I got the tilt 2, had a few before did hard spl with little problems, just got a new replacment in the mail, and the hard spl dosent seem to be working, i tried diffrent usb cables, diffrent ports, diffrent computers. i turned off fast tranfser for active sync, everything nothing works please help):
Related
Ok, here is the deal. I have 3 tilts that have all been edwith different roms using the same computers (3 to be exact) in the past. Now none of the phone can get a usb connection no matter which of the three computers I used. I have tried alternating each phone with each computer but still no results. I did the soft to hard resets. Installed new drivers on PC's and no change. Toggle the usb-PC connection check box...I mean everything. Can someone help thru this?
Ok, I posted a thread on the main wizard forum and I'm trying again here since this is a little more on topic in this forum.
Here goes with all the technical specifics I can add in.
I recently got an HTC 8125 (I've had one before and never had this problem)
I immediately CID and SIM unlocked the phone using lokiwiz's unlocking program.
I inserted my tmobile sim into the cingular 8125 and all was great.
I upgraded the ROM to the TNT 19199 batch of WM6.1 Everything is still great.
The phone worked awesome, the next day I downloaded the T-Mobile UK radio version 2.19.11.
I flashed it to the phone and everything seemed fine, the program finished and the phone restarted.
Upon restart I was greeted with a no service message and the phone behaves as though it is shutoff. No big deal, right? WRONG...
I went to the tmobile and cingular site and got the default roms from each just in case.
I then connected the phone to the usb and activesync would not recognize the phone, or do anything for that matter.
I used an external USB bluetooth dongle to try and connect the phone to the PC to flash the default rom and fix the radio problem, this wouldn't work either.
I then put the phone into bootloader mode, this works ok, I see the USB in the corner and figure I'm saved. Nope.
I ALWAYS get an Error Connecting from the rom software. Even though my PC recognizes the phone, active sync does not. I re-installed Activesync and rebooted my computer numerous times. To no avail.
The ONLY rom software I which has worked is the TNT 19199 but it doesn't fix the lack of radio.
Here are some other points of interest. On phone bootup I get this:
IPL 1.08
SPL 1.08
<----Notice, NOTHING in the GSM spot.
OS 1.11.1.0.1 (or whatever the numbers are for that particular rom)
The USB will recognize the phone ONLY in bootloader mode, otherwise when the phone is on the Today screen I get no recognition.
The TNT rom has worked twice when I tried it, (by worked I mean it allowed me to re-flash the same rom) Of course the TNT rom doesn't work all the time, it has given me several connection errors.
No other rom has worked as of yet, all others give me a connection error.
The battery meter will not display, nor will it tell me what type of battery or how much charge is left.
The phone will sometimes go to amber light when plugged into the wall charger but NEVER with the usb to PC cable.
I can still navigate around the windows mobile 6.1 interface though it moves incredibly SLOW. i.e. I pushed the comm manager button to make sure the phone didn't simply get shutoff and I waited about a minute and a half or longer for it to bring up the comm manager.
I need some severely good advice and some new tricks to try, I'm running out of ideas, I saw several threads under the HTC TyTn threads about similar problems and something about the IPL/SPL being important but I'm not sure what they're talking about. I have searched this forum and I have found people talking about similar problems, all the responses point to, "If you can get to the bootloader you're fine." This is incorrect.
So seriously, help me out here.
HOW DO I FIX MY STINKIN' PHONE.
I would suggest rolling back to your working configuraton by reflashing using a memory card instead of the USB.
fixed.
Actually I finally figured it out.
It seemed the reason that those roms worked sometimes but not others was this: To get the phone to recognize you had to do things in a VERY specific sequence.
You had to let the phone boot all the way into WM6 and then plug in the usb cable. Then put it into bootloader with the camera / soft reset button method. Then you waited for the nice USB connect sound, and began the ROM flash RUU program. (In this case it was the T-Mobile default rom).
Once that was done the phone acts as normal and everything is good.
Doing anything out of order or putting the phone into bootloader without it having first booted all the way to the OS would give you the connect error.
Please clarify if you're running WM6 with IPL/SPL 1.xx? I believe that's not possible to get good results that way.
IPL 1.08
SPL 1.08
<----Notice, NOTHING in the GSM spot.
OS 1.11.1.0.1 (or whatever the numbers are for that particular rom)
TNT 19199 batch of WM6.1
Wm6.1 on ipl/spl 1.xx,strange ,how do you explain this,how did you manage to get wm6 installed with ipl/spl 1.xx,cuz it only works on ipl/spl 2.xx and higher. Are you sure its TNT 19199 series wm6.1 Rom ?
Thanks for taking the time to view my issue.
Lets start from the beginning
My 8925 has been Hard SPL'ed and SIM/CID Unlocked and the first rom i loaded on to it is Phoenix Development Team's PX 2.3.2109.2g
All was well and i was the happiest little boy who ratted on iphone owners.
Then i damaged the USB/Sync port by jamming my stylus in it looking for the reset button. I had the port replaced yesterday and it's charging fine the issue is every time i connect it to my XP based PC i keep getting USB unrecognized errors.
I've been spending the past two three hours messing around with settings and over a few dozen forums looking for a solution. Here's what i have done so far:
Hardware
- Attempted to sync my device on 3 different computers, 2 use XP, the other Vista. One system gives me the 'USB deviced unrecognized' error the others dont but do nothing to indicate they recognize the device
- Used over 4 different USB to miniUSB cables with no success
- Tried all the different USB ports on all 3 machines
Software
- Messed around with the connection settings in an attempt to get it to sync with no success across all available computers
- Done several hard resets to restore the OS to factory settings
- Preformed a mini-sd rom flash to the shipped factory version of Win Mobile 6.1
- Shut down firewall/antivirus programs that might be blocking the connection
After all the stock rom flashes and hard resets i've done the Phoenix OS's loading screen (shows Rom, radio, and protocol version) always appears then regular factory windows pops up. Not sure if this is an issue or not.
Is there anything else i'm missing or other steps to help me determine if i need to change a few more settings or call the guy that did the repairs and ask him to reinspect his work?
Thanks
Hi All,I bought an 8125 Cingular Device (I am att),it had shells,and programs installed and unistalled so many time along with must have been 25 different trick little "Mod" programs,this thing didn't know which way was up, So I cleared the Storage and let it download all of the default stuff, THE IPL/SPL are both at 2.25. The Computer won't recognize the USB Connection though I can recharge through the port just fine,when in "Com Manager" there is no way to enable Activesync,no matter what it has a "Check" through it,i think it is hardware screwed inside.It has Windows 5 on it ROM Version 2.25.11.1 WWE Dated 5/11/2006,Radio 2.25.11,Protocol 4.1.13.12,Ext Rom Version2.25.11.102,I have tried many different things to get it to recognize the USB to Activesync with no go. I don't think it is CID unlocked or SIM Unlocked. Is there a way to Upgrade my ROM (from what I gather it is a G4)using the Storage Card? There was a shell from SPB on it that was all screwed up with Pocket Plus 3.2 ,My son put a SHell on it 3.01 Final in order to try to make it behave better,It was some better but it has had so many Mods in and out of it with I am sure shared files being deleted that I decided to clear storage.SO,Now I am back to stock with the SPL/IPL at 2.25 and A Non Functioning USB COnnection,I know the Cable and PC are good as we have several other smartphones in the House all working fine. I would like to put the Wizard 6.5 or a Cooked 6.1 on it.I have downloaded the 6.5 ruu and was hoping to install it with the storage card method.can the phone be unlocked by placing the lokiwizprog on the storage card with the PC?Thank You in Advance for any Info you can provide in Advance. I have read probably too many threads and confused and probably over complicated the process.I have seen the "bricked" posts and don't want to go there.It is not a matter of laziness that has me inquiring,I have upgraded several different types of phones and have been in the Satellite Hobby Many years ,so I am fluent in Flashing Chips,loading software ect. So Far I have Downloaded "the Buttom Rom","Lokiwizb", and the "6.5 Wizard Rom"Thanks,Vegas
In short you won’t be able to do any of the things you want without a functioning USB port.
So let’s find out if the USB port really doesn’t work.
Turn the phone off, press and hold the camera key, now insert the USB data cable, you must continue to press and hold the camera key until you see the boot loader screen.
On the boot loader screen you will see IPL SPL and on the bottom of the screen USB, if you don’t see the USB on the bottom of the screen then something is wrong with the USB port.
You suggest your phone is a G4 yet you put IPL\SPL “2.25”
If your IPL\SPL 2.25 = G3
If your IPL\SPL 2.25.0001 = G4
Same Issue
I'm having same problem on my wizard, however I resoldered the mini USB port.
It did pop up in Win 7 x64 generic RNDIS driver not installed, no other indications of it being connected, charges fine, boot loader detects USB at bottom of screen, tested on XP also with no positive results.
Hi all! I've bought an HTC AT&T Tilt recently but it really turned out to be not so good of a deal. First of all if the phone is turned on the USB just doesn't work. I mean no charging, no connection to PC etc. If it's off it charges normally. At first i thought that it's a hardware issue and I just gave away money for nothing. After I started playing with it I noticed a few things. I ran Android through Haret and the USB works magnificently. Charging, connectivity and so on. When I switch to WinMo - bump. I tried 3 different comps and 4 different cables but still nothing. Read some threads here and there but as far as I could tell I still need USB connection to flash the device. So no HardSPL as far as I know. The USB port on the device is in perfect condition(at least to my knowledge). I cant's even use the phone because it's AT&T network locked and to unlock it I would still need USB connectivity! If anyone has an idea how I can flash completely via MicroSD or anything else I'd be really thankful. Thanks in advance!
I forgot to write current sw versions:
R 1.65.21.18
G 25.88.40.05h
D 3.57.00.00
And at bootloader:
KAIS1*0
SPL-3.56.0000
CPLD-8