Related
hi, new member here.
bought my tilt on 10/4/07. has been flawless since that time.
used the nav quite a bit during a road trip, used a cig lighter usb charger.
got home and my battery was at roughly 40%.
put it on the charger at night went to sleep. in morning disconnected it at 8 am. shortly after i arrived at work i got the critical battery low chime. checked and it had like 7% battery life.
figured i didnt plug it in right, or it got knocked loose some how and didnt get charged.
put it in flight mode to minimize battery usage. left work at 2 30 pm (4% battery life) and put it on the car charger. got home and put it on the HTC supplied wall charger. light turned amber, so i assumed it was charging.
checked an hour later and turned phone on, it said 0%, and immediately died. left it on the charger for a few hours and the light was still amber, turned it back on and again 0% and phone immediately died and did a soft reset on its own. i turned the phone off and left it on the ac charger, took out the sim card and put it in an old blackberry to use while the battery was charging.
its been on the ac wall charger for the last several hours, i checked and the phone is totally dead, cannot turn it on, and the LED at the top is now RED.
what is the problem here? why wont this thing charge?
thanks in advance, i have alot of critical info on this device and any help would be greatly appreciated.
i cannot hard reset because i cannot turn the flippign thing on....
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
I'd try a different charger first. If that makes no difference then a different battery. If that still does not make any difference then time to exchange it.
Lidberg said:
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
Click to expand...
Click to collapse
connected to either the computer or the wall charger, the LED thats normally amber when charging, and green when charged, remains red.
I had something very similar happen to my wizard.
And as weird as it sounds, the only fix was to charge the battery in a friends wizard on his charger. I'd check the battery if possible.
Could be the battery. Know any place or anyone that will let you try a charged battery? If not, you might have to go in to an AT&T store.
i think i got it working. did some reading/browsing...
took a usb wire and cut the mini usb head off. dissected it and found the the red and black charging wires. took out the battery and held the leads to teh battery while the other end was plugged into a USB/AC adapter wall charger from a old blackberry. after manually charging the battery for several minutes, i put the battery back in the phone and the phone started up. now it seems to be charging off the wall charger and the led is now amber from red.
thanks for all your help/suggestions.
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
tiltyoself said:
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
Click to expand...
Click to collapse
Repeat this proceedure but this time do not turn the phone on, just plug it in to the wall charger once you have zapped the battery again.
Turning your phone on probably just caused the already recovering battery to die whiles it is trying to take on a charge.
It is mentioned quite a lot on the boards that Li-Ion Batteries do not like being over disscharged and there is usually a little protection circuit in the battery to provent complete disscharging although this circuit may be on board the phone. Completely disscharging a Li-Ion cell will kill it stone dead and it will need replacing.
When you took the battery out and so called jump started it with your flying leads, this possibly reset the little protection circuit in the battery so it can now take on a charge. I feel that once you turned on the phone, this was to much for the already depleted cell to take and possibly re-tripped its inbuilt circuit.
If you do manage to recover you cell, in future it is good practice not to let the battery go below about 25%. Li-ion cells are generally happy being top off regularly.
I hope this helps buddy
Do let us know!
Cheers
C.
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
That Sucks! I hope they'll give you a new battery.
tiltyoself said:
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
Click to expand...
Click to collapse
I had exactly the same problem with my battery. It came on though after a day. Although the battery life after this happened went down to 10hrs max on standby. I sent the phone back and got a new one and now all is fine.
This is a problem that affects almost all makes of phone. There are three (main) causes of the problem:
1.
The battery charge drops too low to allow the charging circuit to recognise a battery is even in place (red no charge light stays lit)
possible solution:
http://forum.xda-developers.com/show...22&postcount=6
(in the end very similar in the end to the USB wire used in post above)
2.
A faulty battery (but if you can charge it using a cut usb cable or using a couple of AA batteries this may not be a faulty battery.
3.
A faulty charger OR a charger not delivering 5v at 1000mA as the OEM one does. Many chargers that are used for other phones or generic chargers only deliver 500mA. This is not enough when your battery drops very low. (these chargers are OK for occasional use but I do not advise using them regularly particularly if the no-charge syndrome has shown itself)
4.
A faulty USB connection on the phone. I have now seen a couple of reports where the fine wire connections in the phones USB port have become bent out of place.
Number 4 above is at least possible for the OP as it seems the battery will charge using a cut USB cable but not when either the PC USB cable or mains charger is connected. A USB port on the phone with a a bent internal contact would explain what's happening.
A previous poster was able with a needle or similar to bend the contact back into place.
Mike
i had the same problem with my phone.
put it in the charger overnight and woke up in the morning and couldnt turn on the phone with blinking red light. I don't know if my battery was over-drained though. I went to AT&T and was playing around with their charger and new battery and somehow the so-called dead battery started working again. They changed the SIM card on my phone there and then i haven't been able to use the phone since. I've changed the network to GSM instead of Auto setting under Phone Options which allows us to make calls; but now I can't connect to 3G network.
Charging thru mini usb
My phone started to exhibit similar problems...plugged in but no charging of the battery. I finally realized that my mini usb connection on the phone has been compromised (bent, distorted=not functioning properly) Now I have to prop the mini usb connection up at a slight angle to engage the charge. I think the plastic/metallic connector on the phone is somewhat fragile ...I had similar issues with my hermes.
called customer support.
they are sending me a new phone and battery.
how do i know its not a refurbished one? any clues?
before u send out your defect phone, have u check if your phone's mini-USB connector has bent or misaligned pins?
yeah all the connectors visually are fine.
okay so this is a new problem... if I plug my tilt in to my car charger, the battery actually drains faster than if it's unplugged... about a percentage a minute... when I come home and plug it... it charges regularly. I've tried 2 different roms, 3 different radios and 2 different car chargers... any ideas? been doing a lot of soft resets lately, wondering if that would burn the battery out?
new revelation!
okay so after my car charger "drains" my battery... I put the regular charger in and charge it from 74% to 85% in about 20 minutes... then I took the battery out and put it back in.. upon reboot my battery is at 97%... does this mean the car charger is somehow ACTUALLY charging the battery but for some reason making the phone think it's discharging it... this is tricky.
ericmcintire said:
okay so after my car charger "drains" my battery... I put the regular charger in and charge it from 74% to 85% in about 20 minutes... then I took the battery out and put it back in.. upon reboot my battery is at 97%... does this mean the car charger is somehow ACTUALLY charging the battery but for some reason making the phone think it's discharging it... this is tricky.
Click to expand...
Click to collapse
is the battery heating up while it is charging in the car?
I don't think so... I'm not 100% but I'd probabally remember something liek that
I just remember it was dropping like crazy after I plugged it in.. once it jumped from 39% to 34% when I was using it while it was plugged in for 4 minutes
ericmcintire said:
I don't think so... I'm not 100% but I'd probabally remember something liek that
I just remember it was dropping like crazy after I plugged it in.. once it jumped from 39% to 34% when I was using it while it was plugged in for 4 minutes
Click to expand...
Click to collapse
sorry, should have asked in my first post but are you running TomTom or similar?
no, no abnormal software... even turned off the 3g and wifi... I'm starting to think it's not actual battery drainage because of how fast it's dying.... it dropped to 2% and shut itself off last night when I plugged it in.. took 5 minutes to go from 28% to "dead" then when I was charging it in my house that night it slowly went from 0% to 45% then it jumped to 98% and was full.. I'm so confused
Maybe let the battery drain out all the way so the phone won't even turn on, and then charge it back up. I've never heard of this happening before, but I know the phone has to "calibrate" the battery, for lack of a better word. Draining the battery all the way lets the phone set a "zero point". I dunno if it will help, but it would be worth a try.
haha it kinda did that on it's own last night... recharged it, it's got the same problem as of 20 minutes ago.. maybe it'll work itself out.... but I really need to be able to plug it into my car.
This is my second Tilt I'm playing with as the first one after I messed around with started to act funny.
1) Battery would be 100% - I wake up 6 hours later and it's dead.
2) Network consistently was being dropped even though it stated I was connected.
I've spend 5 hours on this site reading now and still don't know if I've learned much lol
Good luck to you...
Check the USB port. Is it slightly bent on the right side? I had this same problem & had to RMA. I confirmed that there was higher discharge using SK Tools & Anton Tomov Batery Meter. However, home charger still worked fine.
GSLEON3 said:
Check the USB port. Is it slightly bent on the right side? I had this same problem & had to RMA. I confirmed that there was higher discharge using SK Tools & Anton Tomov Batery Meter. However, home charger still worked fine.
Click to expand...
Click to collapse
YES! the usb port looks a little messed up on the very last pin.. WTF? it looks squished or something... RMA? that doesn't sound good.. I hope I dont have to RMA... what's RMA? but yes there is definately something messed up about the right side of the USB port
ericmcintire said:
haha it kinda did that on it's own last night... recharged it, it's got the same problem as of 20 minutes ago.. maybe it'll work itself out.... but I really need to be able to plug it into my car.
Click to expand...
Click to collapse
Hmm... I would charge to 100% (or near enough) unplug it and then put the media player on and play it solid on repeat until the battery dies. Then charge it up to full again and see if there is any difference. These batteries don't have a memory as such, but as the previous poster said it may have got itself slightly 'confused'
Same problem here with a carcomm cradle for the TyTN II,. When I plug my phone in, the orange light comes on, the phone says it is charging but the battery just seems to drain faster and after a couple of minutes the light goes out. I have BatteryStatus installed, when I connect the phone to my pc with the standard usb/synch cable BatteryStatus shows +0mW for a short while and after a few seconds it'll say it's at +1300mW or something like that.
In the car when I put the phone in the cradle it'll show +0mW for a few seconds, then around -250mW (Idle) and the orange light turns off...
But I actually caught it charging once with +22mW when turning it on (from standby). I tried all obvious things, softresetting the phone while charging etc. But nothing helps, the cradle is connected straight to the carbattery.
botmans said:
Same problem here with a carcomm cradle for the TyTN II,. When I plug my phone in, the orange light comes on, the phone says it is charging but the battery just seems to drain faster and after a couple of minutes the light goes out. I have BatteryStatus installed, when I connect the phone to my pc with the standard usb/synch cable BatteryStatus shows +0mW for a short while and after a few seconds it'll say it's at +1300mW or something like that.
In the car when I put the phone in the cradle it'll show +0mW for a few seconds, then around -250mW (Idle) and the orange light turns off...
But I actually caught it charging once with +22mW when turning it on (from standby). I tried all obvious things, softresetting the phone while charging etc. But nothing helps, the cradle is connected straight to the carbattery.
Click to expand...
Click to collapse
check your USB port... is your's messed up too?? you know what? I probabally accidently poked the stylus in mine while trying to reset a couple days ago... since I tried to do 20 resets when I was rom upgrading and adding software...
ericmcintire said:
check your USB port... is your's messed up too?? you know what? I probabally accidently poked the stylus in mine while trying to reset a couple days ago... since I tried to do 20 resets when I was rom upgrading and adding software...
Click to expand...
Click to collapse
Just checked and yes it is, stylus thing happened to me also once....
It's a little bend downwards (when having the screen on top) @ the last 2 pins...
well looks like we've narrowed down the problem.. and it looks like the fix is gonna cost $80!!
http://www.pocketpctechs.com/main~u...T+Tilt+Sync+Connector+Replacement+Service.htm
anyone know of a solution we could try out? my other phone (s710) had a USB cover so this never happened
ericmcintire said:
well looks like we've narrowed down the problem.. and it looks like the fix is gonna cost $80!!
http://www.pocketpctechs.com/main~u...T+Tilt+Sync+Connector+Replacement+Service.htm
anyone know of a solution we could try out? my other phone (s710) had a USB cover so this never happened
Click to expand...
Click to collapse
What kind of carcharger do you have? Been reading about this problem and alot of ppl say the charger needs to be able to put out at least 1A for the phone to charge, I used some cheap cigarettelighter charger that was rated @ 650mA. It worked but charged so slowly that it would've taken days to fully charge. And besides that it didn't last long, 3 days before it blew the fuse and some more parts (worked for 2 secs after replacing the fuse)
I've tried several different ones... I think that since 3 people on this site all seem to have a "crushed" pin in our USB ports that's probabally the issue... now.. about a fix...
The amperage on your charger doesn't really matter. 1 amp is recommended so that you can use the device while charging, and the rate at which the battery charges does not diminish. If you used a 500mA charger, and had wi-fi & gps on, and media player blasting, for example, the battery may not charge at all because all the power coming from the charger is being used immediately. 1 amp chargers remedy this problem. Hope this makes sense, I've been having problems finding the correct words to express my ideas lately. Probably just stressed out! It sounds like the bent pin on the usb port may be resulting in a V+ pin shorting to ground (or V-). Which would drain the battery quickly. When you use battery power or charge the battery, it is normal for the battery to get warm. When you plug yours into the car charger (the one that drains it) does the battery get abnormally hot? This would indicate a short. Maybe try to put a real thin piece of film or something under the bent part of the port to insulate it while charging and see if that fixes it. This might offer a temporary fix until you get a new port. Maybe you could spend some time learning how to solder! I had to fix a broken port on a wizard a those solder points are friggin' tiny. Hope I could help. Good luck.
sWuRv said:
The amperage on your charger doesn't really matter. 1 amp is recommended so that you can use the device while charging, and the rate at which the battery charges does not diminish. If you used a 500mA charger, and had wi-fi & gps on, and media player blasting, for example, the battery may not charge at all because all the power coming from the charger is being used immediately. 1 amp chargers remedy this problem. Hope this makes sense, I've been having problems finding the correct words to express my ideas lately. Probably just stressed out! It sounds like the bent pin on the usb port may be resulting in a V+ pin shorting to ground (or V-). Which would drain the battery quickly. When you use battery power or charge the battery, it is normal for the battery to get warm. When you plug yours into the car charger (the one that drains it) does the battery get abnormally hot? This would indicate a short. Maybe try to put a real thin piece of film or something under the bent part of the port to insulate it while charging and see if that fixes it. This might offer a temporary fix until you get a new port. Maybe you could spend some time learning how to solder! I had to fix a broken port on a wizard a those solder points are friggin' tiny. Hope I could help. Good luck.
Click to expand...
Click to collapse
this sounds like it makes a lot of sense... I've got big clumsy hands, man I wish I had been more careful... well looks like I'm gonna be out $80! but quick question.. why would the wall charger operate normally while the car charger reverses charge?
Is anyone else having this problem?
Any work around to having it actually charge the battery up?
it uses electricity faster than its recharging its crap! ive never known any device do this. When im low on battery and have it connected to my computer i have to switch it to the mains for 30 mins. Its terrible, bad design fault
I have the same problem with my Toshiba G900 (WVGA too). Very slow on USB, but normal fast at standard charging or car charging. USB is very bad for this at all.
it really depends on what you're doing with the phone, its unlikely to charge when busy, its a lot faster at charging than my old advantage, im actually impressed!
have you made sure that you've not ticked turn off charging whilst connected to a computer?
charged in under 3hours whilst on connected to ubuntu yesterday.
don't u guys realized how many amperes that a USB socket and your PC (as well as the power supply) allowed compared to a wall socket?
usb chargin usually is never worth it.
I don't understand your disappointment, usb voltage/ampere are the same for all devices, even for my touch when used as modem doesn't supply enough power for charging seriously
Does it even charge at all via USB when the X1 is on idle? If it does, how long does it take from low to full?
I left my X1 idle on USB for 6 hours, it was nearly flat when I put it on and after 6 hours it was still 1 bar below full. Whereas my LG Viewty fully charged in about 2 hours. My Universal only takes about 3 hours
So in my case, comparing the three phones, you can see where my dissapointment originates from.
vinokirk said:
I left my X1 idle on USB for 6 hours, it was nearly flat when I put it on and after 6 hours it was still 1 bar below full. Whereas my LG Viewty fully charged in about 2 hours. My Universal only takes about 3 hours
So in my case, comparing the three phones, you can see where my dissapointment originates from.
Click to expand...
Click to collapse
But remember the size of battery the x1 has maybe the 1500 comes into play.
BuddyLee said:
But remember the size of battery the x1 has maybe the 1500 comes into play.
Click to expand...
Click to collapse
Well, of course. Xperia's battery is bigger. That's like complaining that your glass fills up faster than your pool. (may be exaggerating a bit )
BuddyLee said:
But remember the size of battery the x1 has maybe the 1500 comes into play.
Click to expand...
Click to collapse
True tho, point taken.....dissapointment level aleviating.....slightly....
After my phone beeped saying the battery was low, I plugged it into my USB hub (which has a mains supply). An hour later I removed the cable and the phone beeped again.
At least with my P990 I was able to gain some charge, it seems like with the X1 it just stops the battery running down.
Try it after Softreset again. I had this problems with an old ROM on my G900 too. After some time it did not charge. Softreset fixed it.
also yall are forgettin that it's a different kinda battery in the x1 compared to other phones it's ising a li-po compared to a li-ion (which is in most other ppc phones) it charges slower via usb because it's tryin to keep from exploding any extra surge that the usb gets could cause your phone to explain
the li-po is more likely to explain given the way it's built
when you use the wall chargers and car chargers the connection are ment fron rapid rechargin of the device unlike the usb which is for data transfer mainly
when you think about the charge time just think about how long it actually takes for your phone to run out of battery life from what i heard it's close to like 1.5 to 2.5 days compared to normal ppc phones that last probably a day at the most with out recharge
hope this help
Keland44 said:
also yall are forgettin that it's a different kinda battery in the x1 compared to other phones it's ising a li-po compared to a li-ion (which is in most other ppc phones) it charges slower via usb because it's tryin to keep from exploding any extra surge that the usb gets could cause your phone to explain
the li-po is more likely to explain given the way it's built
when you use the wall chargers and car chargers the connection are ment fron rapid rechargin of the device unlike the usb which is for data transfer mainly
when you think about the charge time just think about how long it actually takes for your phone to run out of battery life from what i heard it's close to like 1.5 to 2.5 days compared to normal ppc phones that last probably a day at the most with out recharge
hope this help
Click to expand...
Click to collapse
Err... this is not true for TP. TP lasts about 2 days on average from normal daily usage and it doesn't have problem charging via USB. Given that the port used is USB 2.0 not 1.1 or below. Took about 2~3 hours from nearly flat to full charge if I remember correctly. I have to try again just to make sure. But definitely not taking 6 hours.
I would've thought that X1 shouldn't have any problem with charging since the battery is only like 150mA more than TP. Also, if it's charging faster from the AC adapter, the same result should be expected when charging from USB port. Doesn't matter the type of battery used. Unless if X1 somehow limits the charging current on purpose when PC USB port is detected. Even though USB 2.0 is actually capable of giving out 1.5A maximum. Try to soft reset it after charging for about 2~3 hours. See if the battery gets fully charged. Some TP users are experiencing this issue as well when the battery meter only updates to fully charged after doing soft reset. Experienced users might want to try and measure the current drawn when charging via USB 2.0 port.
Hope this helps.
On my xperia if i put it in sleep mode, it charges no problem using USB.
the advantage used to charge slower from a usb port, that is until someone found out that the standard ac charger had a short across two of the usb pins, and with a quick mod of a usb cable charged quickly from the usb on a computer
however my x1 charges the same from usb or mains, I use the same cable, but can't see what difference that makes.
there are three conditions that affect charging speeds, whether device is on or not, off charges much faster, whether screen is on or not, screen off charges faster, whether theres good radio signal, if like at home, reception is dodgy it can really draw a lot of juice.
Just for comparison sake, I did a test on my TP just to confirm. Charging via USB 2.0 while it was on idle with screen turned on, from 4% to 100% it took about 2.5 hours and its battery feels warm.
Ok lets clear out some things.
A standard PC USB socket can provide maximum 500mA (milli-Amperes) Current at 5 Volt. Ideally that means that a battery rated at 1500mAh (milli-Amperes-hour) can be charged around 3 hours (minimum). Now, subtract the current that the xperia needs while operating and you will get how many milli-Amperes are left for charging.
Of course in order to know how many current the xperia needs to operate you need to connect an ammeter in series, also keep in mind that current needs change depending on usage (wifi, 3g, bluetooth etc).
So in essence if you USB port is not very good and can't give fully 500mA and the xperia needs a great amount of current to be on, then the charging time can be quite long. A simple formula could be:
xperia_Battery_mAh / (USB_Current - xperia_Current)
Now the mains charger is rated at a greater value than the USBs 500mA. Actually I don't own yet an xperia (waiting patiently to arrive), so I don't know how much current the charger can give. Can someone see what is the rating of the charger?
From other devices I own (that can charge through USB) I've seen that their chargers are rated as high as 2 Amperes. Obviously these devices never draw so much current, it is just a failsafe or it was more cheap for them to bundle a charger like that. But they could draw 800mA of current which the USB port is unable to do so.
Keep in mind that while charging with USB might be longer, generally it can be safer for the battery (longer battery life and more charge/discharge cycles), although I am not so sure about this with excessive charging times in a USB port.
Within the last few days I've notice that my phone is charging at unbelievable slow rate via the wall charge that was supplied. I usually get a full charge in maybe 1-2 hr depending on what percentage the battery is at. Once it is fully charge it hold the charge, but when it drains then it would take like 6 hrs to do a full charge. I've tried to soft reset it to see if the percentage goes up, but it stay the same. I turn off the phone to let it charge, but it still charge at a slow rate. I'm wondering is it time to purchase a new battery.
What do you think? And is there any other test I can do?
The slow charge could be one of a few things... One could be the battery as you suspect (and probally most likely).. Also, are you chargign the phone in a diffrent place? If the battery gets too warm from lack of circulation, it will not charge (or just charge much mroe slowly).. It also could be that your USB port is starting to go... IF you have a stand alogn abattery charger available for it (like one on a docking station) try to charge it on there and see if it still charges as slowly.. Another though could be if you are charging it in your car while using GPS or Wifi.. IF those are left on, they suck down the battery a lot faster and thus it uses the electricity as fast as it can pull it in.. I woudl suggest powering the phone down while charging.. that could also help...
i always charge it in the same spot since i got the phone. i dont have a dock charger. its weird last night i was at 49 and i turn off the phone completely and plug it in. woke up today the orange light indicating that it was charging still was on. turn on the phone and it was at 55 percent. WTF!!!!!!!!!!
I guess that touch pro 2 better come out soon.
itzstevo said:
i always charge it in the same spot since i got the phone. i dont have a dock charger. its weird last night i was at 49 and i turn off the phone completely and plug it in. woke up today the orange light indicating that it was charging still was on. turn on the phone and it was at 55 percent. WTF!!!!!!!!!!
I guess that touch pro 2 better come out soon.
Click to expand...
Click to collapse
i have the same problem. Its either your USB port or the charger, so simply go buy a new charger and if it still does it the port is bad....if not, problem solved
or put it in your computer to charge, that avoids buying a new charger.
usb charging is always slower then wallplug charging as usb can only provide
5v * 0.5Amps == 2.5Watt
where
wall charger can provide as much watt
as the charger is made to
but of cause the pda will only draw as much
amps as it was made to support
Recently my X1 cannot be charged with USB cable through wall outlet & even car charger , but able to charge with USB cable through PC.
Anyone do encounter the same problem?
Well that's a strange one - how long was it connected to the wall?
Without getting into the discussion about volts and amps provided, and amps drawn by the phone, any method should charge.
In terms of speed, I would think the wall would charge fastest (see above), and the USB slowest.
Did the phone show on the top bar, the charging icon when attached to the wall? Or after a period of time there was no increment in the % charge showing??
If the battery was down to 0%, you probably wouldn't see an immediate increase in the % charge. The % charge is orientative, especially at both ends of the scale.
paul c said:
Well that's a strange one - how long was it connected to the wall?
Without getting into the discussion about volts and amps provided, and amps drawn by the phone, any method should charge.
In terms of speed, I would think the wall would charge fastest (see above), and the USB slowest.
Did the phone show on the top bar, the charging icon when attached to the wall? Or after a period of time there was no increment in the % charge showing??
If the battery was down to 0%, you probably wouldn't see an immediate increase in the % charge. The % charge is orientative, especially at both ends of the scale.
Click to expand...
Click to collapse
I do agree with you. Charging with wall outlet is faster. Therefore, normally I'm charging my X1 with wall outlet, unless in office, will use PC USB.
Top bar never show charging icon, but once I charge it with PC USB, the charging icon show up immediately.
It seems like no power for the USB when connected to the wall outlet. I've tested with battery removed, plugged in USB cable connected to wall outlet, there is no charging illumination light. I cannot power on it.
I tried to recall, it happened after I used a USB charger for my MP3 player. The next day, when I tried to charge with car charger. To my surprise, the USB connection notification showed up (I do remember, while charging with wall outlet or car charger, it will never prompt me for USB connection).
I don't think, it is the ROM issue. Try a few ROM still having the same problem.
From now, I got to live with PC USB :|
X1 Charging problem
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
torquefever said:
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
Click to expand...
Click to collapse
let's me try with power off charging with wall outlet
well thats why se said USE only original accessories...you need to change the power ic on the board.
donottouch said:
well thats why se said USE only original accessories...you need to change the power ic on the board.
Click to expand...
Click to collapse
will the SE service centre entertain changing 'power ic'?
make sure your charger have an out put minimum is 1.Ah ,if lest than that it will not work , that is the troublem
nguyennghiep said:
make sure your charger have an out put minimum is 1.Ah ,if lest than that it will not work , that is the troublem
Click to expand...
Click to collapse
I'm using the original SE charger!? I would not think the problem with the charger, but my X1 was screwed by the incompatible MP3 USB charger
Yep same with me, not sure why mine started doing that though, I never got used a cheap charger. Maybe its the rom... I am trying a new one now.
torquefever said:
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
Click to expand...
Click to collapse
digitalspree said:
Yep same with me, not sure why mine started doing that though, I never got used a cheap charger. Maybe its the rom... I am trying a new one now.
Click to expand...
Click to collapse
it's not caused by the ROM, I'm very sure. I've installed different ROM. The problem still exist.
I am having a similar problem. When the phone completely discharges , i am unable to charge it with any power adapter or even car charger. I have to initially charge the phone using a PC , then after the power is around 15% , then the phone gets charged with a normal adapter.. any suggestions??
same problem. It happends when the battery is completely discharged.
what I do is use a charger w/ low amp rating (.1) and plug it in for at least 10-20min. Give it some time, it will start charging after a while (indicated by the blinking lights). After that, you can turn it on and charge it normally
I had a similar problem twice.Both times I solved it by replacing the charger.
the same happen to me and i have another issue
my xperia doesnt work as usb mass storage!!!
the solution was buying another charger but..the usb mass storage issue still not working as a flash drive!!
luirhy said:
same problem. It happends when the battery is completely discharged.
what I do is use a charger w/ low amp rating (.1) and plug it in for at least 10-20min. Give it some time, it will start charging after a while (indicated by the blinking lights). After that, you can turn it on and charge it normally
Click to expand...
Click to collapse
It works with Z1 too. Thanks a lot!
I guess something goes wrong with battery controller