Pls. help. Bluetooth icon on my IIi taskbar(?) is gone;& as I tried to open it from Programs, it shows this:
"Bluetooth Radio failed to turn ON due to insufficient driver memory available. You must perform a normal reset before you can turn ON the Bluetooth Radio"
I did soft & hard resets but to no avail. Even with its current programs, Bluetooth was working well last time.
Pls. advise. Thank you
Related
Don´t know if any one can help me about this one:
when i use my wireless and stop it, i can not activate the bluetooth, error:
(The Bluetooth radio failed to turn On due to insufficient driver memory available.You must perform a normal reset before you can tur On the Bluetooth Radio.)
When i use just bluetooth without using my wireless no problem at all.
Helder Teixeira
Problem found!!! By some way, something to do with Omega One Battery Pack Pro. If i disable Omega, problem is solved. I´ve seen a post in clubimate relating with this (http://www.clubimate.com/forums/tm.asp?m=14268);(need login), Is there any one using omega? and also has that problem too??
Thanks ins advanced
Share your experiences...
Helder Teixeira.
Ok so I only use the bluetooth on my alpine to connect to my gps receiver, for TOMTOM use.
It has been working fine until last week, which happened to be a very hot day. TomTOm froze so i stopped the car and did a soft reset. When i opened up the bluetooth manager it came up with the error
"THe bluetooth radio failed to turn on due to insufficient driver memory available. You must perform a normal reset before you can turn ON the Bluetooth Radio"
So i do what it says and try a soft reset. Still same message.
I then turned the phone back on and left it for a few hours. It connected and all was well again!
Now iv just tried to use TOMTOM and the same error message is back.
so i reset and waited 2 mins before connecting.
It connected so i went into tomtom and it found me on the map and then froze.
Tomtom is version 5.21 latest and has been working great.
Please help what should i do?
Would a firmware upgrade help im currently on.
r1
g1337.39
d1.11.00
Where can i find the latest.
Many thanks in advance. Andy
The very hot day may have done it. If you have you GPS unit on the dash in direct sun, then the temp inside the unit may well exceed the maximum it can tolerate - they probably don't build the inexpensive units with high temp spec components.
Similarly - don't run your PDA under the same conditions - you may well damage the screen / internals (e.g. charging circuit) with over-temp.
HELP!!!! I try more patch, modify to registry... but I don't resolve this problem...
I have tried various ROM but all have the same error...
The last one rom installed is WM5 AKU3.5.2 R5 Rom Kitchen v2.
Many persons have this problem…
Someone is successful to resolve or has some idea?
Your are the only forum that can resolve this great enigma!!!
My solution, is to unflagged, when asks the wich port com choose, security check.
After this no more problem a no mare piaring to do.
Regards
The problem is not that one. However I have tried but it has not worked.
http://forum.xda-developers.com/showthread.php?t=304969
???Enigma???
I have tried the procedure here under:
1. BT off in Comm Manager
2. turn on BT headset
3. turn on GPS device
4. turn on BT in Comm manager
5. open TomTom 6 (wait some seconds and make sure it's connected)
6. go to phone and call myself (on the first call the headset is disconnected)
7. back to TomTom and make sure it works
Resolution of the problem is not one.
I have also the Himalaya that works with the Rom Wm2005… What is the problem?
It's possible to modify the registry in order to enable/disable Port COM???
I'm trying to connect my phone (ATT HTC Tilt) with a stereo bluetooth headset or trying to send files and everytime I scan for new devices it gives me an error stating "PROBLEM WITH BLUETOOTH HARDWARE"
Additionally, the "Turn on Bluetooth" option always turns off automatically....
What is going on? Can anyone help?
Please...
Anyone who experienced this or can give me a hand? Thanks!!
I had this same problem all of a a sudden on my Kaiser. But after doing a hard reset this got resolved.
And now i just flashed Dutty's 6.1 ROM. Its amazing update..
Cheers
Thanks Arun...
Tried the hard reset NO LUCK! Problem persists, and bluetooth keeps turning off. I go back to the wireless manager and check both boxes and they come back off in 30 seconds!!
When searching for devices it says (ERROR: PROBLEM WITH BLUETOOTH HARDWARE)
Not able to beam or receive files at all.
Any help? Thanks so much!!
Same Problem
Running into same problem here. I haven't even updated the ROM from stock yet, although I have done the JumpSPL step (cuz I received the white screen). My Radio is 1.27.14.09.
Any help is appreciated.
I would think that if you have done a hard reset and you don't install anything and you still have a problem then you **** is borked. time to do a warranty exchange.
has your bluetooth ever worked, with the rom that is currently on your phone?
Problem with Bluetooth Hardware!!!!
I am having the same problem. I have the stock AT&T ROM. Here is exactly what is happening:
The bluetooth is not working on my Tilt at all. It has lost connections with devices that it was already paired with (a Motorola Q Global and a headset). All attemps to pair the devices again lead to the following: "Error: Problem with Bluetooth Hardware".
When I go to Bluetooth Settings through the Comm Manager, then Mode and check "Turn on Bluetooth" and "Make this device visible to other devices", it unchecks as soon as I exit the settings menu. The Comm Manager constantly shows the bluetooth being off and when I tap the icon, the phone "thinks" for awhile and then it greys out again.
The only change that I have made from the time that it was working is to install the iphone package, and a today plugin (which I have since uninstalled) found here.
I recently changed my Kaiser Tweak bluetooth settings: I changed the BitPool from 'medium' to 'very high', but my headset was still working after that. The other settings are:
Sample Rate - 48000 (Advised)
Use Joint Stereo - Enabled (Default)
Receive Files - Enabled
Any ideas/suggestions?
Forced to do a hard reset
kcrumbley said:
I am having the same problem. I have the stock AT&T ROM. Here is exactly what is happening:
The bluetooth is not working on my Tilt at all. It has lost connections with devices that it was already paired with (a Motorola Q Global and a headset). All attemps to pair the devices again lead to the following: "Error: Problem with Bluetooth Hardware".
When I go to Bluetooth Settings through the Comm Manager, then Mode and check "Turn on Bluetooth" and "Make this device visible to other devices", it unchecks as soon as I exit the settings menu. The Comm Manager constantly shows the bluetooth being off and when I tap the icon, the phone "thinks" for awhile and then it greys out again.
The only change that I have made from the time that it was working is to install the iphone package, and a today plugin (which I have since uninstalled) found here.
I recently changed my Kaiser Tweak bluetooth settings: I changed the BitPool from 'medium' to 'very high', but my headset was still working after that. The other settings are:
Sample Rate - 48000 (Advised)
Use Joint Stereo - Enabled (Default)
Receive Files - Enabled
Any ideas/suggestions?
Click to expand...
Click to collapse
They only way to fix the problem was for me to do a hard reset.
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Edris said:
Hi All,
I just got a Jabra SP700 after pairing it with my Kaiser everything works fine ( making a call, receiving a call, Playing music through FM radio and TT navi. through the radio). The problem is when I disconnect the devices and turn them both on they will reconnect automatically but I can't hear anything through the SP700 ( FM Radio ). I will have to delete the device from the phone and pair it again in order to make it work.
Is there a better software for managing the bluetooth connections?
Open to any suggestions.
Thanks.
Click to expand...
Click to collapse
I have the same problem with my SP700 and my Tritton BT stereo headset.Phone calls work almost all the time through the SP700 speaker, but playing music or through the FM radio seems to be a problem. I can get them to pair up sometimes by only checking the Wireless Stereo box. It works for a few times, but then I have to delete and re-pair again.
I've searched for all over for answers, but nothing seems to be a permanent fix. It's very frustrating to use my devices for anything else but phone calls.
Just to add a bit of info, I do not have any problems with my old Motorola HS820. Of course, I'm not using SP700.
Hope that helps your troubleshooting.
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Possible solution
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Edris said:
Found a solution that works for me!
First of all thanks guys for the suggestions !
I think SP700 works fine ( GREAT! ) but the issue is with the A2DP. I found out that A2DP turns on the first time after pairing the devices but it does not turn off. So the next time you pair the devices it is turned on and won't accept the new connection. So what I tried to do was after connecting I turned off A2DP and turned it back on and it works fine.
Suggestion
Search for A2DP Toggle, install it and after pairing the devices if it doesn't work just turn A2DP off and back on.
I assigned the 6th hardware button on my Kaiser (PTT Button) to A2DP Toggle that way I can have access to it all the time.
Works great.
Click to expand...
Click to collapse
Thanks! Nice App! Tried it with my Tritton BT stereo headset and it works! Had to install to my device instead of Storage card, then had to delete and re-pair, but it so far I can toggle between on and off Stereo Headphones without any problem. Will try on my SP700 shortly.
I attached the Cab if anyone else wants it.
Thank you!
Works with SP 700!!!!!
Mal Bridgeman said:
I have exactly the same problem with hte SP700 connecting to a Touch HD.
I notice there is a software upgrade for the SP700 on the Jabra site but I can't get to apply it because I lack a driver to allow the PC to recognise the JAbra SP 700.
Any ideas would be greatly appreciated.
Thanks
Mal
Click to expand...
Click to collapse
When the software loads, follow the instructions, do not install with any of the microsoft wizards that pop up, it will install itself. I couldn't find anything that lists what changes that were made.
SP700 Firmware
FYI,
I too had the same issues and downloaded the sp700 firmware update. I thought the same thing about the drivers, but called Jabra and they told me the firmware update has the drivers embedded in it. When you start the install you cannot plug it in till it tells you to. After you plug it in it installs the drivers. But BEWARE I have not been able to complete the upgrade, it stopped halfway and bricked. I called support and they said there is nothing to do, but luckily I bought it from Costco and they returned it. So being not so bright I tried it again but on a different computer (thinking that there might be a conflict) and it didn't even load and bricked it again. So I returned it yet again. So then I gave up on Jabra support and found A2DP toggle. It works good enough, so I am leaving it at that....
Take Care
David
Tilt WM6.1
andrew-in-woking said:
Hi
I have had similar problems with the SP700. I was using the Hyperdragon III before the current ROM (in signature). With my old ROM I found that the following method worked:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable mode on the phone
4) The device then automatically connects over both Hands Free and Wireless Stereo protocols
5) Turn discoverable off
Now that I have the Hyperdragon IV ROM I notice slightly different behaviour:
1) Turn on the SP700
2) Wait for it to make one low tone
3) Turn bluetooth onto discoverable on the phone
4) The device then automatically connects over hands free protocol
5) Go into bluetooth settings on the phone then the devices tab and manually connect by selecting "Set as Wireless Stereo" from the pop up context menu- this connects over the wireless stereo protocol
6) Turn discoverable off
One thing I do find very annoying about the SP700 is that it disconnects from the Wireless Stereo protocol after a phone call is ended. When this happens I have to manually re-connect it by pushing the button on the SP700 until it peeps.
I too would value a software upgrade for the SP700. I just get the feeling that it has somehow shipped with a beta or incomplete firmware. If anybody knows how to do the firmware upgrade please share this.
Thanks
andrew-in-woking
Click to expand...
Click to collapse
I have the exact problem that you are having with the new, Hyperdragon IV, ROM.
Is this A2DP Toggle really the only way - I mean what's the difference between pressing a button on my Kaiser to reconnect and pressing the button on the SP700 ??
I have tried using Mortscript as shown http://forum.xda-developers.com/showthread.php?t=382172&highlight=a2dp&page=2 Although I edited the end out because it kills the player after ending a call. This hasn't helped either
I am off to see if the same problems occur with my lady's N96. If not and no good solution can be found for this I may have got her a new present.
Aren't I nice ?!
Found another possible solution, it,s called zoA2DP. So far it works flawlessly between my SP700 & stereo headset without having to toggle anything or change any settings. When you install it, delete your original pairings and add them again, make sure that hands free & wireless stereo are checked in advanced options on you BT settings. I believe this is a registry mod, there are no icons or any noticeable applications running in the backround.
The thread is here
http://forum.xda-developers.com/showthread.php?t=279127
Cab file attached