plz help td2 stopped working after flashing atempt - Touch Diamond2, Pure Q&A, Help & Troubleshooting

tried to flash my TD2 to |T|6.5.1|ROM|WWE| ★ EnergyROM "Leo" 23081/21864 | Oct 28 | ★ Manila 2.5 ★ http://forum.xda-developers.com/showthread.php?t=562942
but after it was done it just stops at the touch diamond 2 logo i tried hard reset didnt work and i tried to flash with other ROMs but it just stays at 0 % dosnt go any further what can i do cant use it at all now.
i been running with custom ROMs before with no probs.

What spl version do u have?

Spl1.33.0000

you have made a mistake. you are not suppose to flash your phone without Hard spl. Do you know where your device is originally from? if you do go to the HTC website and download the stock rom.
step 2 download the rom that is for your phone.
step 3 put your device into tricolor mode (boot loader) if you dont know how then just hold the low volume botton and press power until your device enters the tri color mode.
step 4. once you are in the tricolor mode then plug in your data cable and wait until your computer recognizes it
step 5. run the original rom that you downloaded from htc.
now your device should be flashing the stock rom and after its done your device should be able to start.
your lucky that u didnt brick your phone.
if you have any other Q's let me know

I believe most of the newer roms require Hspl v1.83 to flash. Try that

danishnicooo said:
Spl1.33.0000
Click to expand...
Click to collapse
u need Hspl v1.83, then u'll be able to flash wm 6.5 rom; otherwise u'll get stuck at 18% everytime u try to flash it

Related

How to upgrade from Orange ROM ??

Bought my HD a month or so back, it's an Orange HD and has the factory Orange ROM. Can ANYONE please direct me on HOW to upgrade to the latest Original ROM , OR one of the cooked ones, as I have no idea how to, don't wanna brick my phone.
I had an HTC Advantage before this and sold it to buy this, upgraded that with cooked roms, I need directions on how to upgrade SPL to 1.56 or above and upgrade ROM likewise. Help will be much obliged.
Crackwhore wrote a guide for this, at top of forum
http://forum.xda-developers.com/showthread.php?t=505377
I used Crackwhore's guide too for my Orange HD and it worked perfectly with HSPLWrapper_Blackstone_156OliNex.zip allowing me to flash Duttys ROM which is excellent.
I even followed his instructions to roll back the SPL to test incase I ever needed to get the phone fixed under warranty, and it worked.
Flashing Orange Touch HD
bilalperwaiz said:
Bought my HD a month or so back, it's an Orange HD and has the factory Orange ROM. Can ANYONE please direct me on HOW to upgrade to the latest Original ROM , OR one of the cooked ones, as I have no idea how to, don't wanna brick my phone.
I had an HTC Advantage before this and sold it to buy this, upgraded that with cooked roms, I need directions on how to upgrade SPL to 1.56 or above and upgrade ROM likewise. Help will be much obliged.
Click to expand...
Click to collapse
hey I have Touch HD of orange n right now im using Duty’s v3.9XT n its SUPERB on it.... I can simplify the procedure for u.it will be for both official rom upgrade and for putting any cooked rom without bricking ur phone... first ill write it down in outlines n than write the detail u need as being owner of orange touch hd device....
here is wht ul have to do.
1. Download relevant stuff.
2. install relevant drivers and USPL software on your pc
3. update your current orange rom to official updated rom.
4. Download and install any cooked rom.
here are the details....
Orange shipped touch hd's have SPL ver1.14000 in them. SPL is the bootloader. our first task is to update the SPL from 1.14 to 1.54.... if u dont do this and directly install any cooked rom. the screen colors all mess up.....
Firstly Download these….
You gotta have the updated USB sync drivers.tht can be done from crackwhores guide.
http://forum.xda-developers.com/showthread.php?t=524619
follow it. According to the operating system you have.
When you are done installing the drivers. Restart ur pc n (incase of vista: press F8 before windows starts n from menu select disable signature reinforcement) everytime u plan to flash a new rom u gotta restart n disable the driver signature reinforcement if u had a normal reset earlier as vista on normal boot blocks these drivers.
After u have the drivers installed and working go to this link another crackwhores guide n
http://forum.xda-developers.com/showthread.php?t=505377
Download these 2 files “USPL GUI v 2.5.zip” “BlackstoneRUUWrapper.zip”
when you extract file USPL GUI v 2.5.zip your antivirus gives warning tht it is virus… its not… ignore that.
Now u have to download and install the official latest rom which works with touch HD (orange)to update your SPL to 1.54 .
go to this link
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
and from here download this file.
• RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
(note this rom is specific to UK devices n only this will work on orange hd…. If u download any other it will fail)
After you have downloaded and extracted the rom file. It will be named ruusigned.nbh make a new folder and in tht folder put this file and also extract that “blackstoneRUUwrapper” into it.
Now ur ready to start flashing process… for detail check the crackwhores guide to flashing. Im just writing short outline. Make sure you have at least 50% charge.
1.First turn off ur cell.
2.Hold down volume down button n press power button till u see a 3 colored screen with SPL 1.14000 n on bottom of screen there is “Serial”
3. Now connect your device to pc via usb cable. Serial will change to usb in couple of seconds.
4.Now run USPl.exe from tht USPL GUI v2.5 tht u had extracted earlier. A window will open. On tht click “RUN USPL” n in 5 to 10 secs it will run and show u message in end tht USPL loaded and happy flashing.
5.Ur cell screen will reload n now it will show “USPL1.54000” instead of “SPL 1.14000” and usb will disappear from bottom of screen. Just unplug the usb n replug USB will come up again.
6.Now go to tht folder with Blackstone RUUwrapper and RUUsingned.nbh file
7.Run tht BlackstoneRUUwrapper.exe
8.Follow the application by clicking next n checking boxes where ever needed.
9.At end it will start flashing ur rom. It takes 10 mins.
10.When finished your device will automatically restart.
11.While its doin tht unplug the usb. Remove the back cover n yank out the battery.
12.After 5 secs reinsert the battery n put on the cover
13.Now press n hold both up n down volume buttons n press the power button once.(but keep holding the volume buttons)
14.After 3 secs bootloader like screen will come up saying press vol up to restore factory settings.
15.Do tht
16.Whe finished it will say press vol up again to boot.
17.Do tht.
18.N ur done =) if u just wanted to get the latest official rom and this has updated your SPL to 1.54000 from 1.14000.
19.But if u want any cooked rom u can easily install tht following the same steps from 1. Using the cooked “RUUsigned.nbh” and u wont end up with any problems with screen colors with cooked roms….
Happy FLASHING
Thats really great, thanks for the help guys.
By the way im a noob, what does SPL stand for
digo21 said:
Thats really great, thanks for the help guys.
By the way im a noob, what does SPL stand for
Click to expand...
Click to collapse
spl is similar to the bios of ur pc...
hispeedworm said:
hey I have Touch HD of orange n right now im using Duty’s v3.9XT n its SUPERB on it.... I can simplify the procedure for u.it will be for both official rom upgrade and for putting any cooked rom without bricking ur phone... first ill write it down in outlines n than write the detail u need as being owner of orange touch hd device....
here is wht ul have to do.
1. Download relevant stuff.
2. install relevant drivers and USPL software on your pc
3. update your current orange rom to official updated rom.
4. Download and install any cooked rom.
here are the details....
Orange shipped touch hd's have SPL ver1.14000 in them. SPL is the bootloader. our first task is to update the SPL from 1.14 to 1.54.... if u dont do this and directly install any cooked rom. the screen colors all mess up.....
Firstly Download these….
You gotta have the updated USB sync drivers.tht can be done from crackwhores guide.
http://forum.xda-developers.com/showthread.php?t=524619
follow it. According to the operating system you have.
When you are done installing the drivers. Restart ur pc n (incase of vista: press F8 before windows starts n from menu select disable signature reinforcement) everytime u plan to flash a new rom u gotta restart n disable the driver signature reinforcement if u had a normal reset earlier as vista on normal boot blocks these drivers.
After u have the drivers installed and working go to this link another crackwhores guide n
http://forum.xda-developers.com/showthread.php?t=505377
Download these 2 files “USPL GUI v 2.5.zip” “BlackstoneRUUWrapper.zip”
when you extract file USPL GUI v 2.5.zip your antivirus gives warning tht it is virus… its not… ignore that.
Now u have to download and install the official latest rom which works with touch HD (orange)to update your SPL to 1.54 .
go to this link
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
and from here download this file.
• RUU_BlackStone_HTC_WWE_1.56.405.1_Radio_52.62.25.3 4_1.13.25.24_Ship.exe
(note this rom is specific to UK devices n only this will work on orange hd…. If u download any other it will fail)
After you have downloaded and extracted the rom file. It will be named ruusigned.nbh make a new folder and in tht folder put this file and also extract that “blackstoneRUUwrapper” into it.
Now ur ready to start flashing process… for detail check the crackwhores guide to flashing. Im just writing short outline. Make sure you have at least 50% charge.
1.First turn off ur cell.
2.Hold down volume down button n press power button till u see a 3 colored screen with SPL 1.14000 n on bottom of screen there is “Serial”
3. Now connect your device to pc via usb cable. Serial will change to usb in couple of seconds.
4.Now run USPl.exe from tht USPL GUI v2.5 tht u had extracted earlier. A window will open. On tht click “RUN USPL” n in 5 to 10 secs it will run and show u message in end tht USPL loaded and happy flashing.
5.Ur cell screen will reload n now it will show “USPL1.54000” instead of “SPL 1.14000” and usb will disappear from bottom of screen. Just unplug the usb n replug USB will come up again.
6.Now go to tht folder with Blackstone RUUwrapper and RUUsingned.nbh file
7.Run tht BlackstoneRUUwrapper.exe
8.Follow the application by clicking next n checking boxes where ever needed.
9.At end it will start flashing ur rom. It takes 10 mins.
10.When finished your device will automatically restart.
11.While its doin tht unplug the usb. Remove the back cover n yank out the battery.
12.After 5 secs reinsert the battery n put on the cover
13.Now press n hold both up n down volume buttons n press the power button once.(but keep holding the volume buttons)
14.After 3 secs bootloader like screen will come up saying press vol up to restore factory settings.
15.Do tht
16.Whe finished it will say press vol up again to boot.
17.Do tht.
18.N ur done =) if u just wanted to get the latest official rom and this has updated your SPL to 1.54000 from 1.14000.
19.But if u want any cooked rom u can easily install tht following the same steps from 1. Using the cooked “RUUsigned.nbh” and u wont end up with any problems with screen colors with cooked roms….
Happy FLASHING
Click to expand...
Click to collapse
well regarding updating spl from 1.14 to 1.54 u need not install the full rom..
jus install hspl 1.56 olinex or if u want stock 1.54 then
1. dnload stock spl 1.56 from the tut thread
2. run uspl 2.5
3. wait fr bootloader to show 1.xx.uspl
4. remove and replg usb cable and confirm usb on white part
5. run hsplwrapper 1.56 olinex but do not do any thing on the ruu(wait fr files to extract in the window from where u ran the hspl wrapper)
6.copy the stock spl u dnloaded(ruu_signed.nbh) into the directory where files were extracted and allow to overwrite.
n thats all u need to get 1.56 stock..
yup u dont need stock rom if u just wanna get a cooked rom but if u want official update. thats the rom for orange sets.n do try both normal update n cooked rom of ur choice =)
Thank You Very much for the replies!.. didn't expect to get so many in the time interval. Will start the process in about 2 hours , and let you know about any complications of they arise.
Once Again, THank you
bilalperwaiz said:
Thank You Very much for the replies!.. didn't expect to get so many in the time interval. Will start the process in about 2 hours , and let you know about any complications of they arise.
Once Again, THank you
Click to expand...
Click to collapse
well this is a active forum..
n ya get back if need arises.
ur most welcome man
Thanks a lot......brilliant tutorial to debrand a orange touch HD to official ROM......

Help about flashing roms

Hi! I have a question about roms. I want to flash my rom with let"s say shadowmans win 6.5, but i dont know how, because everyone is talking about hardspl and branded phones. I have i stock rom now (6.1) and i have hardspl preinstalled, does that mean that i can flash any rom i want or what? What is the quickest way to flash and what can u do if flashing fails? I need a quick giude for dummies. Thanks for all your help!
the easiest way to flash is with custom RUU it is explaind in hspl Wiki- as you will use this to flash hspl
download newest hspl 1.83 olinex and flash it
http://forum.xda-developers.com/showthread.php?t=520312
download ROM
connect you topaz to pc in active syns mode
open CustomRUU it us usually included with downloaded ROM
follow the instructions
then you can flash the radio again use the wiki
http://wiki.xda-developers.com/index.php?pagename=Topaz_Radio_ROM
hope this can get you started
If you definitely have hspl 1.83 olinex installed (you can check from the 3 colour bootloader screen - completely switch off your topaz and switch on again whilst holding volume down key), then you can flash any ROM using just your microsd card instead of connecting to your PC.
Download the ROM of your choice and extract the .nbh file from the archive or folder. It will be the biggest file in the archive. Rename this to TOPAIMG.nbh and put it in the root (top level) of your microSD card.
Make sure your battery is near to full, then turn off and restart your Topaz in bootloader mode as described above. It will detect the ROM and ask you to confirm upgrade. Simple as that. When it's complete and says "success" you can restart your phone using the reset button.
If ever it fails, you can simply do it again. Or, take out your microSD, put it in a card reader and put another TOPAIMG ROM file there, re-insert, and reflash.
Don't forget to delete the TOPAIMG file afterwards.
You can flash complete ROMs this way or just radio ROMs, it's the same process. I like this method because it's self-contained and doesn't rely on connection to your PC. Only make sure a) olinex 1.83 is installed already, and b) there's adequate battery left.
Don't forget to make a note of your stock ROM so that you can download it again in case you ever want to go back to it, or if you send your phone in for service.
problem
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
I have checked that too, but i have hspl 1.33, does that mean i can flash any rom i want from my sd card or i must have 1.83 to do that?
Thanks for help
tommaazz said:
I have checked that too, but i have hspl 1.33, does that mean i can flash any rom i want from my sd card or i must have 1.83 to do that?
Thanks for help
Click to expand...
Click to collapse
you want the latest hard spl 1.83 so that there wont be any problems. all the chefs state in there rom thread to have that one too.
fs1978 said:
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
Click to expand...
Click to collapse
is your micro sd formatted with fat 32? must be formatted in order to flash a rom using a micro sd card first. you dont have to power down your device to flash from sd card either. just hold volume down and insert stylus in the soft reset hole. hold until bootloader screen comes up. after flashing a hard reset is recommended. thats when you power down the device. you have to wait till everything gets set up first though to get to where you can power down the device though. hold volume up and down button. while holding those buttons turn the power back on. then follow the instructions it says.
fs1978 said:
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
Click to expand...
Click to collapse
Is your ROM file named exactly TOPAIMG.nbh? Note the caps for the filename and lower case for the extension.
I was just reading another thread and apparently this is important for the bootloader to recognise it.
Please add one small comment to HSPL instructions
Few of us get "stuck" installing HSPL... Once you see a tricolor screen you are to follow RUU...but it says to be connected in activesync. yet if one looks on activesync you see your device is disconnected.
Please add "wait a minute" and just click OK on RUU. By then it is connected just doesn't show in activesync. Flash and all should be good.
Andy
I haven't burned a new ROM yet but have been getting the pieces together
I have an AT&T Pure which comes stock with WinMo 6.5 and also comes with
a Stock HSPL 1.83 (I believe 1.83 is required for all 6.5 and above?)
I think there is a potential area of confusion here for Pure users
(Especially since the other Topaz came with WinMo 6.1 and HSPL 1.33)
there is an OEM HSPL 1.83 and an Olinex modified 1.83 that will unlock
the phone.
Correct me if I'm wrong but
The one that is actually needed is the "modified"
1.83 OliNex (available here on XDA from Olinex as a sticky)
Can someone confirm this "subtle" difference???
I've gone to the tri-color Boot screen and the stock Pure only says
HSPL 1.83 (it does does not say OliNex)
my current understanding is that I will need to
burn the Olinex HSPL over my Stock OEM 1.83
before adding a new ROM??
One final question is after I reburn the new Olinex HSPL
Do I need to install the new ROM at that point?
Or could I use my phone? (with old stock Rom plus new HSPL)
Just want know if I'd be "off the air" at that point or not?
(So maybe I'll wait with R1+ over the latest Dutty Rom)
TIA
Hope this can at least promote some understanding
KJL
problem
--------------------------------------------------------------------------------
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
any idea on how to flash back to stock at&t rom for warranty purposes. i rmr seeing a post in the raphael rom section but nothing here. any ideas??? im turning this in for a tilt 2. sits perfectly in my car mount n looks like a micro mini netbook...haha....

Touch Diamond wont boot afrer Installing ROM

Hi. Yesterday i installed a new ROM on my touch diamond, after that my touch diamond won't start. And what's weird?? I can go to Bootloader and I can do a hard reset, but i can't connect with PC on bootloader and i can't enter Bootloader with USB Mode...plz help me
Solved !!
LOL. I tried for many times to go to USB Mode Bootloader pushing VOLDOWN+OK+Reset.....when i pushed VolDown and Rest...all done and now i'm flashing my new rom...thanks XDA Forum, Ur the best
i got a problem,after installing Mystery rom i cant start my diamond,when i turn it on,it stay at screen TouchDiamond and i cant do anything...any help? PLEASE!
markos807 said:
i got a problem,after installing Mystery rom i cant start my diamond,when i turn it on,it stay at screen TouchDiamond and i cant do anything...any help? PLEASE!
Click to expand...
Click to collapse
you can imitate the way of qemasoft to make your device go to the boot loader, then you flash back to the official ROM that you can get in http://shipped-roms.com/index.php?category=windows mobile&model=Diamond

Help! My Diamond cant boot and i want to flash it to Original

Hi everyone.
Ive got a MAJOR Problem here.
My Cell Phone doesnt start at all.
If i put it one the USB Cable it can Start up like 5 Seconds.
Then it Reboots and Reboots again and again by 5 Seconds.
If I Disconnect the Phone from USB screen turns Black Immediately...
I thought it could be the Batterie... but.. it worked just fine yesterday..
(have i Mentioned that this weird Sticker on it turned red..? Some kind of sign saying me it got wet?)
All this started as i got a Coloured screnn with saying ´´Serial´´ @ the bottom of the Screnn... just exact like the Flash Screen
I Flashed the Rom which is on the Internal Storage i put bevor. To bad it aint the Stock ROM!
Then i also tried Hard Reset.
But everytime i boot... i only get as far as 5 Seconds.
Is there any Chance to Flash this Baby with original ROM (Stock ROM, RADIO and SPL)
I want to send that Baby in... but if they find out i Flashed it... i wont get any Warranty... ;(
So PLEASE GIVE ME ANY ADVICES!!!!!
Try to flash with the original ROM. Go to HTC homepage-support, download the ROM and flash. It may help...
krisztian b said:
Try to flash with the original ROM. Go to HTC homepage-support, download the ROM and flash. It may help...
Click to expand...
Click to collapse
You only can Flash if u got a Active Sync connection.
So ... Cell cant boot... i cant flash...
HELP
Just go into bootloader mode (you have Hard SPL installed right?) by booting up the phone while holding down the volume down key. Then connect it to the pc with the USB cable and run the CustomRUU to flash another rom. Should work! Else you should try to MTTY (that solves the resetting stuff right?).
I was just about to say to try to get Diamond into bootloader mode manually. http://forum.xda-developers.com/showthread.php?t=405659
MTTY wont work... cause i cant boot at all
But THX for your help flashing it back to Original...
This Thread can be closed

Help : problem after updatin d ROM.

somehow i change the HardSPLWrapper from 1.56.OliNex to 1.14.OliNex.
then my HD stoped working and its show me the "red,green,blue,white" screen with this MSG :
BLAC100 300
SPL-1.14.0000
MicroP-BlackStone (LED) v6
Upgreade ROM code error please try again.
Click to expand...
Click to collapse
if i connect the cable its show me USB.
when i try to update the ROM version or update the SPL to 1.56.OliNex. it show me the MSG in the attachment.
plz tell me what to do. this is the second day without my HD. + im in philippense those days i dont know where to fix it.
thanx
Hard reset.
Try some hard reset and then do flash again to higher hard spl 1.56.
Rom.
If the hard reset doesnt help flash with stock rom and do te hard spl again.
mcnaget said:
If the hard reset doesnt help flash with stock rom and do te hard spl again.
Click to expand...
Click to collapse
thnx for ur efforts.
but still the Hard reset doesnt help.
i tried to flash the stock rom, but same problem.
its give me a MSG : 00028002 not allow
yabdoo said:
thnx for ur efforts.
but still the Hard reset doesnt help.
i tried to flash the stock rom, but same problem.
its give me a MSG : 00028002 not allow
Click to expand...
Click to collapse
Not sure if it helps, but maybe you can try flashing stock ROM using USPL?
yabdoo said:
thnx for ur efforts.
but still the Hard reset doesnt help.
i tried to flash the stock rom, but same problem.
its give me a MSG : 00028002 not allow
Click to expand...
Click to collapse
yes try USPL 2.5
ill go through it with you
CaponiND + jigners
thank you.
i tried the USPL 2.5
but still it show me spl-1.14.
and after updating the ROM.
its stuck on the setup screen : tap the screen to setup your device.
+ something wrong with the screen color.
Boot.
Remove battery for some time,try to get in to boot loader from device not from windows,restart windows if there are any usb connections or processes in windows that prevent from flashing. Insert usb cable in different usb port. Try on a different pc.
the boot problem is finished. after i change the USB port.
i update to SPL-1.56, then i update the ROM.
but still its stuck on :
tap the screen to set up your windows phone.
when i tap the screen, the screen comes bright. but nothing change.
and its vabirate for a second. from time to time while its on the set up screen.
thanx mcnaget but still i need a help.
Battery.
Remove the battery for 24 hours and try again.
24 hours more
ok ill try, thnx alot.
Battery.
I have read in some post that this could help but if it is a hardware damage than none of this would help.
I wish you best of luck to bring him back to life.
Regards.
thanx
still stuck at set up screen.
i notice some thing when i update, usually it show me in the box :
verify that you want to update the ROM version :
from :
Image Version : "the previous ROM"
to :
Image Version : "the next ROM".
but now its show nothing on "From": Image Version.
just show mo the Image Version of "TO".
See the attached Pic.
Rom.
Have you try manualy to go to boot loader.If you already have olinex 1.56 try some different stock rom.
yabdoo said:
but now its show nothing on "From": Image Version.
just show mo the Image Version of "TO".
Click to expand...
Click to collapse
This is normal behavior when flashing from/to custom made ROMs, at least with USPL (never tried HSPL )

Categories

Resources