Related
Completely bricked my phone, does not connect to pc even from bootloader, bootloader says "usb" pc says something about a usb device malfunctioning. So I cannot loadwizard love my only input seems to be via sd slot. Can it be saved? please help!!
You should start by listing your phone model, what you were doing when your phone stopped functioning, the ROM you tried to use, whether you followed any flashing or unlocking guides, etc.
sorry all, I spent all night trying to sort this . Post a thread asking for help (always a last resort!) and sorted the problem about 20 later.
benoz said:
sorry all, I spent all night trying to sort this . Post a thread asking for help (always a last resort!) and sorted the problem about 20 later.
Click to expand...
Click to collapse
Still, it would be good to post your information and what you did to fix it. It may help a newbie in the future.
fair enough, g3 wizard running 2.8.7, went to update radio and killed it, would restart and run very slow, no usb connection etc. was running a ipl/spl 2.6.2 or similar. tried to install wizard love but got an error message about a malfunctioning usb device (something like that). Deleted activesync 4.2 and tried again, no goos but when I installed activesync 4.5 I managed to install button rom
i just spend 2 days searching for a solution, i use the search option but without results..
I got a mda g3 device ipl spl both 3.08
i flashed it with a wcrx2 rom wm6 based, but during the flash it stucked somewhere and then it went to bootloader.
If i turn it on u get the bootloader screen..
I tried several roms even the original ones, but NO CONNECTION with USB !
i get the Connection error !
is there someone who know how to solve this?
id rather paypal u 25 euros for solving my problem then send it to customer service t-mobile !
come on guys
i really need some help here !
you can still flash from bootloader mode
you can't connect via activesync but you should be able to connect still
make sure you don't have any virus protection firewall preventing the connection
then try flashing the button rom or something
ewatylerdurden said:
come on guys
i really need some help here !
Click to expand...
Click to collapse
First verify if your phone is establishing connectivity with pc through usb cable.Get into bootloaders and connect your phone with the pc via usb cable,verify if small usb appears at the bottom of the bootloader screen,if it appears then run the Ruu,if doesn't appear,then you have a either usb cable fault or mini usb port of the phone is damaged,it maybe that usb slot of the pc is not working,try with other usb input of the pc .
Cheers !
first i thank u for the time u took to help me out..
i tried several times to flash my rom and yeah i see the USB text in the corner of the screen, so im 100% sure the USB is working..
but im gonna try to flash it with the BUTTON ROM
are there other roms wich i can use for flashing my mda?
i mean wich roms are good for flashing my mda that stucked in bootloader..
cause the other ROMS didnt want to connect with my mda !
i was halfbaked when i typed this text..so sorry for my grammar et..
my computer is not reconizer this my Kaiser help me urgent
That's very little information. Has it ever worked? What have you changed recently? Does your computer even acknowledge that the device was plugged in? Is there an existing partnership?
You can try ending all partnerships between the computer and the phone. Without knowing what you've done, it's hard to give any more advice than that.
I'd also direct you to the Wiki and the Sticky...they both have lots and lots of information about the phone. I'm just assuming this has something to do with flashing a ROM on your phone because it's in the Upgrading forum and not the general Kaiser forum.
dont understand, i have windows xp and activesync dont have reconizer the kaiser!!! and dont flash the pda :S:S
Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.
Make sure you have the latest version of ActiveSync as well.
If I understand you correctly, you have not flashed your phone. Is that correct? If I am correct and you are still using the original ROM and software, then this question really belongs in the Kaiser forum and not the Kaiser Upgrading forum.
grizzley said:
Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.
Click to expand...
Click to collapse
DOnt Work!!!!!! :S flash without usb ???? how to???
x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....
sexylatin1 said:
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....
Click to expand...
Click to collapse
how to format microsd and is work in card 2GB?
x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
If this is the best you can come up with after people have tried to help then I guess you haven't read the WIKI yet.
It's obvious English isn't your first language, but if you don't read AND understand the WIKI then you will break your phone.
If necessary get a friend to help with translation. Or post your question in English and your own language - then maybe someone on the forum who speaks your language can help out.
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
edit I don't know.
obion said:
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
Click to expand...
Click to collapse
You can only change your Hardspl from your SD card. You can only initially flash Hardspl from your Pc .
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
obion said:
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
Click to expand...
Click to collapse
You are right, sorry I wasn't clear.
Very bad
you can use jump SPL and then flash hard SPL from SD
badillo said:
you can use jump SPL and then flash hard SPL from SD
Click to expand...
Click to collapse
Providing you had the foresight download and maintain jumpspl on your phone prior to your usb port breaking
but jumpspl can still be "downloaded and maintained" on the device using the mobile browser to access the internet over wifi and/or the data connection...?
so would i be correct if i summarized all the posts in this thread by concluding that a broken usb port is not a hurdle in getting hard spl on your phone?
cuz badillo says hard spl can be applied from sd...and denco7 says that jumpspl is required to get the process started...and i propose that jumpspl can be downloaded to the device by wireless means...
or is this conclusion of mine incorrect?
hmm jumpspl on a sd and copy to the fone?
i honestly think thas jumpspl, and sdcard update cant work together.
but please prove us wrong, it makes unlocking a lot more easy
i want an answer to this topic!!
I have a problem which I need to change hardspl also
thank you very much
You have to have a usb sync for first h-spl 3.29 after that you can read the instructions in h-spl breakdown by Dave Shaw in Sticky ROM dev and surely enough you can flash via SD
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
kyniemxotxa98 said:
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
Click to expand...
Click to collapse
Look HERE
JumpSPL
7Zip to extract zip files attached bellow! Best of luck to you!
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
Bottom line is , you can only upgrade your hardspl via SD Card, you can only hardspl from stock spl via usb connection.
Believe me a lot of smart people have tried for a while.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
You are in the KAISER Forum! You need to be asking this in the Diamond Forum! I only gave you that info assuming you were a Kaiser user! Anything Kaiser will only brick your device for sure!!!!!!!!!
Update your signature to what your device credentials are so people are able to help you better! Take mine and Denco7's for example. If more people had their signatures setup, it would make it so much easier to give out advice!
EDIT: If usb is broken how are you charging the device?
The Diamond does not require the launch of a jump spl, the hardspl package by olinex has all the required files in it. But it must be run from the PC which requires an active sync connection
And Diamond user stop double posting, go to Diamond section and do your research........
Denco7 has answered you in 2 threads yet you still coming back to Kaiser section...
hey guys, I'm a newbie and I have a problem that really irritates me, I have bought an old X1 running windows mobile 6.1 German, I wish to install an English or a French OS, the problem is that my USB cable just don't work, I've tried several others on many pcs, still having the same problem, isn't there a way to install HardSPL without using the USB cable? another question; is it really necessary to install HardSPL if I want to install an original SonyEricsson's ROM, please answer me, I just don't understand a word of german language, thank you, please.
u dont have to hardspl if using original rom. but u still need a working usb cable. how can u install without a cable? OTA?
i was thinking of the memory card method.
Why not using USB Cable, though the fake one is not expensive.
You can also salvage from your other gadget, mine Ext. HDD
Do u insist using Storage Card?
Okay, I'm not sure if it will work or might destroy your X1.
When you doubled click (Execute) the HardSPL you'll found "RUU_Signed.nbh" extracted. Maybe you can place that "RUU_Signed.nbh" to Storage card. And then execute bootloader, like flashing ROM.
*Notice* It's only my idea. I have no guarantee about this because I've never done this.
Maybe you can PM the expert (the creator of that HardSPL) first.
U just get an error when installing hardSPL?? I think your computer USB got a missunderstanding or uncompitibility with another USB driver, maybe u should to install a new fresh computer with USB 2 installed, then try this to hardSPL your X1, worked on me, hehehe
DO NOT try and install hard=spl via sd card
it WILL fail and you could breaak your phone blah blah!
just buy a cheapo usb cable
have you installed activesync or WMDC first??
well, i've solved my problem guys, thanks. I've just bought a fake usb cable.