Hello All,
Just put a new 120GB hard drive in the HTC shift and loaded Win7 on it. I went though all the steps on this site (which were very good btw). I got touch screen working, I got internet though the SIM card and the resolution looks good.
The only problem is that device manager shows there is no wifi or bluetooth hardware. The drivers for the wifi seem to install fine, but there are no wifi settings nor is there wifi hardware listed in device manager.
Any help here would be greatly appreciated
Hi!
Did you enable wifi and BT using the Shift Control Center? For wifi I know for sure that it's "disconnected" when disabled. Might be the case for BT, too.
Regards,
Sven
CaptainKirk said:
Hi!
Did you enable wifi and BT using the Shift Control Center? For wifi I know for sure that it's "disconnected" when disabled. Might be the case for BT, too.
Regards,
Sven
Click to expand...
Click to collapse
Omg, that's what it was... Unbelieveable. Sven, you have saved my week.
Thank you so much, I can't believe it doesn't even show up in the device manager after a fresh install, I was going crazy for a few days.
"Just put a new 120GB hard drive in the HTC shift"
Could you tell us what make and model you used, and was it a big deal to get it in there?
regards
Sudipta
Dog**** said:
Omg, that's what it was... Unbelieveable. Sven, you have saved my week.
Thank you so much, I can't believe it doesn't even show up in the device manager after a fresh install, I was going crazy for a few days.
Click to expand...
Click to collapse
I'm glad that I could help you. Now have fun with Windows 7. It's much more responsive than Vista even when Aero is enabled (and I love the fast stand by )
Regards,
Sven
Related
Hi guys and girls.
I finally plucked up courage to install WM5 and suprisingly, it worked like a charm! not one single problem
There is one cherry on the top that would be very nice if anyone can help.
On the today screen there is a nice little bluetooth icon in the bottom right hand corner; is there any way to get a wifi icon next to it instead if having to go into start > Settings > connections > WLAN to turn it on?
Appreciate any suggestions offered.
Cheers
J
can someone please send me the orginal wirelessmgr.exe file? i tried to load the wirelessmgr.exe from the universal and now i cant turn wireless on or off
Codiac, I have taken a hotkey (camera, I don't use that much anyway, but any key would do) and mapped that to WLAN_MAN. Works very nicely, but I hope there will be a fix for the dissappearing WLAN (and BT, even though that doesn't matter that much to me since I never turn off the unit when I'm using anything BT) in the near future.
I never thought of that works spot on now :lol:
Must remember in future to engage brain before fingers :?
Cheers Mastiff
J
I added the program into O2plus apps tab
Codiac said:
On the today screen there is a nice little bluetooth icon in the bottom right hand corner; is there any way to get a wifi icon next to it instead
J
Click to expand...
Click to collapse
Codiac... how did you get the bluetooth icon on the Today screen? I just upgraded to Mamaich's Patch 5 but I don't have a bluetooth icon
me too..i can't see the bt icon and sometimes i quicly need of it..how can i show it?
Read the Wiki about missing files, patches number 1: http://wiki.xda-developers.com/index.php?pagename=BA_WM5_Patches_ChangeLog
This is wierd?!?
After I did the upgrade the nice little BT icon was on the today screen, never bothered with it because BT is useless. Read these posts and had a look to see if I could work out how it got there and it has dissapeared?!?
The only thing I can think of is that I accidentally uninstalled one of the patches downloaded from wiki.
ill try and get it back on and let you know how I did it
Cheers
J
OOPs, sorry should have read Mastiffs post properly first
Mastiff is right, you need to install ba_wm5_fix_v1
Cheers
J
Well I've installed the BA_wm5 patch, but still have wifi problems. On 2003 my BA used to turn on wifi every time i turned on the unit, great as i have wifi at home and at work, now it always defaults to off and I have to switch it on every time I've turned off my BA. It's driving me nuts as I use email via wifi at work all day. Is there any way to get the wifi always on? Please....?
That's what I've been *****in' about for more than a week now...
Surely there's a way to default wifi to on, here's hoping somebody works it out before i downgrade to 2003.
i douwngraded to wm2003se..wifi on wm5 don't work at all..dosn't connect on my AP (on wm2003se is very fast)..so..because i need it i'll wait a more stable version..perhaps backlight regolation will be fixed
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Mastiff said:
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Click to expand...
Click to collapse
The default to off is the problem. I use my BA for work only. At home I use my wifi network to access work schedule appointments, and when in the office I use their wifi hotspot. At present i am having to tun on wifi realistically around a hundred times a day to update my joblist.
Is there a way to add any sort of utility to startup to turn it on at power on maybe?
I've tried everything to make my WiFi work but no luck.
However, I think I'll hold on because I really like WM5. I've ran through all the registry setting but nothing I've tried so far has made a difference. Enev tried downgrading the encryption settings on my MIMO. Furthermore, when I take off SSID broadcast, my BA seems to be able to see the AP but still fails to connect.
It's really annoying because I like to synchronize Avantgo over WiFi and most importantly use my BA when I'm in the bathroom doing you know what. Somebody please help!
Hey Mastiff, what security settings have you got enabled on your Access Point?
Mastiff said:
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Click to expand...
Click to collapse
Cytrax, did you install activesync 4 to upgrade your rom? You can't sync by wifi on activesync 4 at all, they've removed the option from the program!
cytrax, I have 64 kbit WEP and MAC access control since the 128 kbit WEP was slow to access with another CE unit I have.
Thanks for that info, mastiff.
OK, this is wierd! At this particular point, WiFi works on my BA. However, it only works when I'm at work. The settings configured on Work AP is very similar to what I've got at home. The only difference is I use Netgear MIMO at home while Buffulo Airstation is deployed at work. This is really freaking me out (well, not exactly, but it's annoying).
I also tried with an old Belkin AP last night but didn't get any luck. I think I'm going to try 64bit WEP once I reach home. Watch this space!
Mastiff said:
cytrax, I have 64 kbit WEP and MAC access control since the 128 kbit WEP was slow to access with another CE unit I have.
Click to expand...
Click to collapse
Hey everyone, i just was getting ready to update to the new core rom (from xplore 1.1) and i plugged in my Tmobile mda into my pc that is running xp, and it is not connecting. When i plug it in it like doesnt even try to find it. And when it does try to find it, it just says it can't establish connection with your item.
I was using xplore and this is the first time i had this problem ever. Ive flashed 4 or 5 times and this has never happened, and thats why im posting it in the wm6 forum.
Does anyone have any ideas? HAs this happened to anyone else?
Now i am back on the newest tmobile update, and it is still doing it. Also i installed the newest version of active sync. Still no go. Also i used shell tools to put xplore on my phone, could that have left out some active sync's files? (probably not, last time i put nottosmarts rom on here everything worked perfect.
ipl 2.26
spl 2.26
gsm 02.25.11
os 2.26.10.2
love you
umm....no one?
can't someone at least flame me or something? im still stuck
jawnsixteen said:
umm....no one?
can't someone at least flame me or something? im still stuck
Click to expand...
Click to collapse
I can flame you , lol
If you can't connect, how did you flashed the latest TMobile ? I am not making fun, I really want to help.
i threw it in bootloader mode. It said usb in the bottom right hand corner. It's just that activve sync is not connecting with it. i wouldnt even care, but i think you need an active connection to active sync when you flash with shell tools, which is what i do.
update: i just succesfully sync'd to my laptop running windows vista.
anichillus, do you know if shell tools will work with the new way to flash with vista?
thank you so much for reponding, i really appreciate it...a lot lol
the only reason im doing this is to get to your rom!
jawnsixteen said:
i threw it in bootloader mode. It said usb in the bottom right hand corner. It's just that activve sync is not connecting with it. i wouldnt even care, but i think you need an active connection to active sync when you flash with shell tools, which is what i do.
update: i just succesfully sync'd to my laptop running windows vista.
anichillus, do you know if shell tools will work with the new way to flash with vista?
thank you so much for reponding, i really appreciate it...a lot lol
the only reason im doing this is to get to your rom!
Click to expand...
Click to collapse
I really really don't know that sorry ... I am using WinXP and not shelltool.
Also, why are you using Shell Tool ? Dont't you have G3 ?
Unlock it and easy as pie. I remember papamopps saying that it is possible to flash in vista ...but i don't remember anything about shell tool ...
BTW, you have ZoneAlarm ..or similar installed to the PC where you say that it doesn't connect ? Try and disable firewall ... antivirus ..stuff like that.
well i just don't want to void my warranty, but ill definitly try turning off all the firewalls tommorow when i get a chance, i think im just going to give it a go with shell tools right now and hope for the best
Thank you so much and if you ever need anything i would love to help you in return.
you're the best!
i have the same problem..active sync doesn´t find my wizard..but it´s charging normally, but active sync doesn´t recognize it or i don´t know..what should i do?? i didn´t do any change on my pc..and before it works good..
If you're using Microsoft's OneCare then you may have to enable the Allow ActiveSync to get it to work.
Start OneCare then click the "Change OneCare settings" link on the left
Click the Firewall tab
Click the Firewall connection tool button
Place a check in the ActiveSync/Windows Mobile Device Center" checkbox
Click Okay back to the main page
Hope this helps, but like Anichillus said, it could be any other firewall application blocking it...
yes! all i had to do was turn of norton for a bit and it instantly recognized my device. I was just so confused because this has never happened before and thats why i haven't thought of such an easy explanation. Thank you both for giving me your clear thoughts! lol
Another resolution idea
I had the same issue - I would plug the device in through USB into Vista Ultimate with no results other than the bing bong noise it makes on connection. Checking the device list showed the network pieces being added, but not the actual Wizard itself in the Mobile Devices section. I could not sync, it would not pair, etc, etc.
Resolution (on the Wizard):
1) Settings->Connections->USB to PC
2) Turn off "Enable advanced network functionality"
This of course will not be the resolution for everyone, but in case someone else sees this behavior, here is a list of the symptoms I saw:
1) Plugging Wizard in via USB causes Bing Bong noise
2) wmdc shows no connection
3) device manager shows no Mobile Devices section when connected
4) device manager network adapters may show mobile device services when plugged in
5) If connected in bootloader mode the device manager will show the mobile device
6) You can set up a bluetooth connection (if available on the PC) and sync properly with it
Cheers,
Shoogi
Shoogi, what an awesome first post! Worked perfect for me! Keep it up, great post and lots of help!
i have a problem that when I plug my device active sync connect it and charging starts but after a minute or so active sync disconnected and charging also stoped.
I have installed everything official > rom,radio,ipl/spl etc.
One Care made activesync almost unusable for me. I also had to reflash from THT's rom because I couldn't connect at all unless I hard reset. Makes no sense cause my husband can sync and he had the identical same rom.
Hi!
I'm having trouble using my tytn II as a modem in windows vista. I had no problems in windows xp but since i installed windows vista and use internet sharing application this is what happens:
I get connected and a new networkadapter (NDIS) is detected
I recieve a local ip-adress of 169.xxx...
This is making me crazy and i've searched the forum without beeing able to find anyone with the same problem...what am i doing wrong??
Any help will be greatly appreciated!
Thank you!
I understand, you use it with USB cable, may be using it with Bluetooth will be better, because in this case Windows will recognize it as a modem.
Please provide some more information about how did you make the configuration.
Did you make it as it was described in the user guide?
Hi!
I did make the configuration exactly as the manual describes it and my device is syncing correctly and everything. It even installs as a network driver when i use the internet sharing application. But it just wont give me an ip-address...
I've had this issue for over a month now and it feels like vista is blocking the service or something, but i just cant figure it out...
PLEASE advise!
I have the same Problem as you !
As a matter of fact, I have an ip but vista says that I'm connected to local network but not to the Internet.
But at the same time I have an illimited data plan that runs perfectly when using Pocket ie...
Still searching for a solution...
But i'm sure it comes from vista...
megaman
No problems!
Hi guys.
Ive used this feature with vista with no problems at all..
Just turned internet sharing on and it connected to the network connection then vista aked me what kind of network it was (Home, Work Place etc) and hey presto it worked.
Mine is a T-Mobile Vario iii btw.
Never really had a problem either though it's much too slow compared to a "real" USB-3G/HDSPA-modem. (I max out at 1.2-1.8 mbit/s but when I use my dedicated modem I easilly reach 4 mbit/s)
megaman said:
I have the same Problem as you !
As a matter of fact, I have an ip but vista says that I'm connected to local network but not to the Internet.
But at the same time I have an illimited data plan that runs perfectly when using Pocket ie...
Still searching for a solution...
But i'm sure it comes from vista...
megaman
Click to expand...
Click to collapse
Yeah this is killing me! I get the same as you, i get a IP-address but its a local one 169.xxx.xxx.xxx and vista says its a local ip-address...
I've started looking for services that may be stopped and such in Vista, but i still cant get it to work
I also can't get it to work, so if my WiFi goes out and i need internet, i just reboot to XP... Obviously not a solution, it's very annoying. I'd love to figure this out. I think my friend said he got it working, i should get details from him!
-Taylor
Guys, this is not the solution, BUT, until someone finds it, this is a awesome way to get around the problem! Just install the application, start it and tap connect. Now on your computer you'll find a new adhoc network using wifi, connect to it and your ready to go!
http://www.jongma.org/WMWifiRouter/
Hi folks,
Just having a problem that's really winding me up... I really hope some kind soul can help...
OK, I have a laptop running WinXP Pro and ActiveSync 4.5
I have a Kaiser (T-Mob VIII) running the shipped ROM...
Everything has been working fine for months, ActiveSync (never used it to Sync items with the PC, purely to explore the device and move files around etc), and Internet Sharing worked without any problems...
Anyway, I'm just visiting my folks and my Dad's been having a nightmare with his Nav Cam 7700 Sat Nav unit. Basically support for the device has folded and we've lost faith. I did some reading and it turns out you can 'tweak' it to run TomTom...
So, I connected his Sat Nav to my laptop (it runs CE Core 5.0), and used Mobile Registry Editor to adjust its 'init' values to kick-up explorer rather than the (terrible) preloaded Sat-Nav software... Everything went fine, we've now got his gadget working fine and all the problems he had with the terrible software it ran previously are solved
The only issue I'm having now though, is that my laptop completely refuses to connect to my Kaiser... The system-tray icon turns green and 'spins around' for a while when I connect it, but after a while it throws up the 'troubleshooting' tool because it can't connect. Needless to say, that doesn't help solve the problem.
I've un-installed and re-installed ActiveSync, checked all the old Application Data folders, DLLs and INFs are gone (removing some by hand where necessary), and I've been through the registry on my laptop to make sure none of ActiveSync stays behind...
The problem is exactly the same
I've even tried connecting my work phone to the laptop - that's a Hermes running a HTC WM6 ROM - it behaves exactly the same as the Kaiser...
Hard-Reset of the Kaiser and changing its device name didn't help either.
...The [email protected] sat nav unit still connects fine though! £%^$)%!!!!!!!!
I'd be sooooooooo grateful for any thoughts people have, as this is driving me nuts now - I really don't want to have to reformat and reinstall my laptop just to get AS working...
Thanks,
Rob.
Bro, I'm having a big problem with the mini USB plug.... when you plug the cable to your device, does it shake or it's very stable?
The plug seems pretty stable...
I guess it can be 'wiggled' a little, but nothing that gives me cause for concern - it seems as 'tight' as the connection on the Hermes I have with me (and two more that are back home)...
I was wondering about cabling/connections for a while, but I tried Internet Sharing too, that still works fine - so there's a solid-enough connection between the laptop and the PDA - it's just that ActiveSync isn't playing ball :s
Thanks,
Rob.
Try this...on you phone go to start...settings...connections..usb to pc and uncheck enable advanced network functionality. See if it works then.
jhernand1102 - you have got to be on the shortlist for the position of 'The Font of All Knowledge'... Based on your reply I should probably now be asking 'Why are we here?' or 'What's it all about?'
That worked (in case you hadn't guessed by the paragraph above! )...
I'm confused though...
1) Why did it work with the option enabled before, but not now...
2) What have I actually turned-off? The geek in me will be a little upset thinking about 'Advanced' functionaility that was previously enabled but now isn't...
Thanks
Rob.
FactionOne said:
jhernand1102 - you have got to be on the shortlist for the position of 'The Font of All Knowledge'... Based on your reply I should probably now be asking 'Why are we here?' or 'What's it all about?'
That worked (in case you hadn't guessed by the paragraph above! )...
I'm confused though...
1) Why did it work with the option enabled before, but not now...
2) What have I actually turned-off? The geek in me will be a little upset thinking about 'Advanced' functionaility that was previously enabled but now isn't...
Thanks
Rob.
Click to expand...
Click to collapse
You are not missing anything by disabling the advanced network functionality. As a matter of fact, the USB2PC application that runs on the Diamond and Touch Pro actually advises you onscreen that you should disable it if you have connection issues.
Yeah, when I went in there I saw it was the same on my Kaiser (duh!!! - silly me!)
The thing is though, I couldn't understand why it worked with it set before, but all of a sudden didn't want to.
That caused me to do some more reading...
So with that option enabled, Sync is handled via an RNDIS gateway, with it disabled, it's basic serial-over-USB. So, for basic things, disabled is fine; but for more unusual network communication configs involved in your ActiveSync, it might be better to have the advanced network functionality enabled...
I could probably manage with the serial-over-USB method, but I would a) like to know I can use RNDIS gateway should the need present itself, and b) as a bit of a geek, I'm not happy with something all of a sudden refusing to work - especially if it's an aspect of 'functionality' to some degree...
So thinking about RNDIS not working, I started messing about with Windows, and my Firewall...
I'd already set ActiveSync (all three main executables) as trusted apps in my Firewall config, and made sure that the ports required by it were open to everything inside my internet gateway.
I made sure that Windows Firewall (lol) was disabled...
I tried with my firewall 'disabled' - running, but allowing all traffic... Still no Sync...
So, god only knows why, I just quit my Firewall app, removing it from memory...
ActiveSync worked!
I re-started my Firewall, and made NO CHANGES WHATSOEVER to its configuration...
ActiveSync still worked!
...So, it's all working again - and in effect, nothing's changed.
I'd still really love to know how connecting the Win CE Core 5.0 device knocked out sync for anything which wanted to use RNDIS... I guess I might never find out... If anyone has any good theories, I'd be interested to hear, but I am prepared to cut my losses now it's working - Never look a gift horse in the mouth!
Thanks again for all your input folks,
Rob.
Hi guys, I mingled with my phone last night and installed this android build i saw on neopeek, it said it has 3d drivers and camera working so i thought idd give it a shot. I installed it and it worked pretty fast , then i wanted to download an app and started wifi.
It took longer than usual to activate so i went to settings (i activated it from the power control widget 1st) to check out whats going on. And wifi it was saying activating .. error. I tried a few times when i said to myself , oh well, good build , but wifi aint working.
I returned to windows mobile and now i cant activate it anymore not even in windows mobile. I tried everything, soft reset, hard reset, installed a stock rom, nothing works
can anyone help me ? is it broken hardware ? should i use the heat gan on the wifi chip ? what should i do ? thanks
this is what the guy says to do
tampitzel wrote:
hi, i installed your rom, replaced the kernel for the camera to work, and i tried logging into wifi, it said error. i returned to windows mobile and now the wifi doesnt work in windows mobile either. is there something i can do ? thx
i remember that in early version it happens. I thinks the solution was to reset our device until windows recognize wifi.
i tried everything, soft reset, hard reset, installed a different rom with new radios, nuthin` worked. I think the wifi is broken hardware
Also When im in windows mobile and i go to device information , i can see the bluetooth mac address, i cant see wifi anywhere in the hardware tab
Sorry for editing once again , just wanted to say i tryed MTTY format + ROM installation, and its the same, i guess its hardware broken and i need a heatgun, will post updates, if anyone cares
200+ views and no answer. Thats pretty sad, i guess im posting so i can bump it in front, maybe someone sees it and can help somehow.
you don't see wifi MAC address under hardware..
I had same problem, changed bottom buttons(contains wifi chip as well) and now working
I changed them because they had pretty bad scratches.
you can get those pretty cheap on ebay.
if reassembing, make sure you connect screen and buttons ribbon cable(they don't snap in)
solved
Okay first of all i would like to thank the person who posted an answer , it really helped.
I didnt even buy new buttons, i just disconnected the phone from all the connectors (display, buttons, etc.), and reconnected. It was really hard reconnecting the display but i did it in the end. Now wifi works once again !
One happy camper here !
If you guys have the same problem , and have enough patience to disassemble and reassemble , this is your answer !
Mods, you can rename this one as solved