how to remove the Hard-SPL to upgrade to the original ROM for HTC Touch Pro 2. I'm from Bulgaria, the phone is not locked to an operator (AT & T Orange), etc. What files will I need and how. I also want to download the original Rom from the site of HTC. Thanks in advance!
http://forum.xda-developers.com/showthread.php?t=550131
All info you need is here.
One note from my experience: first downgrade to original rom then install original spl. I had an issue, it was bricked, but all it needed was to one more time upgrade original rom.
You mean that you must first install the original Rom (I could not download it from HTC's site can help you). And then correct me if I'm wrong:
First you say to install the original ROM.
2nd to download RhodiumSPLRelocker_079SPL.zip unzip it and run. Exe
3rd Stock_SPL_Restore_084.zip to download and in the same way as putting a new ROM to choose it (unzip it first)
Do I need to do Hard Reset at any time? And maybe a little help otkade to download original ROM.
I did this from the link you gave me in boot loadera get out this Oninex, then I load again ROM-a which had previously tried to put my original and gave me an error
The instructions say to flash the stock ROM before you re-lock SPL.
I have failed to: (i already made a re-lock SPL ... now what to do: (
I am still with Energy ROM, which I had to do before re-spl .. in boot loadera now I do not go Olinex 0,85 as before ... what to do?
Sorry for my bad English!
ivailo0 said:
I have failed to: (i already made a re-lock SPL ... now what to do: (
I am still with Energy ROM, which I had to do before re-spl .. in boot loadera now I do not go Olinex 0,85 as before ... what to do?
Sorry for my bad English!
Click to expand...
Click to collapse
i don't think you can re-lock your phone with custom rom on your phone but what you do is hard_spl it (if spl re-locked) then
task 29 ----> install stock rom ----> re-lock spl
good to go
Isteglih his RUU_Rhodium_S2_HTC_Europe_2.07.401.1_Radio_Rhodium _4.49.25.91_Signed_Ship
this is the right Stock Rom correct me if I'm wrong. Inastaliram it and to 0% gave me an error. - 294 Invalid Vender ID.
But it's not e what I need.
I'm not too far into things ...
Please help, now I can not get no ROM, and this olinex do not write anymore. and gives me an error any attempt to put the new ROM. Now when I work under the Energy ROM ...
Hi
Before flashing another rom, please use the tool called task29. get it here http://forum.xda-developers.com/showthread.php?t=649191
Check here for another rom for your device http://rapidshare.com/#!download|33...dio_Rhodium_4.49.25.17_Signed_Ship.exe|180171
or here http://shipped-roms.com/index.php?category=windows mobile&model=Rhodium
use the SPL relocker tool LAST
Good luck!
Hello, thank you for the help you gave me, but I think we still have a problem (task29). Do the following:
1 - http://forum.xda-developers.com/showthread.php?t=649191 here I lost my task29.zip.
2 - unzip it, inside there was task29, had ROMUpdateUtility.exe. ROMUpdateUtility.exe and opened as follows next .. next .. me and sticks to 0%.
In the above post I mentioned that yesterday I did relock SPL before I know that I need to do this first (I do not write now in olinex boot loadera). I think from there
:-( you're in bad way. look for some help here http://forum.xda-developers.com/showthread.php?t=550540
The solutions mentioned above will NOT work, because you don't have hardspl installed.
Flash Hardspl again and then restore to stock rom and spl.
Guessed for it, but waited for someone to tell me. I will use this thread http://forum.xda-developers.com/showthread.php?t=550131 and you will get new and will write what happened. Thanks!
I made myself a new Hard-SPL. After I did task29. After you've installed the new ROM. After I did Relock-SPL. Now everything is OK.
Many thanks to all who helped me!
ivailo0 said:
I made myself a new Hard-SPL. After I did task29. After you've installed the new ROM. After I did Relock-SPL. Now everything is OK.
Many thanks to all who helped me!
Click to expand...
Click to collapse
This is what i told you to do in Post #7 ..... i guess you didn't read it at that time but anyways glad to know your problem is solved
You are right. Thanks again
ivailo0 said:
I made myself a new Hard-SPL. After I did task29. After you've installed the new ROM. After I did Relock-SPL. Now everything is OK.
Many thanks to all who helped me!
Click to expand...
Click to collapse
Bravo! so you how many of your fingers still have finger nails? lol
Baptism by fire, eh? Nice time.
ivailo0 said:
I made myself a new Hard-SPL. After I did task29. After you've installed the new ROM. After I did Relock-SPL. Now everything is OK.
Many thanks to all who helped me!
Click to expand...
Click to collapse
How did you MAKE a new HardSPL ? When I did this mistake, I had to buy another HardSPL to unlock it because the license I had for the first time was already used up.
jfandl said:
How did you MAKE a new HardSPL ? When I did this mistake, I had to buy another HardSPL to unlock it because the license I had for the first time was already used up.
Click to expand...
Click to collapse
he already had the same phone Hard-SPLed. the license works for the same phone forever. a different phone is different.