I just got a replacement G1 from Tmobile, for free bless their hearts, cause my headset is going to the crapper. I'm trying to update my raido to the 2_22_19_26I, as I did before with my first G1, so I can install the DangerSPL. I have tried with the stock recovery, Cyan's 1.4, and Amon-RA's 1.5.2 to install it, and each time, it goes about the update process as normal, asks me to reboot, I see the picture of the chip and then it takes me back to recovery.
Each time, though, I'm still at the 1_22_12_29. I check by turning on the phone, then Settings --> About Phone, and also by going into the SPL, still at the 1.
Any ideas?
EDIT: also I'm using the radio on HTC's developer website, so it's legit.
Uh, i'm not XDA police but i'm pretty sure this goes in Q&A.
You need a custom recovery before you can even upgrade the radio but are you on 1.5 doing the one-click?
One-click:
http://theunlockr.com/2009/08/22/how-to-root-the-mytouch-3g-or-g1-in-one-click/
"I have tried with the stock recovery, Cyan's 1.4, and Amon-RA's 1.5.2"
I've tried with many different recovery's.
jordancrockett said:
"I have tried with the stock recovery, Cyan's 1.4, and Amon-RA's 1.5.2"
I've tried with many different recovery's.
Click to expand...
Click to collapse
When your in rec mode you must flash the radio while there, i heard the rec gets deleted if you dont update the radio when you install a recovery.
rec mode? please restate what you just said.
jordancrockett said:
rec mode? please restate what you just said.
Click to expand...
Click to collapse
rec=recovery mode
The guide says flash the radio while your in recovery mode not after.
i've done the recommended one-click method, even went back and let my phone update itself back up to stock, but i still have radio 1.
jordancrockett said:
i've done the recommended one-click method, even went back and let my phone update itself back up to stock, but i still have radio 1.
Click to expand...
Click to collapse
Can you load roms since you said you tried recoveries?
I can load everything, ROM's, SPL's, different recoveries, boot.img's.
I've tried updating the radio before I upgrade the SPL, after, with a stock recovery, or with Amon-RA's/Cyanogens. I don't know why it's not working.
jordancrockett said:
I can load everything, ROM's, SPL's, different recoveries, boot.img's.
I've tried updating the radio before I upgrade the SPL, after, with a stock recovery, or with Amon-RA's/Cyanogens. I don't know why it's not working.
Click to expand...
Click to collapse
Donut roms(1.6) dont need the Haykuro or Hard SPL you can load roms with the one you have now.If you want to use hero or eclair then you'll need the radio and SPL.
Also if the radio is anything like the spl, don't use the trackball while flashing it
Another user and I, have this same issue with no solution, we have threads in dream q&a and dream general. I also used recovery flasher to gain root when I was on cupcake. My radio is older than yours though =/ if you can't find the threads ill post the links tmw, as I'm abt to sleep now..good luck hopefully we can all find a solution, or at least identify the source of the problem..
not sure if this will be of much help, but you can always try to revert back to the stock firmware using the dreaimg.nbh file and stock spl.
i had a friend who, like with your radio, couldn't flash the more recent custom recoveries.
whatever the reason was, i suggested that he just "unroot" and go back to android 1.0, stock spl, stock radio , whatever, and just re-root from there
phamous said:
not sure if this will be of much help, but you can always try to revert back to the stock firmware using the dreaimg.nbh file and stock spl.
i had a friend who, like with your radio, couldn't flash the more recent custom recoveries.
whatever the reason was, i suggested that he just "unroot" and go back to android 1.0, stock spl, stock radio , whatever, and just re-root from there
Click to expand...
Click to collapse
ust make sure when unroot you follow the instructions...somehow i bricked my first G1 when I was unrooting. Dont ask me how I did that but I did ha
thenameismax said:
just make sure when unroot you follow the instructions...somehow i bricked my first G1 when I was unrooting. Dont ask me how I did that but I did ha
Click to expand...
Click to collapse
haha, good point! when in doubt, just follow the guide!
this one, if you don't already have it,
http://forum.xda-developers.com/showthread.php?t=442480
shows you how to "downgrade/un-root" your device.
happy flashing!
I apologize to sound rude, but I've been with XDA and the G1 rooting community since 1.0. I know these are good, helping tips and guides, but I've tried to explain that I've done everything like that already, gone back to stock, gone up to cyan's 4.2.13, gone back to stock, then up to a stock 1.6, even with the stock updates, when it says writing radio, radio doesn't update.
your replies are appreciated, just not really relevant or helpful.
I was setting up a friends g1 and same thing, he got the phone from warranty exchange and I was able to downgrade, gain root, change recovery image and flash enom's rom with no issue. But upon boot up I saw his radio image was .29 and tried to update the radio. I kept getting something like "line 2: getting prop(device = dream)"
So I started all over rc29, root, recovery image and every time I try to update radio, same issue. Even when use Cyan's method and try the developer's image with radio update, it fails.
In the end, since enom's rom can use any radio, he was ok with it. But really i wanted to get his g1 on the latest radio image. I feel your pain as I researched the errors as well and couldn't find anything. Good luck.
Fabe
mdafabe said:
I was setting up a friends g1 and same thing, he got the phone from warranty exchange and I was able to downgrade, gain root, change recovery image and flash enom's rom with no issue. But upon boot up I saw his radio image was .29 and tried to update the radio. I kept getting something like "line 2: getting prop(device = dream)"
So I started all over rc29, root, recovery image and every time I try to update radio, same issue. Even when use Cyan's method and try the developer's image with radio update, it fails.
In the end, since enom's rom can use any radio, he was ok with it. But really i wanted to get his g1 on the latest radio image. I feel your pain as I researched the errors as well and couldn't find anything. Good luck.
Fabe
Click to expand...
Click to collapse
Yeah, that's exactly what I'm going through, except it's not throwing up any errors or anything. it updates, says "writing radio image...", reboots with the HTC symbol, and goes back to Recovery and Formats the CACHE like always. *sigh* maybe T-mobile found a way to mess with us after all?
Just a question, when u rooted, did u do it the old way or new way. And by old way that I used, was the DREAIMG.nbh, then on home screen the type cd /sdcard blah blah...
Related
First of all forgive me if this question as been asked a million times but to be honest I'm finding the Dream section a mess.
Now onto my question.... I've rooted my G1 and I'm currently running JF 1.51 with hero skin, now I'm I correct that I will always be rooted as long as I stick to custom roms?
The other thing is when I go into recovery mode I get a message at the top of the screen something like "Unable to find /system/command/recovery.cmd" am I correct that means I'm unable to proform backups? which is no big deal for me.
Finally whats the deal with this new spl, do I really need it to run a hero ported rom? I only ask because in all my years flashing windows phones the spl is something you should flash once and leave alone to avoid errors that can brick your phone.
Yes you will always be rooted. Not really sure on the recovery thing...You might want to try to fix that by flashing another recovery image. Yes you need the new spl to run the hero ROM since its HUGE
alritewhadeva said:
Yes you will always be rooted. Not really sure on the recovery thing...You might want to try to fix that by flashing another recovery image. Yes you need the new spl to run the hero ROM since its HUGE
Click to expand...
Click to collapse
Thanks for the fast reply, as for the recovery thing like I said I would never back anything up and restore it anyway (I've always started afresh with every new rom)
Now going back to the spl thing.... Ive already updated my radio to the latest so when I do finally go for a hero rom and do flash my spl is the new spl a custom one which will allow me to reflash back down to a non-hero rom? or do I have to go back to the orginal hardspl first?
The new SPL was released by haykuro and it allows you to have about 30 more mb of space on your system partition. It still allows you to flash non-hero ROMs as well as hero ROMs. Sorry for the slow response >.>
Thanks alritewhadeva everything is clearer now.
It seems that I can't get a clean boot off anything other than the JF 1.5 or 1.51 US builds. I've tried cyanogen and even jf 1.51/1.5 ADP builds but it always boot loops. Any suggestions?
I've read through the questions threads, I've used search. I just can't seem to find anything relevant to my problem in specific. I've flashed to hardspl, I've updated the radio, tried various builds of the same developer to see what it could possibly be, but I'm pretty stumped.
Hmmmm... try re-flashing RC29, re-root, and try the update again... sounds like its not updating correctly
Tried that multiple times over the last few days. this time, I managed to get past a straight reboot loop, but I was stuck at the boot screen with sounds/alerts/sleepbutton as if I had changed my launcher.apk with a file from the wrong rom. Going to reflash to 29 again and try it again =P
As many times as I go through this long (well, not quite) and arduous (heh, sure) process, it's still fun
*edit* out of curiosity, how extensive are nandroid backups? I've tried some flashes using a nandroid restore from an rc29 with the OTA radio and cyanogen's restore img. Would that reflash me back to prior settings?
//Note not all of my installs are with nandroid restores. I have tried with pure fresh dreaimg.nbh/root/hardspl/radio installs.
hmmm, have you tried flashing the new recovery? Try Cyan's 1.3.1 Recovery Image, might work a little better.
just reboot looped again. order of operations for a freshie should be something like this;
1)dreaimg.nbh
2)root
3)cyan's recovery
4)ota radio
5)JF 1.51 ADP
correct?
*edit* in all honesty, I want to try cyan's newest build but if I can't even get past installing JF's ADP build... ya...
wahookasan said:
just reboot looped again. order of operations for a freshie should be something like this;
1)dreaimg.nbh
2)root
3)cyan's recovery
4)ota radio
5)JF 1.51 ADP
correct?
Click to expand...
Click to collapse
No... you're missing HardSPL between root and cyan's recovery.
lol, just did some more searching, and realized that I was misunderstanding what hardspl actually did for me. It was my understanding that Cyan's recovery img replaced hardspl (don't ask me how I got it mixed up, I just did, ok? xD). I just got into rooting my G1 recently, if you haven't noticed.
Thank you for your timely reply's and hopefully this helps me dive into what I was missing out on
Sorry for the double post but the issue isn't resolved.
the problem is persistant. even with hardspl in (could have sworn I had that in at some point anyway) I still can't use the ADP or cyan's latest
Did you perform a wipe before flashing ROMs? Not wiping may cause some boot loops with certain mods.
I've done a full wipe back to dreaimg.nbh (assuming that's what you mean). I've gone back to step 1 of the root process. Still no go
wahookasan said:
I've done a full wipe back to dreaimg.nbh (assuming that's what you mean). I've gone back to step 1 of the root process. Still no go
Click to expand...
Click to collapse
You should go ahead and wipe before all of the builds when your starting up. I believe DREAIMG.nbh is a US based rom, and the JF you are installing is ADP. You MUST wipe when switching from US based ROM to an ADP based ROM
im having the exact same problem i was able to get a rom other than the JF installed, i have tryed every damn way possible and mine will not work either. i use the Haykuro 1.5 Cupcake one, and it seems to work. My phone gets stuck whenever i try to load any hero, or Cynanogen roms. Its depressing, yeah fun at first but now i look at posts and cry hahahahha when these people have theres all bad ass! SOMEONE HELP USSS! email me at [email protected] if needed pleeeease i need HERO!
root, wipe, flash JF, wipe, update radio, wipe, update recovery image, wipe, flash whatever ROM you want.
Did you try that?
...It's pretty much been over half a year since I needed to root my phone again, but I just received a brand new one from tmob.
SO. I did the root deal, that went super smooth, I have JF1.51 CRB43 ADP to start with.
NOW, I am trying to update the radio, and it does not seem to be working. From what I remember and what I've read, all you do is flash it like you would any rom, rename to update.zip and recov alt+s, right? Well, when I check the radio version it still says the original, not what I flashed. So I re-downloaded and tried again, no luck.
....feel like a real idiot here haha, never had it not work before. Tried searching but I had no luck finding the solution. By all means if you have a link and this was a pointless post just tell me, else I just need some help!
which recovery image do you have installed
maruutah said:
...It's pretty much been over half a year since I needed to root my phone again, but I just received a brand new one from tmob.
SO. I did the root deal, that went super smooth, I have JF1.51 CRB43 ADP to start with.
NOW, I am trying to update the radio, and it does not seem to be working. From what I remember and what I've read, all you do is flash it like you would any rom, rename to update.zip and recov alt+s, right? Well, when I check the radio version it still says the original, not what I flashed. So I re-downloaded and tried again, no luck.
....feel like a real idiot here haha, never had it not work before. Tried searching but I had no luck finding the solution. By all means if you have a link and this was a pointless post just tell me, else I just need some help!
Click to expand...
Click to collapse
If your using Cyanogen's recovery, try to physically press the alt-s, and home + back to reboot
I believe it works like that for flashing the IPL (radio) and SPL
where did you get the radio from?
Sorry I left out the recov info, I know my signature is misleading...didn't change it yet..!
I'm using JF 1.43 recov, I remember that (not sure if it was ever fixed, all I know is that flashing the SPL with CM recov caused 'error at line ___' when flashing new roms) that you cannot flash the new SPL with cyanogen recovery, so I'm using JF's until I get the radio and spl flashed correctly.
I got the radio from where I usually have in the past, as well as the new SPL
http://sapphire-port-dream.googlecode.com/files/
(Of course I will not flash the latest SPL until the newest radio is flashed first!)
I just want my happy CM 3.9.7 back..! With the ability to flash the new hero roms when I get curious..
****I am now attempting to flash the radio with cm recov 1.4, will update on this if it works.
****no luck with cm either, didn't think it would make a difference but thought I would give it a shot. I still have 1.22.12.29 for my radio :/ agh!
So...Still can't update the radio for whatever reason, just does not take, and I still can't find anything in the forums about this either... :/ Anyone have any ideas at all?
get the radio from the htc website maybe you got a bad download. i have flashed radio and new spl with cyanogens recovery so i know it will do it. after flashing the radio press home and back to reboot. do not reboot from the recovery console because i have noticed that it will not write the image.
david1171 said:
get the radio from the htc website maybe you got a bad download. i have flashed radio and new spl with cyanogens recovery so i know it will do it. after flashing the radio press home and back to reboot. do not reboot from the recovery console because i have noticed that it will not write the image.
Click to expand...
Click to collapse
Thanks for the link ^-^ I will give it a shot. Good to her that the CM recov flashes the new SPL alright now..! I will post results...every time I flash it goes through the motions of writing the radio but just never shows that I have the new one..super frustrating.
** I also notice that whenever I have tried to flash the radio on the new phone, when I reboot it goes through the appropriate motions, yes, however it puts me back into recovery every time. I wonder if I should just completely start over (unroot, re-root) hope thats not the case..I just got it all set back up again :/
Nope, no matter where I download from and how many times I flash with different recoveries.. I still have the original radio 1.22.12.29 :/
This has always been so easy! I've never had issues with rooting, then updating the radio, then updating to the new SPL.. :/
maruutah said:
Thanks for the link ^-^ I will give it a shot. Good to her that the CM recov flashes the new SPL alright now..! I will post results...every time I flash it goes through the motions of writing the radio but just never shows that I have the new one..super frustrating.
** I also notice that whenever I have tried to flash the radio on the new phone, when I reboot it goes through the appropriate motions, yes, however it puts me back into recovery every time. I wonder if I should just completely start over (unroot, re-root) hope thats not the case..I just got it all set back up again :/
Click to expand...
Click to collapse
If you can, try rerooting, it will only be a few more steps.
B-man007 said:
If you ca try rerooting, it will only be a few more steps.
Click to expand...
Click to collapse
Yeah, I was hoping to not have to but I will in a bit here if I still can't figure it out. I have root just fine, running CM 3.9.9.1 even, which I usually only run his roms, however I do like to try the Hero roms as well as they come out..
bummer :/
maruutah said:
Yeah, I was hoping to not have to but I will in a bit here if I still can't figure it out. I have root just fine, running CM 3.9.9.1 even, which I usually only run his roms, however I do like to try the Hero roms as well as they come out..
bummer :/
Click to expand...
Click to collapse
I don't know why its not updating your radio, but everything else works fine. You should update the radio before updating to cupcake builds. maybe that will help?
gave up for a while, finally re-rooted
Re-rooted and still cannot update my radio, I have tried updating it after the very first rooting steps, after updating to JF RC33 as well, I still can't get the latest radio to get onto my phone. I have tried with JF recovery, CM recovery, as well as the original recovery image, and nothing. Notta. Zip. No idea why my phone simply will not take the new radio image.. I have re-downloaded it a million times as well, going in circles..don't get why the phone will let me root, unroot, all that jazz, and simply will not let me update the radio... driving me nuts!! I can use CM roms just fine of course but any other roms I am stuck with not trying cause of this annoyance!! Anything anyone can recommend would be great
o man still can't get it to work?
try flashing the official 1.5 OTA update, which contains the updated radio. see if it gives you an error message. if it does, take it to tmobile and tell them to replace your phone.
if it flashes...see if it updated your radio. if it did, you can use the one click root to root your phone
Thanks again buddy, I will try it out ^^
So, I unrooted, and applied the OTA updates from 29 to 30, 30 to 33, 33 to cupcake..and I still don't have the latest radio, still at 1.22.12.29. I got the ota cupcake here:
https://android.clients.google.com/updates/partner/signed-kila-ota-150275.53dde318.zip
i'm going to try flashing the ota radio update without root if it will let me..grr..this is so weird, there is no reason why it shouldn't take a simple radio update..hrm
***attempted the ota radio update, guess you can't without root which is what I figured, but frick, this makes no sense.. >>
so, this is a bit odd, at http://developer.htc.com/adp.html, one of the spots to DL the latest radio, when you hover over the radio link for 1.5 and 1.6, it says "ota-radio-1_22_14_11.zip" rather than "ota-radio-2_22_19_26I.zip", weird, eh? Wonder if it's simply not the right radio, and labeled wrong, I have no idea, but this is getting super old.
I'm actually having the same problem, can't seem to update the radio with the radio image the htc site provides. It's still stuck at 1.22.12.29
Anyone had this before? Any help would be appreciated
I can't get around it, and it's really frustrating, since the only rom I can use is a CM build..aside from a couple others, but CM is the best as far as universal SPL use goes..
So what I've tried so far:
- Updated to HardSPL
- Tried multiple Radio updates, new ones, old ones, even some from the forums.
- Tried a few complete updates that include the radio image
- Tried flashing directly from fastboot, not sure what partition I need to flash though, the radio partition gives me an error that it does not exist.
Still no go. The weird thing is that I come from a stock 1.5 installation updated from 1.0 via t-mobile. And I'm still at the original 1.0 radio image.
Ok I've done the 1 Click Root process. The problem is, I totally UNrooted my phone before I did the 1 click root. I tried to load a Hero rom I got off the www.theunlockr.com website but I had to update the SPL which bricked my phone. I did wipe first so thats not the problem. I don't know what went wrong when I bricked my phone. I am getting a new from t-mobile(I kinda told them the donut 1.6 update screwed my phone up).
Now I want to root again with the 1 click but do I need to go back to the original build RC29 build or whatever it was in order to root with the 1 click ? And when I flash to a new rom do I need to update the SPL again?
READ FIRST!! I dont know where so search. I dont feel like finding you all the guides warnings and post about it. There are many precautions to take while flashing hero and even if you follow all of them to the "T" you still have a big chance of bricking your phone so use the Search Bar
nickryan0612 said:
READ FIRST!! I dont know where so search. I dont feel like finding you all the guides warnings and post about it. There are many precautions to take while flashing hero and even if you follow all of them to the "T" you still have a big chance of bricking your phone so use the Search Bar
Click to expand...
Click to collapse
The thing is I've flashed all sorts of rom's before, but I wanted to try the 1 click rooting process. I think what happened is I flashed the SPL before I flashed the updated radio. I was doing some research on the whole thing. I flashed the SPL first.
if you use the DREAIMG.nbh to go back to rc-29, it is really easier to use the telnet commands then it is to root with the one click imo, you can use one-click root, but you have to find the newer version of the recovery flasher, and if you use it and don't flash a custom rom, then the system will overwrite the custom recovery image with the stock one. if you use the telnet commands then you will overwrite the stock recovery image with a custom one, so the telnet commands are more stable
to update your spl, make sure you have a pvt board in bootloader (camera and power) and that your radio is 2.22.19.26I (make sure you have that radio, not just assume after you flash it) then you can get rid of all the user error in flashing the 1.33.2005 SPL.
xOneSainTx said:
The thing is I've flashed all sorts of rom's before, but I wanted to try the 1 click rooting process. I think what happened is I flashed the SPL before I flashed the updated radio. I was doing some research on the whole thing. I flashed the SPL first.
Click to expand...
Click to collapse
Were you already rooted when you did the 1 click root? - if you were then that might have been were the mess up happened because once you do the one click root you have to flash a rom (probabably cyanogen would be best) to continue or you lose root.
Following that question if you were already rooted and had hard spl and new radio - the one click might have cause you to lose that.
You have to flash from hard spl to danger spl
Radio should be newest or second to newest
Also it is said to flash hero rom right after flashing spl. - Which means not turning off your phone or rebooting after flashing
- I saw a video were they were at the rainbow boot screen and they flashed the Danger Spl and then inserted a new sd card that had hero and flashed it without rebooting.
Read up more on this
is one click still ok ?
I've had my G1 for about a yr now. Watching the mods grow . Never had thought about rooting just because I didn't want to have to keep changing to keep up to date. Then the one click came out and it was time. Ordered my 8gig class6 sd and before I got it Google did this C&D to CY. I see people saying they are doing the 1 click method and the links they put on are before the C&D. Can it still work ? Also everyone who tries to give directions how to get root and roms are different. Even this thread has been changed or something was left out. Is there a true one click method ? I tried theUnlockr way 3 times and I still wound upwith a wiped phone. Please Help Me ...
nPHILLY said:
I've had my G1 for about a yr now. Watching the mods grow . Never had thought about rooting just because I didn't want to have to keep changing to keep up to date. Then the one click came out and it was time. Ordered my 8gig class6 sd and before I got it Google did this C&D to CY. I see people saying they are doing the 1 click method and the links they put on are before the C&D. Can it still work ? Also everyone who tries to give directions how to get root and roms are different. Even this thread has been changed or something was left out. Is there a true one click method ? I tried theUnlockr way 3 times and I still wound upwith a wiped phone. Please Help Me ...
Click to expand...
Click to collapse
one click will not work in donut 1.6. it will be patched, there is a thorough guide in my sig. i also have links i can give you for cm 4.0.4 and 4.1.11.1 if you want them.
1-click root only works with CRC1 and lower. Personally, I prefer to downgrade to RC29 and manually root it. I've done it about 20 times that way and have never once had an issue. In fact, I did it last night and today that way and both phones are rooted with Hero ROMs and running perfectly.
My advice, find a good tutorial (there are plenty, particularly the stickies on XDA on the subject) and download all necessary files ahead of time so that you aren't stuck in the middle of rooting looking for a file. If you want to flash the update "Danger" SPL, there is a combination radio/spl so that bricking is less likely. Search XDA for it. Also, check if you have PVT board first (camera+power). If not, brick it you will (or more than likely will). If I had to guess the main reason for problems and bricks it is that people rush the process and skip steps because they started the process without reading the whole tutorial.
nickryan0612 said:
Were you already rooted when you did the 1 click root? - if you were then that might have been were the mess up happened because once you do the one click root you have to flash a rom (probabably cyanogen would be best) to continue or you lose root.
Following that question if you were already rooted and had hard spl and new radio - the one click might have cause you to lose that.
You have to flash from hard spl to danger spl
Radio should be newest or second to newest
Also it is said to flash hero rom right after flashing spl. - Which means not turning off your phone or rebooting after flashing
- I saw a video were they were at the rainbow boot screen and they flashed the Danger Spl and then inserted a new sd card that had hero and flashed it without rebooting.
Read up more on this
Click to expand...
Click to collapse
I was rooted before I did the one click but I downgraded to RC29 with DREAIMG.nbh file. I did the 1 click process fine. I figured that what fxcked up my phone is that i flashed the custom SPL before I flashed the new radio first. I'm pretty sure thats what messed it up. I wanted to the Amon Ra's Recovery image and I didn't know how install that with out doing the 1 click root process.
ya if you flash spl before raidio that's what messed you up ! always radio first then spl . but you know that now .can you get in recovery at all ?
lucky 69 said:
ya if you flash spl before raidio that's what messed you up ! always radio first then spl . but you know that now .can you get in recovery at all ?
Click to expand...
Click to collapse
No I can't get passed the G1 boot screen. Its ok though T-Mo is sending me a "LIKE NEW" G1. I told them the donut update screwed my phone up. I can't believe I did the SPL first but its a mistake that could have cost me more then a 19.95 delivery fee that IS being waived by T-Mo.
But heres the question with 1 click root do I need to downgrade to RC29 or no?
xOneSainTx said:
No I can't get passed the G1 boot screen. Its ok though T-Mo is sending me a "LIKE NEW" G1. I told them the donut update screwed my phone up. I can't believe I did the SPL first but its a mistake that could have cost me more then a 19.95 delivery fee that IS being waived by T-Mo.
But heres the question with 1 click root do I need to downgrade to RC29 or no?
Click to expand...
Click to collapse
no just be on stock cupcake and use the 1 click root. Then when you did that go into recovery and flash a rom that is not hero or requires danger spl
nickryan0612 said:
no just be on stock cupcake and use the 1 click root. Then when you did that go into recovery and flash a rom that is not hero or requires danger spl
Click to expand...
Click to collapse
Sounds good. Before screwing things up I always had good success in flashing roms trying multiple roms in a day. My favorite is the xRom. I am curious to see if eventually there will be a Cliq rom.
I have been trying to flash the CM7 Rom to my G1 and continue to get the same error messages... I tried uploading a pic but the app wouldn't let me, so I will try and get the pic posted asap
Sent from my LG-P999 using XDA App
what is your radio/spl?
also have you flashed many other roms before?
Please using following combination for Radio and SPL. Also note, flash radio first and then SPL otherwise G1 will not boot. Also make sure you have Clockworkmod recovery for CM7. This recovery helps for smooth flashing for CM7.
update_2.22.28.25_S - Radio
hboot0013d-signed - SPL
kudlinux said:
Please using following combination for Radio and SPL. Also note, flash radio first and then SPL otherwise G1 will not boot. Also make sure you have Clockworkmod recovery for CM7. This recovery helps for smooth flashing for CM7.
update_2.22.28.25_S - Radio
hboot0013d-signed - SPL
Click to expand...
Click to collapse
OK, this might be sorta a strange question, but this looks to be the best place to ask it.
Will the Dream be bootable if you flash only the Radio and SPL, leaving untouched the stock Android 1.6?
While I am a Linux geek, I am new to android and prefer to take things one step at a time. That explains why I have a Rooted dream with Amon RA with the stock 1.6 backed up with nandroid.
TheLexx said:
OK, this might be sorta a strange question, but this looks to be the best place to ask it.
Will the Dream be bootable if you flash only the Radio and SPL, leaving untouched the stock Android 1.6?
While I am a Linux geek, I am new to android and prefer to take things one step at a time. That explains why I have a Rooted dream with Amon RA with the stock 1.6 backed up with nandroid.
Click to expand...
Click to collapse
never tried, theoretically it should be as if you did a factory reset and you would just use your recovery to replace anything lost. but if you want to be safe maybe someone who has will chime in.
besides the point go ahead and flash a new rom, even if you stick with 1.6 firmware the developers have come out with much superior roms over the stock android. if you want only 1.6 try super d or super csdi
ok so i decided to test this out, updating a g1 to the 2708+ radio/spl and not flashing a new rom -------- stuck on g1 boot screen, hit call+menu+power then hit home to reboot to recovery, reflashed rom and gapps, rebooted, now everything is good as can be, so to answer your question --- yes it appears you need to flash a rom after you update your radio/spl