Hi all, I want to use my Diamond as a USB stick to connect to my car radio, wich has an USB port. When I connect as diskdrive it seems to work fine, I can play songs from the 4GB internal mem. But when I leave a song on for a few minutes, it seems to lose connection, and then I need to unplug the USB to get it to work again. Ofcourse it doesn't continue where it left off, so it's pretty annoying. A friend of mine who has a Diamond and a USB car radio has the same problem. Does this sound familiar to anyone, and is there a fix for this? Many thanks.
did anyone find a solution for this?
Hi guys,
i have one very strange problem regarding TYTN II. It is almost new device, barely used but following things are happening:
1. Can not be charged while it is switched ON. In order to charge the battery i have to turn device OFF and than to connect it to the charger. Red light is instantly on and charging.
2. While it is ON and i connect it to the PC using USB cable, it is not recognized from operating system (it is not charging as well, it will charge though if i switch it OFF, same as with charger)
I can connect to my Tytn II using bluetooth and i have some questions.
Can i do HARDSPL 7 while conected to Tytn II via Bluetooth?
I want to upgrade my ROM using upgrade from SD card because obviously upgrade can not be performed using USB cable.
I did hard reset before i put this issue on the forum, can this be caused by the software or only hardware?
Thanks for input.
Jeremija
Check the settings->System->power. check whether the option "When device is turned on,do not charge the battery when connected to the pc" is selected. if so unselect it.
Already did that before first post, that option is not selected.
It is not only charging but TYTN II is not recognized while connected to the computer via usb cable.
this tytn ii is getting charged only and only if it is switched OFF, source can be computer or original charger.
I can get connected via bluetooth for data and my other question is if i can do HARDSPL 7 through bluetooth conection?
thanks.
jeremija_de_niro said:
Already did that before first post, that option is not selected.
It is not only charging but TYTN II is not recognized while connected to the computer via usb cable.
this tytn ii is getting charged only and only if it is switched OFF, source can be computer or original charger.
I can get connected via bluetooth for data and my other question is if i can do HARDSPL 7 through bluetooth conection?
thanks.
Click to expand...
Click to collapse
If its vista system then you probably need to disable the advanced USb functionality and try again.
To your next question, i havent seen anything till now that talks about flashing through bluetooth.
it is happening on both, vista and xp.
that is interesting question actually. Did anyone tried to flash over bluetooth connection, without using cable?
I would certainly prefer to use cable but my tytn ii does not get recognized when connected with the cable.
thanks
What have you done on the PCs to prepare them first?
Have you installed the software in the box on your PC before connecting the USB cable (Activesync 4.5) for Win XP desktops or the latest Windows Mobile Device Centre for Windows Vista? You need these before it'll connect/sync even though it's possible to use bluetooth without it.
Yes, on XP is installed Active Sync 4.5 and on vista i am using is latest Windows mobile device center.
Did you try disabling Advanced Network Functionality on the phone?
So other than trying what was already suggested and disabling Advanced Network functionality on the phone, I think it's time to call your countries HTC Support people.
FWIW whether or not you can use Advanced Networking Functionality is determined by the capability of the USB ports on your desktop PC. When I first got my TyTN II I couldn't get it to connect/sync at all and through trial and experimentation I came across the disable advanced networking workaround. Even with it disabled though I still found my Activesync connections to be unreliable and subject to frequent disconnections. I was using the native (and old as the hills) Via Appolo Pro USB 1.1 ports on my motherboard. I decided to upgrade to USB 2.0 so installed a quality NEC chipped PCI USB 2.0 adapter card. That means I now can use Enhanced Networking Functionality and I have not had an Activesync connection fail since. It was well woth the £9 it cost me for the card.
Everything is clear, thank you very much for your replies and advices. I`ll try to find HTC authorized service and let them judge
Thanks once again.
Jeremija
Is WiFi on?
My Vodafone v1615 (Kaiser) will not connect over USB if WiFi is enabled. No connection problem when WiFi is disabled via Comm Manager. Suggest you try this.
I tried everything i could think of, with or without sim card, with flight mode on, with GSM on but wireless off, name combination i tried it. Gave the phone to the friend who has exactly same model to try with his battery and if that does not work than i`m out of ideas except to send it for service.
I also noticed that if i leave phone on charger and OFF, red light lit for charging.
It can sit on charger for 24 hours but light does not change color to green (Full battery) but remains red.
I believe there is a problem either with battery or some component which is tightly connected to the usb socket/battery.
Will post results on monday/tuesday when i get my phone back.
Thanks everyone for input.
Jeremija
Same Problem
Just so you know i have EXACTLEY the same problem as you Jeremija... i have NO idea what is Causing it have you had any glory yet??
Kindest
Ben
Same problem as well
I just got my phone yesterday, and it had the same problem out of the box
it will not charge unless it's completely off, and it will not sync through a usb cable, when i connect it through USB it just keeps restarting, If anyone can come up with a solution short of returning my brand new phone back to the factory I would greatly appreciate it
USB charge & sync problem
What you have with your phones must be a hardware defect. I have the exact same problem with my Tytn II, but I know how it happened -- out of full stupidity. While at work, I connected it to a mini USB plug to charge, however to my surprise I found out that it was not 5v but 12v. I bought two external chargers and two extra batteries and I've been carrying around a pair of charged batteries since then. To be honest, because the phone notoriously drains the batteries very quickly having spare batteries is more practical than pluging it in and waiting for it to charge.
Hi All,
I've been running hyperdragon III for past six months or so with no problems, however, of late i'm having issues when connecting my tytn ii to the PC. It's stating the usb device is not recognised and therefore cannot perform syncs etc.
I've tried on two different machines one with vista/Mobile Device Center and another with XP/ActiveSync 4.5 and two different usb cables, I've performed a hard reset but with the same results.
It seems i'm unable to update/rollback my ROM due to the fact i don't have a succesfull usb connection!
Please help!!
Thanks
maybe your usb port is borked like the ones of some other kaiser users.
does it charge when connected to the wall charger?
for the rom flashing: you can also flash a rom from your sd card. have a look at the wiki as i don't know the excact process and dont want to bring you in more trouble you already are
Hi
Thanks for the prompt reply.
The phone does charge from both the charger and the usb cable.
I'll take a look at ROM via sd
Just updated the rom from hyperdragon iii to iv via sd card, still no joy. windows states device unrecognised!
Any ideas anyone? Really need this device to sync, especially now i've done a hard reset and lost all my contacts!
Try syncing via bluetooth?
Indeed most likely your USB port is broken. Search this forum a bit, it's full of such occurrences so it isn't a rare thing at all.
for the time, your usb port is broken and if you dont have bluetooth.
mail2web.com offers a service called mail2web live. its a free exchange 2003 account. You can sync contacts, calender and mail with that server using wifi or 2g/3g. and for the files, try livemesh ( mesh.live.com )
i've active sync configured at home but i havent used it for a few weeks now thanks to live mesh and mail2web.
btw. have you tried if it's charging when connected to the wallcharger / usb port?
OK thanks for all the info, i've rolled back to the original orange ROM in prep for sending it back to orange for a replacement (still under warrenty) but i'm unable to find the original orange splash screens, any ideas where i can find them?
Thanks
Hi,
I'm new to Windows Mobile, so I'm not entirely sure what I'm doing. I've just bought a TyTN II (Kaiser) from eBay second hand, and I'm having a little trouble getting the PC to recognise it.
The phone is locked to the Orange network. However, it would appear that it has some custom firmware on, as the orange homescreen that I was expecting isn't there (which I'm very pleased about). In About it says "Windows Mobile 6.1 Professional (Build 19209.dutty's WM6.1)"
When I connect the phone via USB cable to a PC, it's recognised as being there, and the PC tries to install software but fails, saying it can't find drivers. On the disk which was supplied is some BlackBerry Connect software, which doesn't seem to help when I install it. I've tried to install the phone on XP SP3 and Windows 7 build 7000, both saying that the phone can't be installed, and ActiveSync / Sync Centre say the phone isn't there.
The phone charges up fine when plugged in either via USB or Mains, which would suggest to me that the socket on the phone isn't faulty, but instead it's a software fault with the phone.
Thanks in advance.
Thomas
Solved it now.
For future reference for anyone having the same problem, try this thread: http://forum.xda-developers.com/showthread.php?t=309102
I tried to upgrade my qtek2020i to this ROm "Alpine_ROM-1.11.00WWE_Radio-1.04.00_ExtROM-1.11.180" now my screen is stuck on serial v 1.01.
i searched the forum fixing it by using cradle and a SD cradle, but the problem is i dont have cradle neither SD card, and cradle is kindda not available in my city
i'm trying to do it by using bluetooth i start the update again now installation is on "checking the information on your device" since 15min and my bluetooth port is in use does it mean its still upgrading or not?should i wait for it?