Battery or Charge / charging LED no turn to Green problem - Touch 3G ROM Development

have every one this problem ?
I have seen this bugfix at the HTC-Support-side for the Diamond2 :
"Update for HTC Diamond2 Power LED Notification"
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
"This update for the HTC Diamond2 allows you to see the battery charging status right from the LED. Now enhanced to illuminate green when fully charged, with a quick look you will know when your phone is powered and ready to go.
Installation Instructions:
Note: This Update only can be applied for ROM version between 1.36.XXX.X to 1.44.XXX.X and 1.66.XXX.X to 1.76.XXX.X "
-------------------------------------------------------------------------------------------------------------------------------------------------------
at my Jade I use the newest official ROM from HTC "2.32.407.2" with radio 41.30.12
i don´t have to try install this bugfix at my Jade, i think don´t works if my Rom version is over this is described for the Diamond2 .
I´ve read here from many users there have a problem with charging the Jade, some different solutions but nothing is a really correct solution to solve this problem.
the different solutions I´ve read is:
a. charge with power on and turn the backlight off (nothing turn to standby)
b. turn the Jade complete POWER OFF not in standby (this works at my Jade)
c. install a third party software for the Icons at the top (especially for the Battery Icon).
d. but the best (ironic) and the coolest solution comes from the HTC support, there I´ve send a mail with a discribe from this problem:
"please call ARVATO-Support to send the Device for Repair" ---- i think the guys from this HTC Support have anyplace in Germany a "one EURO Job" .....
what would this Guys at ARVATO to do with the JADE, they are Sorcerers or have a Cristal-Orb there can see the answere ?
have everyone here another solution ?

Wrong section. Should have been posted under "Jade/Jade".

Hi,
Have you installed any third party software that display a battery icon? If so, that would be the problem. Try to uninstall the third party software and do a soft reset, then try to charge the battery. Thanks.

No, I don´t use 3rdParty Software for the Icons at the Top of the Screen, I use SPB Mobile Shell where I generally don´t see the icons.
I think it´s a bug in the Rom or Radio, it´s the same failure at the Diamond2 and for that Device give it a Bugfix from HTC.

hi
1. if u are using any cooked rom like the Pdaviet rom yes this will happen
2.if ur using only the original rom no this should not happen
u can try doing a hare reset how to do it clik last line of my sign iv explained the same their but remember to backup ur phone as u will lose all data on ur phone when u do it OK
Chris1507 said:
No, I don´t use 3rdParty Software for the Icons at the Top of the Screen, I use SPB Mobile Shell where I generally don´t see the icons.
I think it´s a bug in the Rom or Radio, it´s the same failure at the Diamond2 and for that Device give it a Bugfix from HTC.
Click to expand...
Click to collapse

you read this at my first POST "at my Jade are the newest official ROM from HTC "2.32.407.2" with radio 41.30.12"
this Rom is not from Pdaviet.
after a full new Official Rom upgrade I´ve made, it is a hard reset normal.

I have the same problem.
At my Jade I use the official ROM from HTC "2.32.401.2" with radio 41.30.12. Anybody know the solution for this problem?

I think the Problem is..... "battdrvr.dll"
if everywhere have a JADE with a earlyer ROM where the charging works, can this "battdrvr.dll" copy and upload here.
this .dll was locate ind the Windows directory.
then we can try to change with the current battdrvr.dll
I´ve see it give a "XDADev_BatFix.CAB" , but this works perfect with the HTC Prophet with the same problem.
hmmmm, I don´t want to try this bugfix, i think this brik eventually the Jade...
It seems that HTC have generally a problem with many Devices with the Powermanagement.

I find if I restart my Jade, battery indicator shows me real battery charging status.

Same here! Restart and all's OK. Running stock firmware, newest update from HTC.

Related

Flashing to new rom

I'm sorry for this post, because the answer is probelly somewhere on this forum. But I can't find it.
I have my diamond for about a year now and I like to install a custom rom with windows mobile 6.5. But I can't seem to figure out what I need for this.
I already chosen a rom, but I have no idea if it is any good, because there are so many roms out.
http://forum.xda-developers.com/showthread.php?t=563245
So my first question, is this rom any good?
Second question, what type of hard SPL do I need, Do I need the normal one that requires roms to be signed or do I need the developers edition?
Third question. Do I need MTTY for this or can I first try it without MTTY?
And the last question, if I don´t like the rom is it easy to install the original rom again or do I need to do something special for that.
I hope you guys can answer my questions so I can start flashing my rom.
Grtz, Eric
EDIT: I tried installing hard-SPL unsigned, but get an error that it can't connected to my phone. But it is connected using windows mobile device center
why do you want to flash a new rom?
ive recenetly done the same, i wanted to flash my rom as the original was tied to vodafone and some of the features like youtube, facebook, and opera wouldnt work as they wanted vodafone connection ( im on virgin mobile).
anyway after much trial and error i in the end found it versy easy.
3 simple steps. first flash your bootloader
i found the best and easiest one was spl olinex version 4.0
u need to softboot to do this ( hold the down volume and switch on phone, have usb cable connected then use the flash util provided with the above.
once thats done you need to flash rom the radio
again the one out there that seems the best to use is version 1.00.25.05 diamondruu radio
again soft reset so you get the try colour screen and run the flash rom update ( takes about 2 mins at most)
finally choose your version of win mobile 6.5 ( i got windows revoluton 7.1 ultra clean edition)
do soft reset again, then run the flash update and again this takes about 5-10 mins for this)
all worked perfectly for me and it was my first try.
though i will be changing it as the revolution is missing some vital aspects i like.
i know its basic but hopeully you can see its not the daunting prospect some people make out though any rom upgrade carries a minot risk i found this to be as easy as 1,2,3
good luck
cloudedhopes said:
why do you want to flash a new rom?
Click to expand...
Click to collapse
Because I would like some new features on my phone. Like wm 6.5 or a new version of manilla. It's getting a little boring having the same phone for over a year.
@miramele, thanks for your response. I'll give it a try tomorrow and hope I won't brick my phone.
let us know how you get on, it took me several attempts as each time i was trying while within the phone itself, if you hold the down volume key and power on the phone you get the tri colour screen, in this mode i had 100% success each time.
doing it within the OS with phone on it just stuck at 0%.
And since then i have re flashed it with a diff version of wm 6.5 that i prefer and all is good.
the version i flashed to is the manila 2.1 with the latest touchFLO 3d so ive not even bothered with Spb mobile shell though may add this later.
miramele said:
let us know how you get on, it took me several attempts as each time i was trying while within the phone itself, if you hold the down volume key and power on the phone you get the tri colour screen, in this mode i had 100% success each time.
doing it within the OS with phone on it just stuck at 0%.
And since then i have re flashed it with a diff version of wm 6.5 that i prefer and all is good.
the version i flashed to is the manila 2.1 with the latest touchFLO 3d so ive not even bothered with Spb mobile shell though may add this later.
Click to expand...
Click to collapse
Thanks for the advice, if I understand correctly I have to get to the tri-color screen and then install hard-spl? But can I connect to my laptop while in this mode?
I'm gone try it tomorrow because I didn't have any time today.
Thanks for all the help, especially miramele.
I made the step and am now running a custom rom without any issues. Many thanks for the help and for pulling me over the line.

Unable to Load Bootloader

I have tried hitting record + power + reset and still no dice.
I did this last Jan to my BA with few problems, put in the wm6.1
Wanting to install this one WM6.5
I also installed the Wizard Service Tool and it doesnt seem to work. It will give me info but the hard reset and other rom features don't want to work.
is there a workaround for gettin to the bootloader? Or should I take this all as a sign not to brik my phone? ;D
thanks,
chela
hi , i'm new on the forum...i think i've the same problem, on my PDA2K..
I try to install a new rom from wm2003se, using a file called "preparazione BA"( i think i've unlocked the extrom), then i normally setup with the MaUpgradeUt_noID.exe..But now, when the upgrading is completed to wm6, i'm not able to load the bootoption..i can see 4 colour bands (green blue red white) but no option to boot. The rec+photo+reset seem not to work.
Could anyone help me\us??
Regards at all
Davide
after 2 hours..here are some news: my pda2k display became with the 4 color but there was writen something about R none, G none and (version onf the rom i tryed to install) then pressing rec+cam i saw for little fraction of second the menu enable kitl ,clean registry, etc.. and then suddenly the wm6 starts. After installing the OS ask me to reset..Well, it return to the same 4 color, and the only word i see is R1.11.00
I'm getting crazy...
Please big chef tony help me!
i don't know what to do now...i'm little down
Davide
...lol maybe because I dont do this often enough, but this case was solved with a little bit of RTFM!
I didnt realize I was pressing the wrong fsking button! derr!
Here is Chef Tony's post...should carve it into my desk!
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
i've solved my problem..reading on other forums, they suggest to install a rom WM5, where there was radio upgrade too..After i was able to install WM6.1 ! Now..i have to wait..and crossing my fingers!
Thank you all, if anybody has question ask me, i'll happy to help you
Bye
Davide
Davidenji said:
Hello, my ppc always dispays the four band with R1.11.00 written..After a lot of reset(often unplugging battery) and photo+rec, i was rarely able to display the boot option, but here is strange what is written(attached photo n°2): R None, G None, D 1.21 Michy.. Then pushing "mail" the OS start installing wm6, then, it ask me to boot so i would be able executing extrom to install cab file.It resets and then it appears the famous four band with R1.11.00
Any idea??
I've finished mine....Aww!!
Regards
Davide
P.s. think it's important: my bootloader is v 2.08
Click to expand...
Click to collapse
Nothing strange about what is in photo #2! That is the debugger screen.
Looks like you got it rolled back to the original ROM but if you decide to put the latest stable ROM 6.5 on there you're going to have to follow the Chef's directions in the above supplied link.
Good luck,
Chela
glad you found it out, you are right, there was something wrong with the radio, which is why in screenshot #1 there is only the radio listed and i think that's also why in #4 the comm icons are red, i've never seen that before, but could also be a custom skin in that rom.
brujeria is right, there is nothing wrong with the 2nd and 3rd screenshot, except for the 2nd one only showing the rom and no radio or protocol, meaning that the device was probably resetted by pulling out the battery and not pushing the reset pin with the stylus, unless that was also a radio issue.
unless you already started customizing your device you should probably think about hard resetting it once again and trying if that works, or even re-flash the rom, without flashing the radio, that way you'd know for sure, if from now on you'll always have to flash a "baked rom" (usually a term for a cooked rom, together with radio and extrom, a full flash, in this case i mean rom and radio rom, since the extrom is not really flashed anymore).
with best regards,
Chef_Tony
i've already customized...a little! Now, everytime i soft reset i read this: R 1.15.00 , G 1337.45 , D 1.21 michy.
I've no problem at moment..but i hope i won't never hard reset!
This Rom (WM6.1 included only Rom upgrade) it's nice, but i'm interested about WM6.5..anyway i think to keep this one untill a problem will come out
P.s. Like you say, now the antenna isn't red anymore..it's bright green
Thank you a lot for the support guys!

blac100 touch screen doesnt repond at start up confiruration

Hi every body
the Problem is i did already post the problem of the green display now i solved it by flashing with USPL GUI v 2.5.zip then updating the rom again in french with HTC FRA 1.56.406.....
now at start up phone requir as usual touch screen configuration of the stylet
the phone doesnt really repond or react on time as if i didnt tick
when i put the battery the phone starts up no way to shut down and to make a hard reset
the question is there any way or solution to fix the problem with the touch screen ?
did i miss a step after flashing with rom 1.56 ?(it was the same version in german and i changed it in french )
manouba said:
Hi every body
the Problem is i did already post the problem of the green display now i solved it by flashing with USPL GUI v 2.5.zip then updating the rom again in french with HTC FRA 1.56.406.....
now at start up phone requir as usual touch screen configuration of the stylet
the phone doesnt really repond or react on time as if i didnt tick
when i put the battery the phone starts up no way to shut down and to make a hard reset
the question is there any way or solution to fix the problem with the touch screen ?
did i miss a step after flashing with rom 1.56 ?(it was the same version in german and i changed it in french )
Click to expand...
Click to collapse
Plenty of threads already about screen alignment and no responsiveness etc like these:
http://forum.xda-developers.com/showthread.php?t=557096&highlight=align
http://forum.xda-developers.com/showthread.php?t=587931&highlight=align (try alternative solution to bypass alignment screen)
Suggest you try reading these first, search and if still not working post in one of the existing threads
Thread closed

T5355 stuck on "TOUCH Diamond2" screen

Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?

[Q] How to "virginize" HTC Touch HD?

Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!
Sopis said:
Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!
Click to expand...
Click to collapse
Dear friend,
first let's know what ROM have you installed on your device? I'm sure the problems that you've mentioned are not hardware problems, and in fact they are related to the ROM, since I have the same problem sometimes with some ROMs and some application. I had problem with alarm clock several times, just after flashing Energy ROMs! I reported this matter, but nobody paid attention, so I downgrade my device to kwbr WM6.1+sense2.1, now I have no problem with alarm clock.
about the another problem, I still have this problem, but I think it is related to WKTask! sometimes when I turn my device off by WKTask shortcut, I encounter the problem that you pointed, but it's not the case if I turn it off by hardware key.
Same question
I have used HSPL
and have tried several roms
Few days back my touchscreen stops responding.
flashed differnet roms but no difference. so i think its a hardware problem
(kinda works sometimes so may be just a loose link)
I want to send it for repair under warranty.. so can someone tell me how to get back to factory settings of Touch HD (German)
Prajwal
Ah, now we have 2 different cases.
1. Flash with USPL
2. Flash with HSPL
I'm almost sure that "virginizing" is described on HD Wiki, but nevermind...
Case 1. is nice and easy...
Go to HTC site and try to find update for your device. Before that, write serial and IMEI (not sure which one is needed, both are under the battery).
If there is "No suitable update", then you are in big trouble... try to find what was original ROM which was on device when it was delivered.
Case 2. is bit difficult... you HAVE TO remove HSPL and restore original SPL, then proceed as described in case 1. I think for german ROM was SPL 1.54
However, I have bought my device recently (with German ROM), but maybe earlier devices had some other SPL...
Check HD Wiki anyway...
prajbio said:
I have used HSPL
Click to expand...
Click to collapse
Ah... [TUT] Dummies guide: flashing 1.56+ roms [v 2.0] - [HSPL][USPL] has at least one important thing for you: stock SPL...
Thanks Guys...
I didnt think of checking the wiki...
Ill go there, and also do what you suggest...
I guess the issue is not related..I flashed a new ROM from different cook and it happened.
Nevermind...I will virginize and then have it fixed or replaced...
THANKS!!
Bodisson said:
Ah, now we have 2 different cases.
1. Flash with USPL
2. Flash with HSPL
I'm almost sure that "virginizing" is described on HD Wiki, but nevermind...
Case 1. is nice and easy...
Go to HTC site and try to find update for your device. Before that, write serial and IMEI (not sure which one is needed, both are under the battery).
If there is "No suitable update", then you are in big trouble... try to find what was original ROM which was on device when it was delivered.
Case 2. is bit difficult... you HAVE TO remove HSPL and restore original SPL, then proceed as described in case 1. I think for german ROM was SPL 1.54
However, I have bought my device recently (with German ROM), but maybe earlier devices had some other SPL...
Check HD Wiki anyway...
Click to expand...
Click to collapse
From my experience, HTC is usually ok as long as the SPL is an official one. No matter the one came with your phone or other older/newer version.
Sopis said:
Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!
Click to expand...
Click to collapse
since you just use USPL, you just need download the official ROM from HTC page by inserting your HD serial number under ROM download. then flashed it. it think this step will solve your warranty issue.

Categories

Resources