hello sir,
i am new member of this forum.also i proud to be part of this forum.
i have one X1 XPERIA. BEFORE IT WAS CHINESE/JAPANESE LANGUAGE.
SO I ASK TO GSMHOSTING.
THERE I FOUND SOME SOLUTION. LIKE:
0. Make sure x1 is hard-spl first
1. Make sure your micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it your X1,
onto the storage card root
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right,
and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction
THEN IT SAY TO UPGRADE TO POWER BUTTON, I PRESS THEN PROGRESS
BAR COME IN SCREEN. THEN FULL UPGRADE SET LIKE RESTART....
BUT NOW ON WHITE LIGHT COME THIS WORD (LOADING.....)
TILL HERE I DO SUCESSFUL BUT NOW SET HANG ON (LOADING...)
I LEAVE 3 HOUR BUT SAME.
SO I REMOVE BATTERY AND PUT AGAIN AND POWER ON
COME ON SCREEN
TRICOLOUR & THERE IS SOME THING LIKE THIS:
CONTINITY UPGRADING ROM, PLEASE WAIT, THEN GO LOADING......
HOW TO REVIVE IT????
NEED HELP SIR.
Do you have a card reader?
If so, plug into PC and check if the ROM is indeed on the card and correctly named.
Device needs a full charge, this is imperative.
It is not a good idea to interrupt a ROM flash.
Report back with answers and I'll try to get you back up and running.
sattar_00977 said:
hello sir,
i am new member of this forum.also i proud to be part of this forum.
i have one X1 XPERIA. BEFORE IT WAS CHINESE/JAPANESE LANGUAGE.
SO I ASK TO GSMHOSTING.
THERE I FOUND SOME SOLUTION. LIKE:
0. Make sure x1 is hard-spl first
1. Make sure your micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it your X1,
onto the storage card root
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right,
and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction
THEN IT SAY TO UPGRADE TO POWER BUTTON, I PRESS THEN PROGRESS
BAR COME IN SCREEN. THEN FULL UPGRADE SET LIKE RESTART....
BUT NOW ON WHITE LIGHT COME THIS WORD (LOADING.....)
TILL HERE I DO SUCESSFUL BUT NOW SET HANG ON (LOADING...)
I LEAVE 3 HOUR BUT SAME.
SO I REMOVE BATTERY AND PUT AGAIN AND POWER ON
COME ON SCREEN
TRICOLOUR & THERE IS SOME THING LIKE THIS:
CONTINITY UPGRADING ROM, PLEASE WAIT, THEN GO LOADING......
HOW TO REVIVE IT????
NEED HELP SIR.
Click to expand...
Click to collapse
Hello!
Try this, then flashing again:ftp://x1:[email protected]/XperiaX1/TOOLs/X1_HardSPL_Utility.zip
Your spl is:spl-0.72.OliNex? If it is not the spl-0.72.OliNex version (check it on the tricolour boot screen ) will not succeed then the flashing.
HARD-SPL XPERIA X1 INSTRUCTIONS
Flashing Olinex Hard-SPL will not hard-reset your device
Nothing will be changed (except the SPL)
But it is recommended to backup your info first, just in case
1- Charge phone at least 50% (90-100% recommended)
2- Sync device, be sure activesync finishes syncing
3- Run "X1_HardSPL.exe
"
4
- Follow the on-screen instructions
WHAT YOU WILL SEE:
When "Loading..." bar shows in PC, check device screen
Phone goes into "bootloader mode" (tricolour screen)
Hard-SPL flashes automatically and device reboots
Done
TO CONFIRM A SUCCESSFUL HARD-SPL:
Go into bootloader mode (hold vol down key and press power)
Verify in the tricolour screen: "0.72.OliNex
"
augie7107 said:
Do you have a card reader?
If so, plug into PC and check if the ROM is indeed on the card and correctly named.
Device needs a full charge, this is imperative.
It is not a good idea to interrupt a ROM flash.
Report back with answers and I'll try to get you back up and running.
Click to expand...
Click to collapse
yes sir i make full charge battery.
and i rename to file "Kovsimg.nbh"
but sir how long time it take this process (approx.)?
oliolioli said:
Hello!
Try this, then flashing again:ftp://x1:[email protected]/XperiaX1/TOOLs/X1_HardSPL_Utility.zip
Your spl is:spl-0.72.OliNex? If it is not the spl-0.72.OliNex version (check it on the tricolour boot screen ) will not succeed then the flashing.
HARD-SPL XPERIA X1 INSTRUCTIONS
Flashing Olinex Hard-SPL will not hard-reset your device
Nothing will be changed (except the SPL)
But it is recommended to backup your info first, just in case
1- Charge phone at least 50% (90-100% recommended)
2- Sync device, be sure activesync finishes syncing
3- Run "X1_HardSPL.exe
"
4
- Follow the on-screen instructions
WHAT YOU WILL SEE:
When "Loading..." bar shows in PC, check device screen
Phone goes into "bootloader mode" (tricolour screen)
Hard-SPL flashes automatically and device reboots
Done
TO CONFIRM A SUCCESSFUL HARD-SPL:
Go into bootloader mode (hold vol down key and press power)
Verify in the tricolour screen: "0.72.OliNex
"
Click to expand...
Click to collapse
yes sir i am sure this is spl-0.72.OliNex
and i have "X1_HardSPL.exe .
but problem is that how to sync with pc? in this condition?
No need to sync with PC to flash via SD card.
If you have the ROM on the card and Hard_spl on the device, follow instructions listed in the thread.
DO NOT sync with PC until flash is complete.
augie7107 said:
No need to sync with PC to flash via SD card.
If you have the ROM on the card and Hard_spl on the device, follow instructions listed in the thread.
DO NOT sync with PC until flash is complete.
Click to expand...
Click to collapse
"Hard_spl on the device" I ALRADY DO THIS BEFORE. AND ROM IS IN THE CARD
AS RENEAME "Kovsimg.nbh".THIS FILE ARE .NBH FORMAT & SAME FILE IN RAR FORMAT.
BUT STILL SAME ONLY LOADING......(in blue colour) in white display light.
sir, it take how long time????
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
after that set show only this from last 1 hour.
i confused? how long will take??
not 100% as I'm very much an amateur at this , but that kovsimg file is WAY too small. What are you trying to flash on it??
If a full rom, the size will be in tens or probably a hundred and more MBs.
And a successful flash has taken me about 10 minutes in the past, but I've only done it twice.
the "kovsimg.nbh" is incomplete, it should be a lot bigger like the above poster has said, at least 70mb.
Im not sure if having a capital K has any affect.
Where did you get your rom from?
Sorry, im not familiar where the "Loading..." comes from.. is that before or after where you press the Power Button to start flashing the kovsimg?
Edit: nvm, loading is just before kovsimg.nbh is found. You will need to download the rom properly. Check the file size and make sure its big as in 100-200mb, and place it in the root of the storage card with the name "kovsimg.nbh" lower case.
That is correct.
The file you are showing is most likely the Hard_spl file which is about that size.
A full Rom runs from 130MB to 220MB depending on contents.
cykalu said:
the "kovsimg.nbh" is incomplete, it should be a lot bigger like the above poster has said, at least 70mb.
Im not sure if having a capital K has any affect.
Where did you get your rom from?
Sorry, im not familiar where the "Loading..." comes from.. is that before or after where you press the Power Button to start flashing the kovsimg?
Click to expand...
Click to collapse
"Loading" is normal. It will move from 1% to 100% as the ROM is flashed.
Yeah. I just went to the bootloader to check it out again.. normally i just spam the power button till it starts flashing.. hence i dont remember such a text
But ya.. it shows up just before it confirms the location of a proper kovsimg.. but i thought it would say "invalid image file" which happened to me once.. not get stuck in "Loading.."
I usually flash my phone once every week or two.. new releases of cooked roms are just that great ;D
esudl said:
not 100% as I'm very much an amateur at this , but that kovsimg file is WAY too small. What are you trying to flash on it??
If a full rom, the size will be in tens or probably a hundred and more MBs.
Click to expand...
Click to collapse
THANKS BRO.
U CAN GIVE ME FULL ENGLISH ROM PLEASE?(NOT RAPIDSHARE)
i search rom's but all rapidshare link,it's need premiur account.i don't have that. thatsway i need free (without account)
link.
There's a fine selection of roms on this forums.. worth checking out to see which one is for you, each has its features and specialties.
The question is.. do you want WindowsMobile 6.1 or 6.5? Want TouchFlo3D? 2.1 ("TR", faster, stable, less ram and battery usage) or 2.5? ("Leo", experimental, slightly sluggish and drains more battery than TR, but nicer looking and better "Home" screen); you can skip TF3D and opt for SBP Shell tooo...
My favorite is agent_47's Valkyrie Firestorm (Rhodium\TOPAZ) @ http://forum.xda-developers.com/showthread.php?t=512050
But be careful when installing your own applications as it may conflict with the rom and causes it unstable ._. if you want a lot apps you want to install, you may want to not use TF3D (you can use the rom but you can disable TF3D in home settings, which is normally defaulted to "Titanium (WinMo6.5)" home screen )
Edit: You can download from Rapidshare for free when you click the "free user" button which should be next to the "premium user" button and wait around 30-50 seconds before it allows you to download; you don't need a premium account ^_^
cykalu said:
There's a fine selection of roms on this forums.. worth checking out to see which one is for you, each has its features and specialties.
The question is.. do you want WindowsMobile 6.1 or 6.5? Want TouchFlo3D? 2.1 ("TR", faster, stable, less ram and battery usage) or 2.5? ("Leo", experimental, slightly sluggish and drains more battery than TR, but nicer looking and better "Home" screen); you can skip TF3D and opt for SBP Shell tooo...
My favorite is agent_47's Valkyrie Firestorm (Rhodium\TOPAZ)
But be careful when installing your own applications as it may conflict with the rom and causes it unstable ._. if you want a lot apps you want to install, you may want to not use TF3D (you can use the rom but you can disable TF3D in home settings, which is normally defaulted to "Titanium (WinMo6.5)" home screen )
Edit: You can download from Rapidshare for free when you click the "free user" button which should be next to the "premium user" button and wait around 30-50 seconds before it allows you to download; you don't need a premium account ^_^
Click to expand...
Click to collapse
it is WindowsMobile 6.1 . already say it was chinese/japanese lang.
so i want english. if you recomand any rom's good. my costumer give too tension me. thatway i need help to this.
Actually i from nepal here too slow the internet.thatsway i try to download
come too much problem in rapidshare.therefore i need another link.
thank you.
Well, I'd say go for Agent_47's Valkyrie Firestorm (Rhod/Topz) version 5.0.28005, download it from his FTP.. I downloaded from that on a 56k dialup speed (capped internet.. bloody Australia) which took 6 hours and it came out perfect
Check out his thread @ http://forum.xda-developers.com/showthread.php?t=512050; sorry i cant hotlink people's stuff.. so you'd have to visit their thread
If you have time to play around a few roms to test with, i'd recommend MrRusch & WildChild - Untamed @ http://forum.xda-developers.com/showthread.php?t=568918
Also, check the other cooks' work too
cykalu said:
Well, I'd say go for Agent_47's Valkyrie Firestorm (Rhod/Topz) version 5.0.28005, download it from his FTP.. I downloaded from that on a 56k dialup speed (capped internet.. bloody Australia) which took 6 hours and it came out perfect
Check out his thread @ http://forum.xda-developers.com/showthread.php?t=512050; sorry i cant hotlink people's stuff.. so you'd have to visit their thread
If you have time to play around a few roms to test with, i'd recommend MrRusch & WildChild - Untamed @ http://forum.xda-developers.com/showthread.php?t=568918
Also, check the other cooks' work too
Click to expand...
Click to collapse
thank you bro help me.
at last i want to know this files also flashing via sd card?
any others file also keep in sd card??
please add me to your massanger
id is : [email protected]
thank you.
You can flash any kovsimg straight from a SD card, just make sure it's named correctly and it's placed in the root. You can have other files/folders on the SD card as well, it wont affect it, so no need deleting everything before flashing. The only file that will be used in the flashing of the device is whatever's named kovsimg.nbh (sp?) and nothing else.
One advice after flashing is.. hard reset the device straight after. Hardreset as in pressing and holding the two silver softkeys then press and release the power button, follow the instruction (press R and then Spacebar on the hardware keyboard). You can only hardreset when the device is off first.
Hard Resetting will get rid of a lot of problems which didn't occur for other people until the applications you install on top conflicts with the system (mostly with TF3D)
Related
Hello Everyone,
My BA is stuck at the Splash Screen, I suspect that the Bootloader is corrupt. Does anyone know how to flash it?
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
imatrix's suggestion.
@imatrix
Followed the steps before, and followed them again.. I'm still stuck.
Something interesting happened though:
There are two horizontal stripes across the splashscreen now.
I already tried to flash the OS, It doesn't work with the standard imate flash executable (It used to work before) and now I'm getting a 'MODEL ID ERROR' when I try to flash it using the BAupgrade... executable.
I tried with the MAupgradenoid tool, it flashes but I still get stuck on the splashscreen...
Thanks,
Wadih
BlueAngel Bootloader
Anyone has a way to either dump a bootloader file for the BA (Providing the file of course) or alternatively directives to copy it from another device (From the same make, i.e. Imate PDA2K) ?
Many thanks,
Wadih.
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
@imatrix
imatrix said:
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
Click to expand...
Click to collapse
I did, but as I specifed in me earlier post, eventhough the MAUpgradenoID flashes the files, I still get stuck at the splashscreen.
Interesting point: After flashing witht the MAUpgradenoID, I try reflashing back with the BAupgradeid.. I get the Model Error ID error back..
Something in the BA is wrong, and I believe it may be in the Bootloader. So, is there a way to replace the bootloader itself?
EDIT: By the way, I can't seem to be able to place a WM5 rom instead of the WM2003, although the flashing procedure starts, it quickly ends (i.e. without the percentage bar appearing) and says that the flashing worked successfully... But nothing gets actually flashed.
Many thanks for the help imatrix.
Regards,
Wadih.
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
@imatrix
imatrix said:
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
Click to expand...
Click to collapse
Thanks for the link, but how do I copy/get a clean boot bin file? (Which app, syntax, etc...)
Cheers,
Wadih.
BlueAngel froze on isalling wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
BlueAngel froze on installing wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
100/100 work
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
Click to expand...
Click to collapse
thaks br very good
Hi, I have the problem, that windows does not recognize the Blue Angel any more, so no "WCEUSBSH001" available. Any help??
Thx
Hi people,
first - Excuse please my english
We (me and Jimm98y) in Czech republic are making ROMs to HTC Wizard and
some peoples say us: "Hey men, Why you don`t write about your ROM to
XDA-dev ?" Many posts on forum ce4you.cz is like:
Code:
Thank you people I think that is the best ROM for Wizard ever
So.... We´re here !
[size=+1]Please do NOT remake our ROM, because We were done a hard
work on it and we don´t want any steal of our job[/size]
So what´s in?
- OS 2.26.10.2 with aku 2.3 (we think that is still better then 3.2)
- GSM 2.25.11 (I think it is better than 2.47.11)
- HTC logo (surprise)
- Splash screen (Windows mobile loading...)
- ExtROM (many things unusuall things)
- IPL/SPL - not included
That ROM works only on CID-unlockded HTC Wizard
Base features:
IN ROM
- Program to browse contacts via Bluetooth
- Total commander
- OmapClock
- ScreenOff
- WM5torage 1.73
- Smartskey
- Default vlack theme
- Dialer vista skin by jimm98y with T9 and big buttons
- Skin for WMP ala WMP 11 by Xcilion (my rebuild)
- Voice speed dial settings
- HTC X-button
- Soft key applet
- Many registry tweaks (only universal)
- Cleartype by default
- deleted much unusable things
- Camera patch
- Removed green battery
- Removed MSN
IN EXTENDED ROM
Automatic
- Midlet manager (big program - if you do NOT need it - skip install and install extROM manually)
- CAB, that shows version of extROM
- Setup MMS folder
- SMS delivery fix (fix of non-shows names on SMS delivery)
Manually
(in that section there are programs, what you can manually install from the
shortcut in Start/programs/Install)
- Batti 2.1 (CZech program by "David Andrš" to show battery in upper taskbar - now fixed to english version)
- Wifi g enable (cab with one register to quick enable/disable by uninstall
wi-fi b/g)
- Mchat2.1b (icq client)
- .NET cf2
- TCPMP with all plugins included AAC
- Windows live messenger
- And configuration cabs to Czech Republic GPRS, but you don´t mind them
All packed to
- 45 MB free ROM (before customization)
- 42.3 MB free ROM (after customization)
- 32.2 MB RAM (always)
IN rom there is default clock to 252 MHz (by omapclock + smartskey) and you
can quickly in: Programs/overclock set any other "base" clock.
I think there are plenty of things to wrote, but I have not time to next New Years
EVE and here you have a video, what will put your minds about that ROM:
You can download some foto templates, because in ROM there is only one
czech home page
you can get our banner
[size=+1]download Superrom v 1.1 by ppctuning.org[/size]
SupeRom
Thanks guys As i write this I'm downloading the Rom. I'll let you know how it works for me.
Thank you guys, I will try it this weekend and give a feedback.
thanks, it's great to see new rom cookers here as Ive always feel that every cook brings a little something to the table!
Installed with no problems. Well slight problems with configuring the battery meter as it is in Czeck! - so some trial and error here but it works very well.
Everything works fine with T-mobile in the U.K.
Early days but could be the best ROM yet.
I have tried all the others and up to now have been using
Risidoro. This is similar but may just edge Risidoro into second place.
Very well done.
An english version of the battery meter Batti 2.1 can be found at:-
http://andrsd.blogspot.com/2006/08/batti-21.html
Makes it a lot easier for us english to configure!
Does this ROM have Crossbow Icons?
aminsamizadeh said:
Does this ROM have Crossbow Icons?
Click to expand...
Click to collapse
No it does not.
After having some problems with Molski's, battery drain etc. I installed yours, up until now running smoothly.
Maybe worth considering the crossbow icons, because people are waiting for this for 3 weeks already. It seems very important.....
..........
Thanks guys
CR Rulez..
Okay... So I've done the install.. First off, it looks an works great, almost..
It can't connect via USB anymore..
It doesn't even start charging the battery...
Any ideas of what I've done wrong? The whole install went perfectly well and I had my wizard connected untill it said that the install was completely finished...
edit: I've attached it to my regular charger and doesn't work anymore to.. It did worked fine yesterday... Any thoughts?
gvink said:
Okay... So I've done the install.. First off, it looks an works great, almost..
It can't connect via USB anymore..
It doesn't even start charging the battery...
Any ideas of what I've done wrong? The whole install went perfectly well and I had my wizard connected untill it said that the install was completely finished...
Click to expand...
Click to collapse
Unplug the device from USB, reboot it and then plug in the USB cable after it boots.
vasquja said:
Unplug the device from USB, reboot it and then plug in the USB cable after it boots.
Click to expand...
Click to collapse
After the boot is completed or when it gives the startup screen?
edit: It seems that my wizard has given up..
When I turn it on it does all the 'checks', than it gives the Splash screen (Windows mobile loading...), and after that the screen sort of flashes.. It actually turns into stripes, than
it turns into grey -> black, and it boots up again.. It keeps doing this routine.. It looks to me it's sort of broke? When I plug it in via USB it doesn't make any difference...
PLZ help me here...
making cabinet files for ppc?
Wanted to know if anyone could tell me how to make cab. files? What software to use? Please HELP!!! Wanted to make cab to install.
gvink said:
Okay... So I've done the install.. First off, it looks an works great, almost..
It can't connect via USB anymore..
It doesn't even start charging the battery...
Any ideas of what I've done wrong? The whole install went perfectly well and I had my wizard connected untill it said that the install was completely finished...
edit: I've attached it to my regular charger and doesn't work anymore to.. It did worked fine yesterday... Any thoughts?
Click to expand...
Click to collapse
Try to go to:
Code:
Start\Settings\connections\USB to PC
It can help if you AS on PC is quite broken
gvink said:
After the boot is completed or when it gives the startup screen?
edit: It seems that my wizard has given up..
When I turn it on it does all the 'checks', than it gives the Splash screen (Windows mobile loading...), and after that the screen sort of flashes.. It actually turns into stripes, than
it turns into grey -> black, and it boots up again.. It keeps doing this routine.. It looks to me it's sort of broke? When I plug it in via USB it doesn't make any difference...
PLZ help me here...
Click to expand...
Click to collapse
Try this one i think u flash ur previous ROM which is still locked...it happens before with me.
1.In your PC (task manager) "end the task for wescomm.exe" you can find this in the processes window (this is related with activesync installed on your PC).
2.Get your phone in bootloader mode. Like this : hold the "voice dial" and shortly press the reset button by stylus, release the reset button and wait for the USB color screen
3.Now connect your USB cable to your phone. And start MTTY_updateROM.exe as attached . After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
4. Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
5. To revived your device you have to downgrade it to 1.05 Rom ( ftp://xda:[email protected]_11210_WWE.exe )
6.Be sure that you have to unlock first your device before you will flash again with another ROM like V2.XX or more.
arliejoseph said:
Try this one i think u flash ur previous ROM which is still locked...it happens before with me.
1.In your PC (task manager) "end the task for wescomm.exe" you can find this in the processes window (this is related with activesync installed on your PC).
2.Get your phone in bootloader mode. Like this : hold the "voice dial" and shortly press the reset button by stylus, release the reset button and wait for the USB color screen
3.Now connect your USB cable to your phone. And start MTTY_updateROM.exe as attached . After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
4. Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
5. To revived your device you have to downgrade it to 1.05 Rom ( ftp://xda:[email protected]_11210_WWE.exe )
6.Be sure that you have to unlock first your device before you will flash again with another ROM like V2.XX or more.
Click to expand...
Click to collapse
Sorry i coudnt attached the file MTTY_updateROM.exe anyway here is the link...(http://wiki.xda-developers.com/uploads/romupdate.rar
Hey mans - I think that is quite offtopic.
BTW - I have fixed the version of batti 2.1 to English version.
Johnnnnnnnnnny said:
Hey mans - I think that is quite offtopic.
BTW - I have fixed the version of batti 2.1 to English version.
Click to expand...
Click to collapse
sorry...for that
arliejoseph said:
Try this one i think u flash ur previous ROM which is still locked...it happens before with me.
1.In your PC (task manager) "end the task for wescomm.exe" you can find this in the processes window (this is related with activesync installed on your PC).
2.Get your phone in bootloader mode. Like this : hold the "voice dial" and shortly press the reset button by stylus, release the reset button and wait for the USB color screen
3.Now connect your USB cable to your phone. And start MTTY_updateROM.exe as attached . After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
4. Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
5. To revived your device you have to downgrade it to 1.05 Rom ( ftp://xda:[email protected]_11210_WWE.exe )
6.Be sure that you have to unlock first your device before you will flash again with another ROM like V2.XX or more.
Click to expand...
Click to collapse
Great! It looks like it's working perfect..! Only the part with the updater isn't completely clear to me... I can get the USB color screen and hit the "r2sd all" in the blank sheet. It immediately gave the Cmd> and a white bar with USB in it below the screen on my wizard.. ?
(immediately after I entered my way through the "r2sd all" command) It doesn't give anything extra...
Any more thoughts
SuperROM 1.1 WWE
Hi all,
I flashed that molskis ROM and than Superrom 1.1 WWE by ppctuning.org and I must say:
The SuperROM is the best ROM for wizard, much better than molski, ridsoro, faria etc! There are also changes right in system, but much more.
This ROM is very fast and stable. The system is faster, without overclock (I disabled it), than in other ROMs overclocked to 240MHz! After HR it has 45 MB free ROM and 32 MB free RAM. There are preinstalled some usefull programs (only freeware) and you can optionally install much other programs from extended-rom.
I'm dizzy reading all the threads, information overload, so thought I'd just post the question! This is all a bit scary and I'm a complete newbie so take it easy on me... and feel free to dumb everything down as if I were a child.
I live in Australia and have a Treo 750 with Software Version TREO750-1.15-ROW. It seems to be unlocked but still has the Telstra splash screen, although I use it with Vodafone. I want to upgrade to WM6, and from what I can tell I should upgrade using Treo750_2_27_ROW_EN_DesktopUpdater.zip (which I now have). Is this right? Should I skip straight to the WM6.1 upgrade? Are these official/safe?
I am running 32-bit Vista with SP1 on my laptop.
I found instructions on Palm's site here:
http://www.palm.com/au/support/treo750/downloads/wm6update.html
Are those the instructions I should follow? Is that all I need to do? I keep seeing references to the "Bootloader Method" or the "SD Card Method" or the "Cheetah Method". What are all these alternative methods? Which are the advantages of each? I've seen various different instructions, some involving renaming some .nbh file, etc. What is the definitive method?
I saw the sticky thread for the "Cheetah Hard-SPL and SIM Unlocker"... what is that utility for? Are the instructions for it in the download itself? (I didn't see it in the thread) What are "cooked" ROMs and why should I be interested? Where can I find them?
Sorry for the newbieness... thanks so much to all who respond!
upgrade to WM6
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Update Successful
Thanks mate, I'm not brave enough to try the wm6.1 upgrade yet, but I did manage to upgrade to wm6 with the Updater, even though my device was "not supported". I ended up using the method where you edit the payloads.xml file before clicking 'start' so that it accepts your current device version, etc. I'm all good now.
libal said:
If you want to upgrade to the official palm WM6 rom - then you use Treo750_2_27_ROW_EN_DesktopUpdater.zip and it is very simple - just connect the PPC to your computer . (as I know better to do it with a computer with WINXP and Activesync) , then run the program in the file Treo750_2_27_ROW_EN_DesktopUpdater.zip, and that's it.
If you want to upgrade to other roms like 6.1 normal or lite that you can find in this forum - then you need the other methods (there are two as I know - bootloader method or Kaizer..somthing method). Well, I wrote a guide how to upgrade to WM 6.1 lite using the bootloader method , I just sum up from this forum :
1. Download the rom file and the radio file:
Rom file from here : http://rapidshare.com/files/89355384/Treo750_WM6.1_WWE_Lite.rar
The radio file from here :
http://rapidshare.com/files/89336971/Treo750Radio1.54.07.00.rar
2. Download the Hard-SPL from here :
ftp://xda:[email protected]/Cheetah/Unlocker/CheetahUnlocker.rar
3. Format mini SD card 32 FAT , using a card reader or other way.
4. Do a HARD-SPL with the CheetahUnlocker file ( step 2) . Connect the Treo with your computer using Active sync(for WINXP) and run the file. Use those steps:
- Click the Step 1.... wait the progress bar reach 100%
- Now watch the Screen on your PDA it will launch 2 times verification...
- just click YES ...wait.. and YES again.
- after finisih... wait until the activesync go green again.....
- Now click the Step 2... wait the progress bar reach 100%
- Watch the screen again... same thing.. it will launch 2 times verification.
- click YES ...wait.. and YES again.
- After finish it your PC screen will shows some popup. ignore the reading bla bla bla... about ask u to click ok.
- Just wait untill your activesync go green again.
- Now click that bloody Popup OK button.
- The unlocker app will shows up again..
- Then you will see errors saying.. continue, cancel...etc... bla bla... just click continue.. error message.. iqnore it and then just finish it.
- Now your Cheetah should be on HARD SPL mode.
5. Install the ROM :
a. Using Winrar get the file from step 1. It's name should be : CHEEIMG.nbh
b. Copy the file to the root of the mini SD .
c. Do BOOTLOADER:
1. turn phone on
2. press the MEDIA button AND at the same time with the stylus the RESET PIN
the MEDIA button is the 3rd button on the left side of the phone, under the volume button
the RESET PIN is under the MINI SD card cover
3. keep holding the MEDIA button (left side of phone) until you get the 3 color screen
Wait until it finishes. Then Hard reset the device when prompted. To hard-reset, hold the End key while pressing the pin reset button. Answer “yes” to “Erase all data” prompt.
6. Flash the radio at the same way – just copy the radio file to the mini Sd – it should be the same name. (CHEEIMG.nbh ) .
7. Download the Palm SMS file from hereYou need it only for the lite version)
http://rapidshare.com/files/99335294/threadedsms.rar
or
http://www.megaupload.com/?d=H63TXUP4
And install it as regular software (Copy to the mini SD and run it from the Treo.)
And that it all !!
Do not restore from your backup (You can restore only your data files).
Good luck !!
Click to expand...
Click to collapse
Did everything - step by step but nothing!
still the color screen with the word serial in the bottom!
What is wrong ???
Thanks in advance,
Nir
Got it!!
Turned out vista is displaying fat32 file system no matter what the file system is...
Nir
WM 6.1 Upgrade
Can anyone tell me where the AT&T Upgrade for the Treo 750 is to version 6.1. I have seen many different posts here that show many different links and different downloads with different loading instructions. Is there anything out there that is clear? I am willing to give it a try, but I am not exactly sure of which download to try. Thanks for your help.
Hi, I need your help. I read some of the XDA tutorial and I don't understand it.
Can someone guide me, step by step, how to upgrade to Windows Mobile 6 from 2003? I don't want to mess anything up, and currently have none of the files.
read wiki there is a upgrade wizard which will guide you
xplode said:
read wiki there is a upgrade wizard which will guide you
Click to expand...
Click to collapse
"I read some of the XDA tutorial and I don't understand it."
On it it says...
"If you plan to easily revert back to WM2003 or you don't want those extra MBs (Mega Bytes) on your BA, skip the next steps."
Also it says
"In WM5 and WM6 you are not using your RAM as storage for programs or documents anymore. Instead of RAM you are using Storage - because as we said before, no data is lost when your battery runs out.
Because of this, it's a good idea to merge your ExtROM with Storage to one "BIG Storage". (You will not install anything from ExtROM. You're not using non-persistent memory for storing programs anymore. Instead of ExtROM you can use SD or MMC card (Memory card), or install the hotfixes once after the flashing)"
Is there a way I can keep 2003, and also WM6? Or can I only have one in my phone? Do I do those steps? Do I skip them?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade1_WM2003SE0
I just need someone to guide me step by step, where I can ask questions, etc.
I also need tips, and information.
Do as xplode said. Follow the Wizard.
As per your question, [highlight]do not skip steps!!!![/highlight] All instructions are there for a reason!
And finally, you cannot have a dual boot on the Blue Angel. You can have either 2003 or WM6, but not both at the same time. You can always flash back and forth...
If you have questions, please search before you ask. And then, if the answer is not found, then ask someone.
I'm kind of stuck now... Not sure if I'm in bootloader mode or not, and when I run "MaUpgradeUt" it says "ERROR 150: ROM UPGRADE UTILITY ERROR"
...What do I do now?
if you are in botloader mode on your screen thould be Serial or USB (when connected to pc) if you want i can guide you over skype or msn or icq
I would love if if you could.
Please add XeneRoX @ Hotmail.com (separated it so a spammer bot doesn't catch it)
XeneRoX said:
"I read some of the XDA tutorial and I don't understand it."
Click to expand...
Click to collapse
Me too I did not understand the wiki when I used to be a newbie here, but I kept on reading it until my brain hurts, but what do you know I got it after reading the whole wiki for 3x.
On it it says...
"If you plan to easily revert back to WM2003 or you don't want those extra MBs (Mega Bytes) on your BA, skip the next steps."
Click to expand...
Click to collapse
It simply means that if you are OK with the default settings/partition of the internal storage/memory of you BA then skip the next steps which I dont recommend!!!
Also it says
"In WM5 and WM6 you are not using your RAM as storage for programs or documents anymore. Instead of RAM you are using Storage - because as we said before, no data is lost when your battery runs out.
Click to expand...
Click to collapse
In WM2003SE BA use RAM as a storage medium hence if the BA resets itself in anyway you lost everything in it, unlike in WM5 and WM6 onwards we use SD CARDS as storage medium hence even if we SR (Soft Reset) or HR (Hard Reset) our BA nothing will be erase on the SD card, so those pics of naked girls, those asian scandals on your SD Card won't be erase..lol
Because of this, it's a good idea to merge your ExtROM with Storage to one "BIG Storage". (You will not install anything from ExtROM. You're not using non-persistent memory for storing programs anymore. Instead of ExtROM you can use SD or MMC card (Memory card), or install the hotfixes once after the flashing)"
Click to expand...
Click to collapse
same thing, if I were you I will follow all the steps and will not skip..not even one step!
Is there a way I can keep 2003, and also WM6? Or can I only have one in my phone? Do I do those steps? Do I skip them?
Click to expand...
Click to collapse
Yes there is a way you can keep your WM2003se stock ROM...you can use ROM DUMPER..BUT...I don't recommend that because...sorry to say...if you are having a hard time upgrading you BA even if WIKI is there then you'll get a very hard time with ROM DUMPER .
You can only have one OS INSTALLED at a time on a PPC. I emphasized INSTALLED because you can have android copied on you SD even if you have one OS INSTALLED on your BA...does is sound clear? Hehehe
NOW....
Before you upgrade your BA keep this is mind...it's a warning...a WARNING so you will not sue xda-dev or any BA ROM cooker if something BAD happens to your BA. But don't worry 1 out of 1000 BA owners brick their BA while upgrading. Because they upgrade their BA with 10% battery life. Where did I get the 1 out of 1000 statistics? Just a guess..a wild guess but it's near to reality
WARNING
IF YOU PROCEED, YOU MAY TOAST YOUR PHONE. THERE'S NO COMEBACK. THERE'S NO GETTING ROUND THIS. READ THE INSTRUCTIONS FIRST OTHERWISE YOU'LL PROBABLY BREAK YOUR PHONE PERMANENTLY. THIS WILL VOID YOUR WARRANTY. DO YOU UNDERSTAND? DO YOu? ANSWER ME YOU...lol
Click to expand...
Click to collapse
- Download unlocker.cab DOWNLOAD HERE
- Download Repart_Doc.exe DOWNLOAD HERE
- Place both of them somewhere on your Pocket PC. For example in \temp but anywhere is fine. All the command below are to be executed on your Pocket PC, not on your PC.
- Install xda-developers_Unlocker.CAB by tapping on it in filemanger (from the directory where you put it earlier)
- Then go to start -> Programs -> ExtROM tools -> then first run "unhide", then "Unlock".
- Do a soft reset. (you know how to do a SR, right?)
- Once your Pocket PC is restarted, locate the Repart_DOC.exe file with your filemanager and start it.
- Set the size of Extended ROM to 128 kb (which is already the default).
- Press "Format now!" and wait until it is done (A few seconds). You will see a message that it is done. (You will get an error message about your storage, just press yes and wait a few seconds.)
- Soft reset your Pocket PC.
NOW YOU ARE DONE WITH THE FIRST PART AND I HOPE I AM MAKING IT EASY FOR YOU AND FOR EVERYONE.
Now, I RECOMMEND you to use Windows XP and of course Active Sync 4.5.
1. Download the BA ROM that you desired. It can be WM6, WM6.1 or WM6.5 and you can find all the download links of this ROMs on our BA wiki (and I am the one who updated that and put those links.)
2. Save that ROM on your computer. (anywhere will do) If it is zipped or rar, then unzip it or unrar it.
Here are the files that should be inside that ROM folder (well this are the files that I have every time I flash my BA, just correct me guys if some of this are not really needed):
EnterBL.exe
GetDeviceData.exe
HTCRUU.dll
RUU.dll
BaUpgradeUt.exe
MaUpgradeUt_noID.exe
HTCRUU.conf
RUU.conf
vbscript.dll
nk.nbf
SetOperator.bat
3. Temporarily remove your SD Card (it may work for you with the SD card still in your BA, but you may not be able to enter USB mode when cradled).
Just remove your SD Card from you BA and the SIM card too just to make sure.
4. Put your device into Bootloader mode by pressing and holding the "Power" & "Record" buttons, and then press the Reset Button. Ooops before I forgot make sure you do a Hard Reset on your BA first.
Press and hold the "Power" & "Record" buttons, and then press the Reset Button until “Serial” shows on screen.
(Some BlueAngel shows "Serial" at the top and "V2.07" at the bottom.)
NOTE: The screen will not be backlit, so it may appear the phone is not in bootloader mode.
Look carefully.
When the USB sync cable is inserted into the phone and the computer, "Serial" will change to "USB", provided that the phone detects the connection.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Connect the phone to the sync cable/cradle.
7. Now you can execute the installer file. (BaUpgradeUt.exe or MaUpgradeUt.exe) You will see this window:
8. When the upgrade is completed, you must perform a Hard Reset.
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
Put back your SD Card and you SIM card.
And there you go...I hope this makes upgrading easy for you and for everyone else. Did I missed something guys? Let me know.
WOW this is the longest post I've ever had since I started here...hehehe...just killing some TIME.
Yes!!!!!!!!!!!!!!!!!!!!!!!!
But is awsome men! really good work this is really a clean explanaition an dmaybe a refreshed how to upgrade....! truly!
thanks thanks thanks hehehe
Hi
I managed to use extrom as a part of rom, just like 2k3 does it, but some better.
This rom is 6.5 23140 fully provided, with EzInput, MS Office 2010 and Esmertec Java
I also got 236% in tcpmp benchmark, comparing to 157% in 23668. All important drivers are moved to xip to speed anything up.
Sounds good enough ;>?
Also I activated media control in lockscreen and fixed Internet Explorer
After installation you will get 2 partitions, root \ and Storage.
Some screens:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How to install? It's not that easy, read it carefully:
1. Download MTTY attachment, download Rom (link above).
2. Put your phone into bootloader and put into crandle
3. Run MTTY and click USB button. Then type in white field "task 28" without quotes and wait 5 seconds. Some confirmation informations should appear.
4. Close MTTY, Unpack Rom, run Upgrade.exe, having 3 files is important (nk, ms_ and upgrade)
5. Flash normally. Updating process will take more time than always!
6. After upgrade completed, take hima out of crandle, JUST RESET, Do not hard reset!!, and IMMEDIATELY put into crandle!!.
7. Wait until installation message will apear, after reading click Continue and then wait until device get rebooted. 5 minutes is okay to wait.
8. When device rebooted, don't do anything and wait until Debug message will appear, saying Extrom got unblocked, then click on OK.
9. Installation finished, click FINISH! and wait some seconds, after doing all stuff Welcome will appear.
10. Tap on screen, calibrate screen, set time, and enjoy
Link to this test:
http://www.4shared.com/file/ArKkI1Ls/Ext23140test.html
this looks like another hima historic hurdle has been passsed !!
will be trying soon..
sounds cool,real good about being able to use extrom as a part of rom...amazing !!
one small question in step 6. you mention JUST RESET is that just a matter of pressing the reset button and no other button ?
or is it a RESET where you have to press a few buttons at the same time like when you put the hima in bootloader mode ?
keep up the amazing work !!!
Nice aero, to see, that you go, where noone else ever had been before!
aero you are a legend!!
I of course WILL be trying this!
EDIT: There is no usb button there is only com1 and com2 in a drop down menu.
help!!
flyboyovyick said:
aero you are a legend!!
I of course WILL be trying this!
EDIT: There is no usb button there is only com1 and com2 in a drop down menu.
help!!
Click to expand...
Click to collapse
advanced15 said:
will be trying soon..
sounds cool,real good about being able to use extrom as a part of rom...amazing !!
one small question in step 6. you mention JUST RESET is that just a matter of pressing the reset button and no other button ?
or is it a RESET where you have to press a few buttons at the same time like when you put the hima in bootloader mode ?
keep up the amazing work !!!
Click to expand...
Click to collapse
If there is no USB do this:
Disable USB connection in Activesync
Remember to have himalaya in bootloader mode and on USB, lol obvious
If none of this helps, tell me what windows do you use
--
With JUST RESET i mean JUST RESET, just put anything in reset hole and don't press anything
aeroflyluby said:
If there is no USB do this:
Disable USB connection in Activesync
Remember to have himalaya in bootloader mode and on USB, lol obvious
If none of this helps, tell me what windows do you use
--
With JUST RESET i mean JUST RESET, just put anything in reset hole and don't press anything
Click to expand...
Click to collapse
I use windows 7, it shows com1-3
flyboyovyick said:
I use windows 7, it shows com1-3
Click to expand...
Click to collapse
Also did you installed this driver? (Vista = 7)
http://forum.xda-developers.com/showthread.php?t=428469
// This formatting mess is required because some people repartitioned theirs DoCs to remove EXTRom, so I don't really want to know what would happen without it.
When I upgrade,there are : error 112
why can it happens?
what will I do?
thanks
testing it now... will post report after... finger crossed..
done it..working now..
one question.. since memory in main is almost full thus this means i cant no longer install some programs?
main storage memory only now 1.58mb and programs 65.62mb,while storage is 15.96mb....
jonrols said:
done it..working now..
one question.. since memory in main is almost full thus this means i cant no longer install some programs?
main storage memory only now 1.58mb and programs 65.62mb,while storage is 15.96mb....
Click to expand...
Click to collapse
Why not to install on \Storage ?
It's not removeable
When I upgrade,
error 112
can you help me
arifurrokhman said:
When I upgrade,
error 112
can you help me
Click to expand...
Click to collapse
Hi arifurrokham,
If i'm not mistaken you've disabled the allow usb connections in the activesync connection settings before running mtty to show usb. After finished running mtty just enable the allow usb connections before running the upgrade to address error 112. Hope this helps
japo_g said:
Hi arifurrokham,
If i'm not mistaken you've disabled the allow usb connections in the activesync connection settings before running mtty to show usb. After finished running mtty just enable the allow usb connections before running the upgrade to address error 112. Hope this helps
Click to expand...
Click to collapse
This shouldn't because Upgrade tool disables AS automatically.
RUU LOG
08:04:09 Connection with USB
08:05:57 Begin stage 1
08:06:27 CE Erase retry 1
08:07:08 CE Erase retry 2
08:07:48 CE Erase retry 3
himalaya screen : serial
v 1.03
when I update : error 112
AERO...Can you help me...
excellent aeroflyluby !!!
i have run this excellent stuff..
all working good so far....
question ? after looking at the "ms_.nbf" with "er2003edit" i see that most of the actions to make extrom as part of rom is done with this.
with you permission? would it be possible to use this "ms_.nbf" with any "nk.nbf/ROM" so i could have the AMAZING extrom as part of rom on any ROM i like...
is this possible? if i follow the exact same guide but just change the "nk.nbf" ?
aeroflyluby keep up the great work !
advanced15 said:
i have run this excellent stuff..
all working good so far....
question ? after looking at the "ms_.nbf" with "er2003edit" i see that most of the actions to make extrom as part of rom is done with this.
with you permission? would it be possible to use this "ms_.nbf" with any "nk.nbf/ROM" so i could have the AMAZING extrom as part of rom on any ROM i like...
is this possible? if i follow the exact same guide but just change the "nk.nbf" ?
aeroflyluby keep up the great work !
Click to expand...
Click to collapse
Look, extrom have cabs, autorun, some exe's and config. ROM part is to unhide extrom, then run autorun and after installing all, device will reset, clear.exe will unblock extrom to write on it and clear it, after that extrom is mounted as Storage. clear.ink from startup is removed and last operation is to run Welcome screen.
To use it on any rom you need to unhide your extrom and run autorun.
RUU LOG
08:04:09 Connection with USB
08:05:57 Begin stage 1
08:06:27 CE Erase retry 1
08:07:08 CE Erase retry 2
08:07:48 CE Erase retry 3
himalaya screen : serial
v 1.03
when I update : error 112
AERO...Can you help me...please
or somebody....
I hope can use AERO ROM
aeroflyluby said:
Why not to install on \Storage ?
It's not removeable
Click to expand...
Click to collapse
sir aero, yes i can install apps on storage but those apps that needs to be installed on ram cannot be for instance spb mob shell... is there a way o increase ram size like in xda 2s?
thanks again..
jonrols said:
sir aero, yes i can install apps on storage but those apps that needs to be installed on ram cannot be for instance spb mob shell... is there a way o increase ram size like in xda 2s?
thanks again..
Click to expand...
Click to collapse
I can't really understand you. You got 108 free ram and I think you won't get any better