AT&T Tilt 8925 - At a Loss - please help - Tilt, TyTN II, MDA Vario III General

I have spent 2 hours looking at forums and none have solved my problem. I will try and state as best possible of what is and what has happened.
When I take the battery out and plug in the charger, it displays a red light at the top left. Sometimes, depending on how long I wait, when I put the battery back in, it either has no lights or turns to Orange. Once, when it turn to Orange, I did a soft reset and it went to the white AT&T screen and just stayed there. I hit the soft reset again and it went to the Red, Green, Blue and White Screen. After seraching, I found out that it was called the bootloader screen. But on mine, there is no writing whatsover, like serial or whatever...just the color bars. When I try and plug it up to the usb on my computer I get nothing. It looks like it will not soft reset unless I put the battery back in and the light goes Orange, that's the only timw it will do it. If I put the battery in and it turns the red light off...it will not do anything...nothing.
Can somebody PLEASE help me try and figure out what to do here? I don't think I will be able to load anything on it since nothing happens when I plug in the usb to the computer.
Thanks for taking the time for listening. And also, I have not loaded anything for 2-3 weeks now onto the phone and this just happened late last night. Thanks again!
Monty

Update...had the battery out and nothing plugged into it for about 30 minutes. Put the Battery in, it powered up, went to the first AT&T screen and immediately went back dead again. If I put the battery in and hook it to the charger, it doesn't charge...so I don't think it is the issue with a dead battery...maybe?
PLEASE HELP...Can't really afford another phone right now.

Sounds like you need a new battery.

But should it power up with the phone charger plugged in...good battery or not?

I don't think so, these phones are pretty strange when it comes to bad batterys. Hopefully you know someone with a tilt that you can swap batterys with.

Even if the battery is dead, it should still start the phone and not go into boot loader. Do you have the OEM or a custom ROM? YOu may also want to try and hard reset. Press and hold the 2 dash buttons down (the ones above messages and internet); the while holding them down, insert the stylis into the reset hole, and let the phone reset. once it resets and goes to the hard reset gray screen, let go of the dash buttons. Then when it asks if you want to reset, press the green send button and let the phone hardrest.
If the battery is dead, and will not charge, the phone should not turn on (at least that was my experence, when I had a bad battery). This is just very wierd

Update #2 - I just went to Batteries Plus and they checked the Battery and said it had absolutely nothing...maybe those times it came up completely drained it.
So I forked out $40 bucks for a new battery and they told me to fully charge it before use. So I put it in the phone, plugged the charger into the phone and it looks as though nothing is happening because there are no lights on whatsoever...itsn't there supposed to be?
I have the OEM Rom.
Should I try the hard reset even though the new battery is not fully charged yet?

I wouldn't.
Your phone might be so dead that it doesn't charge the battery, I've seen this in laptops and other devices.

Update 3 - Since it looked as though nothing was happening, I tried the power buttong and nothing...so I took the battery back out, and the red light came on with the charger only plugged in. I tried to put the battery back in a few times and I finally have an orange light lit up while the battery is in and pluuged up to the charger...does that mean it's charging? The light will turn green once fully charged, correct? Anyone know about how long that would take if that's the case?

turn it on, it's a lithium ion battery, it doesn't have a memory.

It's plugged into the charger, orange light is on, but when I press and even hold down the power button, nothing happens????? UGGGHHHHHH

Should I try a soft or hard reset? Want to ask before I do.

Okay...I did a soft reset and it boots up now....for 3 time it went all the way to the main screen and then rebooted itself...now when it rebooted it went to the Red, Green, Blue and White bar screen. There is no writing on the screen, just color bars. Any suggestions?

Just to say... I don't think it's a good idea to have the phone plugged in without the battery...

Related

AT&T Tilt broken screen

My sister's boyfriend gave me his Tilt because he bought a Blackberry. Long story, he broke the first Tilt, they replaced it for him and he broke it again and he was told it would cost $500 to repair... so he bought the new phone and gave me the Tilt for free. So here's the deal: it will charge and turn on.. but only stays on for a few seconds. The LCD is cracked... pretty obvious. However, I was wondering if there was another problem since the phone won't stay on or if it's typical for it to turn off with just a broken screen. This is basically the sequence of events:
Hit the power button, a green LED on the left of the ear piece lights up and the phone vibrates for a second.
The screen then lights up but doesn't display anything obviously... other then the black liquid and white back lighting.
The screen stays on for about 15 seconds, shuts off, the keyboard lights up for a VERY quick second and then that's it... nothing else.
I'm wondering if I should try and find a replacement screen or if there is something else wrong with it. I saw the screen on phoneystore.com a while back but the site has said it's down for maintenance every other time I checked.
Other Info - I took the back cover off and above and slightly to the right of the camera is a black dot that says "VOID".
Any help is appreciated.
Thanks.
Normally you only get the vibrate if you are turning on from the completely off position.
From the completely off position you have to long press the on/off button - is this what you are doing?
In any case, it's difficult to tell if there are any other problems. You could try tracking down on this site, one of thoses applications that lets you see / control the device from your PC.
That $500 figure is I assume for someone to do the repair for you, 'osc the screen would not cost anything like that.
Mike
Also that "void" dot you see I think is just over a screw and if you go inside your tilt you'd have to poke through that and it would void your warranty. So thats not because the screen is broken.
well, i don't have to hold it long before the green LED comes on and the phone vibrates... then the screen shuts off and i have to turn it back on again. it doesn't seem like it's staying on.
the $500 was from AT&T to have them fix it... so yes.
and thanks for the reply on the "VOID" - i thought it maybe had something to do with water damage or the cracked screen.
Have you tried turning it on with the wall charger plugged in? I thought I had seen my sons just shut down like that when his battery was pretty much dead and I was trying to turn it on.
Well, i was bored waiting for work this morning so i decided to put the SIM from my phone into the Tilt... I turned it on with my SIM in and it stayed on for longer... then I heard a little tick and kind of "whooosh" sound which I'm assuming is the start-up sound. Then nothing for a few seconds... then there is this "kerplunk" noise.. then the amber LED on the left of the ear piece starts flashing and then the phone starts vibrating and making a high pitch ring... the vibrating seems to be in a patter. Then I hear what sounds like it may be a shutdown noise and the phone is off again. However, the back light on the screen remained on the entire time. It might that with the SIM in it works, but the battery is dead so it turns right off? I have the wall charger here somewhere so I will have to try that after work. I will let you know the results.
most likely the sounds that your hearing are just an alarm clock going off. my guess is that the screen is the only thing that is really damaged. you can look online at ebay and get replacement screens with the tools necessary to replace the screen for under 100 bucks. i think that would be a good deal for you... keep us updated on the status
if possible if you are going to replace the screen from ebay you should take piectures. it would make a very nice guide for the noobs
yeah... i will definitely take pictures when i do it. i hope it's just the screen. i don't know why it won't stay on tho... i'm still trying to find the charger for it. i don't remember where i put it. i will keep you posted tho.
You can charge it with any USB mini type B lead plugged into a PC. You probably have one somewhere for a camera or other phone.
Don't be fooled by the shape of the socket on the bottom of the phone, it still fits.
mikechannon - do you know the name of any of these apps? i'm not able to find anything..
good news tho.. the phone now stays on and i am able to receive phone calls. i found a screen w/ tools for $70 shipped on e-bay. i want to try what you mentioned mike, hook it up to the pc. i just want to make sure everything seems okay before i buy a screen.
try my mobiler
okay... so i put the new LCD in and it works.. to an extent. it displays the at&t splash screen, then the 3G animation, then gets to the windows mobile 6.0 splash screen and it hangs there for a few seconds then shuts off. i thought maybe it needed a new battery because it wouldn't stay on before so i ran to the store and got one and it's charging now. i'm going to wait a few hours and try again...
when i try and turn the phone on when it's plugged into the charger it seems to hang on the at&t screen... this doesn't seem normal.
also, when it's not plugged in and goes through the screens, on the at&T screen it looks like it's showing RGB values or something in red text in the bottom right corner of the screen. is this normal?
Sorry, did not see your 3/22/08 post.
The RGD values in RED are normal (info about radio version etc) if you are starting from the off position or have just done a soft reset.
I'm not sure why it is hanging at the point it does. I am assuming you have done a hard reset? (you may have said - but I have not read back all the posts)
Mike
nope... no hard reset.
when i turn it on while it's plugged in the amber LED on the ear piece goes out for a minute, the AT&T screen comes up then a few seconds later the amber LED comes back on and it just stays there.
i was able to get it to get past the windows mobile 6.0 splash screen but it says 6 new notifications/alarms, then starts buzzing and ringing and turns off. one time it said battery was critically low or something. i want to assume that it is charging because the amber LED comes on.. but who knows. i would hate to have to give up at this point.
jbradt said:
nope... no hard reset.
when i turn it on while it's plugged in the amber LED on the ear piece goes out for a minute, the AT&T screen comes up then a few seconds later the amber LED comes back on and it just stays there.
i was able to get it to get past the windows mobile 6.0 splash screen but it says 6 new notifications/alarms, then starts buzzing and ringing and turns off. one time it said battery was critically low or something. i want to assume that it is charging because the amber LED comes on.. but who knows. i would hate to have to give up at this point.
Click to expand...
Click to collapse
Actually that all sounds pretty normal. Yes expect to get a whole bunch of notifications that have accumulated and never been cancelled. When they come up try to cancel them quickly - just choose dismiss. Don't be surprised if there are so many that it crashes the device and you have to re-start possibly several times until eventually you get past all those notifications!! This also happens when you restore a backup - I have seen my device go absolutely bananas with many many notifications and a crash is not unexpected.
If the battery is not charged give it a good hour of charging before trying again. One thing that puzzles me is that if you have the amber light that shows charging (good) then why does it give you a message saying battery low?? Normally you will never get that notification whilst on charge.
Mike
mike,
thanks for the replies. i was able to dismiss a few of them earlier and then the battery message came up and the phone turned off. it wasn't plugged in at the time. however, i left for the day and left it plugged in for probably 7 hours or more...turned completely off...and i came home and it got past the windows splash screen again and then said the main battery was critically low and turned off. can't get it to stay on now. i'm lost...
it seems like my only other option is to try a new charger.. but if the LED comes on it would seem as though it is working. i checked all of the contacts where the battery goes and like i said earlier, i bought a new battery this morning. i really don't want to take it apart again. while it was apart i did my best to clean the any dust or other build-up. i guess i could try and charge it on the computer.
my phone does the same thing I accidently dunked about an inch of it the top of the phone into a cup, thought it was ok after i let it dry off and it would boot up but I still can't get the phone to really charge, the orange light will go on but the battery never charges and I used to get the red critical battery warning. Ive tried a bunch of different chargers but still nothing just gets to the second splash screen in duttys rom and turns off now. Hopefully you can get your up though, just wish i could get 30 minutes of battery to get it back to stock rom and everything so i could send it back as the bottom never got wet and the water check under the battery is still white.
Mmmm. Well sounds like there is a hardware charging problem. Pity you don't have one of those chargers where you can dock a spare battery to charge it up. It would be a hassle though if that's the only way to charge the battery. There are ways to charge the battery by wiring the battery directly to a set of AA batteries or a charger, but that would not solve the problem in the long run.
There are companies that will replace the USB connection on the M/board but that would be to assume that is where the fault is - and I'm not convinced it is. The fact that the orange charge LED comes on suggests the USB connection may be ok and that it may be the battery connection block that has a broken connection. This is not easy to repair if at all. I have seen one reported case where that block with the gold connectors had broken connections and a repair company could not resolder all the connections.
One thing to try regarding the battery connector block. With the luck of the Gods it might just be that one or more pins is not making a good batter contact. Try cleaning the pins and battery contacts. (A bit of a forlorn hope though)
Mike
well, good news!
i left it plugged into the computer all night and turned it on this morning and it went through all of the alarms... i dismissed them all. it then stayed on!!! so i went to the system settings and looked at the battery life and it said it was at 100%. perhaps it was the charger... which would be odd. now when it's plugged into the PC the amber LED comes on for a second then switches to green. i'm going to try and use it for the day and make sure i can turn it on and off without any problems. the AT&T store is closed here today so i'll have to get a charger one day during the week. i will post back at the end of the day.

Diamond wont charge with dead battery

Nightmare.
Got my Diamond today, and charged it up.
It ran out 5 minutes ago, so I plugged it into the mains charger.
It vibrates, shows HTC and then gets stuck in a constant reboot. It's like it gets a little charge, uses it, then restarts the process.
I guess the battery is so dead that even the mains charger cant give it enough boost to start charging.
Help Please
If you only got it today then id be sending it back as it seems to be a faulty unit. Perhaps someone can give you a fix but if it was me, id be demanding a new working unit...you just never know what other faults the phone might have.
Good job I didn't Hard-SPL it straight away.
Damn, Always happens to me.
Are you trying to charge it with the wallcharger or by usb to a computer.
Beacuse if you are doing it by the computer there is an option on the phone that disables charging when conected to the computer.
Good luck dude.
Definately wall charger.
I think it's f(***d
I'll go back to my Kaiser and wait for the Raphael I think.
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Tried the following:
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
Tried entering bootloader but same reset loop.
Tried hard reset, gets to grey screen with blue text but then reset loop again.
I tried leaving the battery out for half an hour and trying again but soon as usb is in it powers up and reset loop.
I put a multimeter on the battery and it is dishing out 3.7v as expected.
I think the device is knacked, even though I was using it for most of the day.
laporte said:
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Click to expand...
Click to collapse
Usually a hard reset solves everything (hopefully)
Sergio PC said:
Usually a hard reset solves everything (hopefully)
Click to expand...
Click to collapse
Tried hard reset, gets to grey screen with blue text but then reset loop again.
Nope
leave it charging for at least 10 minutes before turning it on.
bakman said:
leave it charging for at least 10 minutes before turning it on.
Click to expand...
Click to collapse
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
don't even touch the power button!
the device should not start if you touch nothing and just plug the powercable!?
i don not think that you press the powerbutton accidentally while plugging the cable, i hope i'm right?
Without touching the power button, I plug in the charger and the phone vibrates and starts.
From dead:
1. Plug in charger
2. I get 2 swirls of white on the round button thing
3. Phone vibrates
4. Smart mobility logo shows
5. Phone reboots
GOTO 1:
i miss the touch diamond screening with rom version etc.
normally it shows up before the htc smart mobility screen.
i don't think the battery is the badguy. seems more a fault in ipl or spl?
You're right.
I was wrong when I said smart mobility.
It comes up with TOUCHDiamond across the centre of the screen and right where the little red numbers USUALLY appear in the bottom right, it reboots before that.
To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and ENTER buttons, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see message on the screen
4. Release the VOLUME DOWN and ENTER buttons, then press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
save this info on your computer
Sorted!
I left the battery out overnight, and when I came to work this morning, I plugged it into the charger and it didn't automatically start up so it got a good 3/4 hour charge which then enabled me to fire it up for a full charge.
congrats! i hope for you that this problem doesn't come back!
Sounds to me like it also could have been the power button was jammed pushed in. Maybe leaving it for a while without pushing the button did the trick, allowing it to release itself.
In case that was the problem, keep an eye on the power button in case it seems to be a bit dodgy. If it is going to do it again, then you want to swap it immediately for a replacement brand new unit. After a while, if you try to swap it out, they will give you a refurbished unit, not a brand new one!
Of course it could have just been a software bug, that was cleared by letting it fully power down (as others have said).
Just make your decision quick before you end up with a refurbished model for replacement.
Just to let you all know.
Over the weekend I fully charged my Diamond, and without even making a phone call or using WiFi, Bluetooth or anything the battery lasted 1.5 hours.
It's gone back to clove now for a replacement.
I've seen a few people having this issue so I advise getting it back for replacement asap.
My diamond got very hot during normal use (without charger). Is that normal? Not the battery but the actual device.

Tytn II possibly dead HELP!!!

It looks like my Tytn II might be bricked... I have searched and searched and can not find any info on this. The phone will not turn on. I know the battery is dead, but it should have the power to try to boot. In fact, I have not used it in a while and I just tryed to boot it, it got to the starting screen, then the windows loading screen, and then I walked away for a few minutes and came back it and it was a black screen. Tried to turn on again and it did not power up. Upon plugging it into the charger, I get a solid red light on the top. When I remove the battery from the phone as the charger is connected the LED immediately changes to solid orange, and the blue led next to it comes on as well. When I disconnect the charger all the LEDs go off (obviously because theres no battery) and when i put the battery back in the phone i get a dim red light.
is the phone bricked? im thinking it might have slight water damage but it has been like 2 weeks since then so it should have dryed up i assume. tried to reset a few times with the little reset button next to the charger port, nothing. is it possible the battery may just be done for? any help or suggestions would be great. thanks.
I had that isue but i just leaved the phone on charger and everything came back to normal It's still working very well. But, i cant remember how i get into that situation but i surely know that i saw red light on top .
thanks, now that its been on the charger for a while i now get an orange LED. i will let it charge for a while and see if it awakens after almost 3 weeks of utter deadness.
Try waking it while on charge itslef.
Regards.
Carty..
Carty said:
Try waking it while on charge itslef.
Regards.
Carty..
Click to expand...
Click to collapse
just tried and it got to the very first boot screen and then went black and the orange and blue LEDs stayed on. tried to reset, no luck. unplugged charger, still LEDs stayed on. so then I took the battery out, all LEDs went out, plugged it back in and now i get the same red LED again.
update: now i get a orange LED as its plugged into the charger, but when i try to turn it on it gives the first boot screen for like 3 or 4 seconds then turns off...
I am getting exactly the same problem?
I tried to install android - got it working, came on a few times - then just totally died - It showt he HTC boot logo, but then just turns off.
Does anyone have any ideas.
does your computer see it when plugged in via usb?
perhaps this will help? http://forum.xda-developers.com/showthread.php?t=358136
oh and also you have tried to enter the bootloader mode right?
I've had this issue, millions of times. What I do when I have problems like this (and problems like when I turn it on, it says the battery is low when it isnt, and when you connect your charger/USB, it dies on you)
Try removing and putting the battery back on.
so in simple words
charge the battery first (dont bother trying to turn it on)
and then remove the charger (this plays a big role)
take out the battery, put it back in, hope it works.
The same thing just happened to me, I thought it was toast. I would get the red light when I plugged into the charger, and after a few minutes it would turn to orange. I tried to turn it on then, and it would start to boot up, then shut off a few seconds later. This happened a few times. I just left it plugged in overnight, and when I woke up it was on! Only problem I've noticed is the orange LED is always on, but I can live with that

Dead

I let my phone battery die, and now I can't turn it on.
Usually I get a red light which goes when the battery is in if its charging.
Sometimes I get a red light even when the battery is in and its charging.
If I do a soft reset, sometimes I get a flashing red light on the sides but then nothing.
I managed to get it back briefly by doing all manner of hard resets and soft resets, and taking the battery out and putting it back in over and over again for about half an hour...
Then I left it charging for half an hour or so and carelessly allowed the battery to die again because I needed to take it with me somewhere - so the same thing has happened again.
I left it charging overnight but I'm not having any luck with it this morning... any help would be much appreciated.
yeah similar problem here. my phone warned me the battery was low... i ignored the warning and used it until it died completely. then it wouldn't turn on. it was late so i just plugged it into the wall charger that came with the phone. i dont think it charged cause in the morning it was still flat. if anything i think having it connected to the charger while not charging drained the last a few drops of juice out of it. had a number of confusing red lights coming up in different spots at different times.
i read on here some guy managed to charge it by getting 3 AA batteries and connecting them directly to the battery for a couple of minuets. i did this and managed to turn the phone on! hoooray!
it had 1% and died in less than a couple of minuets even though i had it on the charger. tried the 3 AA battery trick again but to no avail. i think my battery is dead.
i'm pretty certain i will need to get a new one. i hope you are able to get yours working without buying a new battery.
im really annoyed the Sony Erricson batteries work out to be close to $100 AU. i would prefer to get a legit one... but does anyone have any experience with unofficial batteries? are they any good?
Sorry you're in the same boat... Ericsson really should have made this phone so that it can run out of battery.
Interesting - tell me more about the 3 AA battery trick!
sounds like the cells in your battery isnt balancing hence its dying...think you'll need to buy another one / or at least try another one to make sure it is and not the phone...
Hmmm... I fiddled and pressed buttons and took out the charger and put it in, and then kept pressing the on button while I was doing something else...
Suddenly it made the click noise, but it's not back yet.
It seems to have crashed on the 'Sony Ericsson' start up screen with the green logo.
I don't know if it's charging or not, so I'm not sure whether to turn it off to try again (at the risk of losing the battery), or leave it to charge as it is before I turn it off and can't start it again....
At least it's progress
There are a couple vof threads with many solutions. Look for them, they are very useful.
Yeah I've found a few - Thanks... just nothing they mentioned has worked yet
I think the problem I have may be a slightly different now anyway...
Now, if I unplug it I can't turn it on, but if it's plugged into my computer cable I can get it (every time - after about 3 minutes) to go to the Sony Ericsson loading screen but no further (as if there is no hard reset file for it to load). I can do that by plugging it in, then doing a soft reset (which produces flashing lights on the side) then holding on until it clicks (usually trying that a few times). When it clicks the lights on the side flash and it looks like it charges for a second before the lights go off and its just hte loading screen. I left it for 5 minutes and it turned off completely. Nothing happens if it's plugged into the wall cable at all.
Have you any idea how I might be able be get something to load after the loading screen?... Or any thoughts as to whether you think it's likely to be charging when its on that screen?
Thanks
Hmm... It seems you have a software problem as well.
Here is what I would do: get another battery (fully charged) and try one of these hard reset methods:
http://forum.xda-developers.com/showthread.php?t=437607
Something should work...
Sweet - I managed to get the hard reset screen to ask me the question about going back to factory defaults... after that the lights on the side are coming on to show its charging....
I guess there's a chance that when the battery is charged it'll have the juice to get past the loading screen... I hope anyway.
Wow this title gave me a heart attack almost
i thought someone is dead
plz i need help
hello good day plz i neesd to flash my htc p3600 and sony ericcson cybershot i need a software i can use to flash them plz help me any body that has an idea
just ordered a 1800mAh mugen power replacement battery. should be here in about a week my old SE k800i will be getting a bit of a work out in the mean time.
i think this break from unnecessary technology which I'm far too attached to will do me good. I'm far too materialistic.
hope you manage to get your battery going again!

won't turn on/can't select any boot options

I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.
katlic said:
I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.
Click to expand...
Click to collapse
Is it possible that the that connection between the power cord and the phone itself is loose or damaged? I'm just guessing here as I have never opened up the back of my phone.
I would check your battery terminals then leave it to charge if it does. You could also try a factory cable. Another thing would be to try fastboot while connected to your laptop and see if it stays on, and if it does, try reflashing all partitions.
Sent from my MB886 using xda premium

Categories

Resources