guys I have problem with my phone's screen, the upper part of the screen during portrait mode is no longer responding to the right spot. but the rest its ok...anyhelp?do I have to change my LCD? I even had it hard reset which gives me a bigger problem, a Align Screen menu pops out and I could not align it....anyhelp????
looks like you have defective digitizer screen, try to take apart and reseat the LCD connector. maybe it'll help.
last resort, change the digitizer screen.
yes, I think that's the same problem that i've been facing since last year :-|
any I dea how could that be happens ?
or is there any way to do it without bricking the device ?
welll....
I am looking at the possibility that it needs to be stripped down and cleaned! dirt could be causing the issue around the edges by applying pressure to the digitizer!!
does anyone know of any toolkits you can get to take this thing apart I am not too confident with my kitchen knife and chisel....
Probably on this forum somewhere...
(edit : I just did a bit of pushing down and hooking a piece of card around the edges of the screen and it seems to be working fine however this can be temporary...)
There are guides in this forum to taking an Alpine to pieces completely: I had to change my screen recently and it can easily be done before the backup battery has run out of juice.
If the digitiser part is behaving erratically you cna just purchase a new digitiser for about £4.95 off ebay, rather than fork out around 30-40 for a new screen.
TOols you'll need are small screwdrivers and a small set of torx screwdrivers.. again a search will tell you what size (I have a pack of t5 6 and 7 and cant remember which it is - it's the same pack you buy for disassembling mobiles)
Joe
ok my kaiser, tilt, 8925, whatever, whatever, has a loose slider. if i press on the screen you can feel the upper part of the phone move. Their is a noticable gap between the keyboard and the upper part of the phone. My brother has a titl and i compared it. Is their any way to tighten or fix the problem
bump.
I'm comfortable with taking my phone apart and putting it back together.
s0nnyyyy said:
ok my kaiser, tilt, 8925, whatever, whatever, has a loose slider. if i press on the screen you can feel the upper part of the phone move. Their is a noticable gap between the keyboard and the upper part of the phone. My brother has a titl and i compared it. Is their any way to tighten or fix the problem
Click to expand...
Click to collapse
Does the screen feel loose when the device is closed? Or do you mean its loose when its open? Mine was loose when it was closed and almost made a creaking sound when I applied pressure to the bottom right corner, I removed the screws, but was unsure how to disassemble the unit (at the time), so I gave it a good dusting, replaced the screws and It's fine now. What my little dusting solved is still a mystery to me, but it worked.
I'm after sitting sleeping on my Diamond. Took a nap on the couch, woke up and found my diamonds screen unresponsive. Now I'm not sure if I've broken just the digitizer or the LCD too.
Basically - when you look at the screen, there's an edge of about 3/4 of a centimetre around the outside of the screen that's okay. But a large rectangular shape on the inside that's all multi coloured - like spilled oil. I'm thinking this because i've broken the LCD but I see no cracks. Inside this rectangle is a pattern of dots - evenly spaced colums and rows, but only where I can see the colour.
I've only had this thing a month Please don't tell me I need to go spend €60 on ebay to replace the LCD and Digitizer
I'll try and take pictures tonight.
http://forum.xda-developers.com/showthread.php?t=432559
Well I guess My poor diamond is also down for the count the touch screen is not responsive at all I tried a soft reset so many times I removed the battery and then put it back and still the touch screen is not responsive.... Oh boy wht a day today and craped up luck too I went to the service center and they said they will need to chk and get back after 3 days wht a bummer anyway I'll need to backup all my contacts thru this software MyMobiler which can access my mobile from the computer then I can back up everything and I'll get my old trusty HTC Touch out now and start using it....
Has anyone mounted a new digitizer screen on an diamond?
my digitizer is cracked and a newone cost about 20 euro better than a complete lcd with digitizer for 45 euro
but i cant find anywhere pictures or information about this.
i swaped quite a fiew digitizers in the past, p3300 and touch and the good old 9100
but this is something else
i change a housing of my kaiser everything look good but i found a problem my sliding switch don't work any more my phone don't power on when i open a slide and don't go to landscape mod
i opened again i found 4 metal pins on every corner of sliding mechanizm i think some of connections to those pins are lost i try to pull up that pins and after that same thing i don't know how those work when i close phone then have contact and when you slide they lose contact with metal i think that is good and that works like that or they don't have contact until sliding mechanizm create it
anyone have this problem i don't know how to calibrate that pins
and
every time device i start device is in landscape mod
Hi
Take a very good look at the casing you have removed. The rotation sensor operates by magnet and often this is located on the casing. The magnet needs to be moved from the pld casing to the new one.
I don't have pictures of the Kaiser handy just now, but look here and you'll get the idea - these pics from the Hermes (TyTn):
http://forum.xda-developers.com/showthread.php?p=2686388
Mike
OLEEEE
thank you man you are genius
i found little round magnet on the back plastick of the screen it is soo tiny
thank you again
regards
hi,
my touch diamond 2's touch screen stop working randomly ( i think that i applied too much pressure on 1 spot for too long). I can see the touch screen dots on the area. I am just wondering if I were to repair this, would i be replacing the DIGITIZER or the TOUCH SCREEN.
Thank you soo much
warranty might cover that. It might not be your fault
I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?
jasonngu1991 said:
I have decided to fix the part myself since I do not wish to ship the part to their location in the US. Any idea if its the digitizer or the LCD screen that i should be replacing?
Click to expand...
Click to collapse
Search the Wiki, there are dismantle instructions.
I had the same on my display, and was able to move the dark spot to the edges where it disappeared.
I moved it with scratching it with my nail very gently applying some pressure.
In Europe HTC offers a pickup and return warranty, is that different in the US? If it is the same I would send it in to HTC for replacement, since it might happen again pretty soon....
I already have 3 screens replaced :-(
jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..
mercurialcc said:
jason, did u manage to fix this? i have the exact same problem and pushing the "bubbles" towards the edge of the screen didn't help. my screen is still unresponsive..
Click to expand...
Click to collapse
Try applying duct tape to it repeatedly until you get it back.
Yes, both
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...
maybe you should reset it
Working Solution Till Now
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Solution
Okay, I've just had this problem with an HTC Touch, and I think this works with any HTC that has a "digitizer" rather than an all-in-one touchscreen (I think newer phones have digitisers).
I'm not sure if this will always work, but I've just done it - sometimes the inactive touch screen is "broken" because the layers are stuck together (so the phone can't tell where the touch is, hence unresponsive). With mine, I looked at the screen side on and could see a kind of "oily" patch in the light.
The solution is to get masking/gaffa tape - the very sticky brown one. Stick it down on the screen/digitizer and then keep pulling it off - this pulls the layers from each other. I kept repeating this lots before it worked - and in the end I pulled the top layer completely off (I think you should pull from the top of the phone, as the layers need to be attached at the bottom of the screen/digitizer). Once it pulled away, I gently lay it back down (after panicking!!) and hey presto it started working again.
Good luck!
Digitizer replaced but still not working
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance
Replace the Touch Diamond2 Digitizer touch screen.
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.
prabhat said:
Hello Friends,
I have TD2 mobile and today I had same issue. I was thinking it was because of the weather or some.
I remember it did happend several time before, but when I restart the device several time it does work. So I was ignoring.... But today it did not work.. looks like going toward end... So I did soft and hard reset without and that did not helped me.
So I switched off the mobile, "heated" the touch screen gently with my hand for 1 min and started the mobile again and it worked for me .
Not sure if this is a solution, but will work.
May be I will contact Service Center here in Hyderbad and see what is wrong here?
Hope this will help you all...
Thanks.
Click to expand...
Click to collapse
i tried this and worked for me .
i removed the screen protector and switched off the mobile and heated the screen with my thumb and it worked again
thank you prabhat
and i'm using Topaz touch diamond 2
with photon ROM 1.6
Shoofty said:
I recently replaced the digitizer (touch screen) on my HTC Touch Diamond2. Since I found on the net, no instructions for replacing the actual digitizer, I thought I might include some here.
It was relatively easy to fit. The only difficulty I encountered was a lack of information about how to actually remove the old one. The various instruction sets found on the web all stop once the screen is removed. But the digitizer is not covered by these instructions. The digitizer is bonded to a thin glass immediately under your screen protector (if you have one fitted) and after the screen is removed following instructions you will find on the net, the digitizer and the thin glass sheet that it is bonded to must be prized off from the front of the housing. The digitizer separates from the glass easily, but the glass is securely bonded to the housing with a silicon glue. It must be prized off by gently lifting a corner and applying a little upward pressure allowing the glue to slowly and gently let go. Don't be surprised if the glass breaks during the process. Once off it is a simple matter to press the new one in place. Just remember to start by slipping the connector bus (cable) through the narrow slot between the metal outer housing and the inner components. I used a set of tweezers to poke it through. DO IT FIRST before pressing the digitizer into place.
Okay, as I said the process was easy and took about 15 minutes all up.
Click to expand...
Click to collapse
Thanks for the heads up on the glass part mate. Just replaced my TD2 digitizer too. Kinda freaked out at first when the glass split.. haha
Anyway, just wanna 1 more info. When removing the old digitizer, it'll be easier if the front housing was heated first (with a hairdryer on full or a heatgun) to soften the glue. It'll be easier to remove afterwards.
Word of warning though. Only head the housing when REMOVING the old digitizer, DO NOT use this method when applying the new one. The digitizer dies because of heat. Heat is what causes the newton rings issue.
Shoofty said:
The touch screen on my Touch Diamond2 stopped responding to my touch (or the stylus) and I tried everything including removing and replacing the digitizer bus just in case the connection was the issue. But all to no avail. Finally I decided to replace the digitizer (touch screen)
The problem for me is that it made no difference. The new digitizer doesn't respond to my touch either. The problem is apparently somewhere else.
If anyone has encountered this problem and has a solution I would be grateful to know what it is.
Thanks in advance
Click to expand...
Click to collapse
I have the same problema with my Diamond2. I have also changed the digitalizer with no success It is still not responding to any kind of touch.
Shoofty, did you manage to fix yours?
Thanks in advance,
Javier
Fixing TD2 touch screen
TD2 touch screen is a common problem I guess.
Symptoms are :
1- Touch screen does not respond sometimes
2- You can see a grease like layer under the touch screen
3- Sometimes if you look closer to the screen at some part you can see a a liquidized small area.
Solutions:
1- If you see the liquidized dot on the screen turn off the display and try to rub it with your finger until it disappears. turn it on again and try if it works. I guess heating with the finger as other peeople here suggest does the same thing. However this is a temporary solution. Your touchscreen will die at some date. I used my TD2 for 8-9 months using this method. But at the end touchscreen died.
2- Replace the digitzer or complete frontcover. Actually this might be easier than you think. I replaced mine in half an hour. I bought a front cover which includes the digitzer (http://www.ebay.de/itm/Original-HTC...zer_Ersatzteile_Werkzeuge&hash=item4cfe6f78dc) and openning tools from ebay. Dimanıond 2 disassemble and assemble videos on youtube were very helpful. I strongly suggest to buy the complete frontcover (inc digitzer). It makes replace process much easier and gives the device a brand new look. My old front cover was worn from the corners (which is also very commpn problem of TD2). Now it looks brand new. No strach on the display and body.
Thnks Ozkarah.
I happened to realize that, surprisingly, the touch screen of my HD2 started working if I heated it up with a hairdryer. So, I think something else is wrong beyond the touch screen, probably the connector to the main board of the mobile. It might expand once it is hot and that is why it starts working. In any case, I think that is beyond repair
HTC screen calibration
2Fresh said:
I recently replaced the Touch Screen on my Diamond 2. Same problem; spots that "stick" in the middle. I used to solve this by running both my thumbs down the sides of the screen to "puff up" the low areas in the middle.
The part you want is actually called a "Digitizer Touch Screen" on eBay, cheap too. Prepare to spend about 2 hours fiddling with very tiny screws, connections and glue to tackle the job.
The hardest part for me was actually getting the Touch Screen to work; it seemed to be calibrated in mirror-image AND turned 90 degrees sideways, which made getting to the calibration functionality an extremely frustrating experience. I spend another 3 hours on that, but now I've got a perfect phone again, since I ordered a new case as well. No use taking the entire phone apart and then rebuilding with a molested outer shell...
Click to expand...
Click to collapse
Hi,
I have same problem when I changed new screen (screen is calibrated in mirror-image AND turned 90 degrees sideways).
Could tell step by step how you get your screen calibrated?
Thanks