Flashed another device´s ROM into Rhodium and bricked :( - Touch Pro2, Tilt 2 Windows Mobile ROM Development

Hi,
A friend has a CDMA Sprint Rhodium, and he tried to install with a Raphael ROM into Rhodium and since that device won´t turn on.
When connected to PC turns the led in red and it says "Qualcomm CDMA MSM driver needed" but nothing happens...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Is there anything I can do to help him? or device can´t be repared?
Any advice is welcome
Thanks in advance,

i think you should contact jockie

Thanks for the advice, I´ll contact him.

Can he get the phone into the bootloader ?
Not sure that driver message is connected with the problem though, when you turn on a GSM Rhodium connected to the computer it normally wants a CDMA driver.

well, if the device is making a connection with the computer, then it's turning on. it may not be displaying anything, but at least you know it's still working. so, remove any SD card you may have and if you have a SIM card, remove it (i believe you said CDMA, but you are in the GSM forum, so...) Now, this will take some dexterity. first, remove the battery. Now, while depressing the volume down key slip the battery into the phone and quickly press and release the power key while still holding down the volume down key. either instantly or within a few seconds you should get the tri color screen. once this occurs, try hooking the phone back into your PC and running a custom ROM that is for the proper make and carrier style

guys, hes not a newbie, and knows about bootloader mode
this case isnt regular, so i advised a man who can really help with it, as i got help in similar situation

The "Qualcomm CDMA" driver installation comes up on your PC even on GSM phones.

try to download this driver from internet, it's for windows xp
then inter the bootloader and flash the original rom

hehe, the problem is not in drivers, drivers isnt a problem, you can use practically any qualcomm device driver (e.g. motorola Q)
the htc usb interface cant be found here (htc usb sync)

Can you get into bootloader screen or wont that even come up? If it does best thing would be to put a stock rom on an Sd card and flash from there.

I guess this is the problem that Nykoon had few days ago.
See, the phone has Raphael's bootloader. The CPU aren't the same (MSM7200A vs 7201A), nor the rest of the board. The bootloader can't make USB sync, so it somehow probably goes into some failsafe bootloader... but without proper files from HTC it can't be recovered.
Maybe jockyw can do something about it, but all at all - JTAG will work fine.
For all - that device doesn't go even to bootloader probably. If it went into bootloader, you would see at least HTC USB Sync (or microsoft usb sync). We tried with Nykoon on ICQ many things, but no way of flashing anything on it.

Thanks a lot guys, with your guidance we were able to bring it alive!!!
Thanks a lot to all
-----------
Vote, check my sig!

Hi, can you help me please, i have 1 with the same problem, please help me to flash the device, thanks in advanced

orb3000 said:
Thanks a lot guys, with your guidance we were able to bring it alive!!!
Thanks a lot to all
-----------
Vote, check my sig!
Click to expand...
Click to collapse
Please post the solution.
May help others in the future.

this has happen twice to me, fixed both times
all you got to do is put it in bootloader Mode (hold down vol down and push power button) then go to att, or tmobile .com and download the original factory ROM, (with original .exe) load it and the phone works perfect, then you can load any custom rom you want after that
for some reason, over time, with all the flashing, files just don't transfer correctly, one file here, one file there, and it takes the original factory ROM built by IN-HOUSE team at Phone Carrier. and not the made in the basement
Roms we have on here, I have flashed all of them, and love Energy, but for
some reason, Agent47 Valkarie roms, usually after some use, make my phone
Brick and lock and all kind of stuff, but reload ATT factory exe rom and Re-Flash
with NRG and thats it,
let me know how it works out

Related

Deleted My HTC Wizard Radio Rom

I was tryin to update the radio rom on my MDA and i i was usin the RUU and i guess i did somethin wrong cause now thers a X where the active sync is and a exclamation point where my reception bar is, also wen i go to about device i dont see the radio rom where the others ones are listed. So i downloaded the universal radio gsm exe but it doesnt recogize my device even thought it pluged in my microsoft active sync does recognize it either. and now its runs extremly slow, could someone give me some insite to wat i have done wrong and how i can fix it,
Thanks klawdlan
PS i am runin the orginal firm that came wit my mda US-Tmobile
The radio for the Universal will not work in the Wizard.
so what should i do to fix my prob
Download a Radio Rom (as an example you could try the Cingular 2.25 Radio Rom) for the Wizard on the XDA FTP
my pc is nto recognize it after i deleted the radio firm, even wen i plug in the wall charger thers no indication thats its chargin.
Can you get in bootloader mode by pressing the camera button (and hold it) and then doing a soft-reset?
If you get the tri-color screen, THEN try to update the Radio Rom, if that doesn't work, then you are in deep **** I guess!
yea i can get to that screen
Then go into that screen and flash the Radio Rom!
The Radio Rom is located here: ftp://xda:[email protected]/Wizard/Radio_Roms/wizard_radio version-2.25.zip
Good luck.
how will i get the rom to the pda if it wont even recognize it in microsoft synce, i cant even browse the device wen i go to my computer?
Listen carefully!!
- Connect your device via the cable to your PC.
- Get your device in the bootloader (tricolor-screen) mode.
- Unzip the zip file with the Radio Rom
- Go into to folder you unzipped it in
- Doubleclick the .exe file and follow instructions on your screen!
Good luck!
p.s. You flash Roms from your PC to your device, you dont flash Roms "on the device itself".
p.s.2 Maybe it will be smart to do a hard-reset afterwards (because your device is very very slow, look at my post in this topic on how to do a hard-reset http://forum.xda-developers.com/viewtopic.php?t=56145&highlight= ).
i did everythin u said word for word wen ruu was runin this came up
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and i continued and in about device it doesnt show a radio rom
Just continue!!
Just press Next or Continue until it starts flashing or gives an error!
i did and i still get no radio rom in the end
Dont pay attention whats on your screen.
You can end up with 2 things:
1) You get an error and the update failed.
2) The flashing begins and you will get a message when it's done!
Molski
i get the message that its done and that i flashed, but in im in wm5 and i go to systems about device i still dont see a radio rom
Then grab a Full Rom from here: ftp://xda:[email protected]/Wizard/Roms
And flash the Full Rom the same way I decribed for flashing only your Radio Rom.
Good luck pal !
p.s. When you turn on your device, don't you see a Radio Rom (GSM version number in your top-left corner?
alright ima try it now, thanks
PRAISE BE UNTO molski FOR HE HAS HELPED ME FIX MY FONE, thanks man i got a hang of this update thing now, learned mucho mucho i would make a new thread in ur honor if it were proper forum edicate
It's never wrong to thank someone (especially me in a new thread haha)
I'm glad your phone is working again that and you learned how to do things like flashing your Wizard!
And now you can play around with it....you know what to do if something goes wrong
Regards,
Molski.

Can't flash radio, no GSM error, need help

Hello
I downloaded the new radio this morning
when tried to flash it to my Trinity I've got "connection timeout" error
now when I start it there is an error "no GSM"
and it freeze in the HTC screen
I searched the forum for all day, flashed alot of radios, hard-spls and so on but didn't manage to flash a working radio
Please give me some instructions or a link the the right thread
I have original HTC rom with SPL-1.30 Olipro
Thanks
exactly the same problem here, need help guys, anyone?
checkout this site for more info that may help you. i had to downgrade/reflash to SPL 1.20 Olipro, flash the new Radio and then reflash to SPL 1.30 Olipro.
I managed to fix it
download this file
http://forum.xda-developers.com/attachment.php?attachmentid=43539&d= 1184192788
in ActiveSync go to connection settings
uncheck the allow USB connections
restart the device in bootloader mode and connect it to PC
run the .BAT file
the device will boot in bootloader SPL 1.2
now you can flash ROM\RADIO
good luck
yes, if you're having trouble flashing radio, please use Hard-SPL 1.20 olipro
wow guys thank you, you saved me 600 eur, i've read around the forum that htc wouldn't have given me warranty rights with the modified rom installed on the trinity, actually the radio update process is around 40% (while it wasn't going further 7% before). So i assume everything is working correctly.
After the radio i'll be installing the UDK4 WM6 again and everything should work correctly now (so to prevent any other less experienced guy to have similar problem, if he wants to upgrade both main rom and radio rom, i suggest is better to upgrade the radio rom before, don't you agree?).
thank you guys, i'll let you know my feedback as soon my trinity is up & running again
thanks you all guys, everything works correctly, i didn't know that we could reinstall any rom with a "bad flash / brick" problem without sending it in htc assistence.
The problem was regarding only the Radio ROM, that was completely missing after the bad upgrade. Didn't have to reinstallo the Main rom (UDK4 In my case).
Thank you all again, i wasn't able to sleep thinking about this thank you can have a good night now
Regards,
Michele!
racerx_ said:
yes, if you're having trouble flashing radio, please use Hard-SPL 1.20 olipro
Click to expand...
Click to collapse
Where to get this? I only find V1.30. Thanks!
download it here .. look at post #85
Thank you very much! I didn't find it!
Bye, Peter
I have a siilar problem. I had flashed radio 1.46 completily the progress were up to 100 %, but when I soft reset the device say "No GSM", only if I put off batery during 10/15 seconds it is all right,
Whats is hapenng????
Any solution????
Thanks
I have the same problem too...
Dispositive info no said nothing about radio version.
I've load Olipro but if I try flash it with a radio version it dont pass of 0%
What can I do?
Best regards
Same 0% problem
Ayasystems, I have the same problem of ROM update not going over 0%... how did you fix it?
Thanks in advance
nirgur said:
I managed to fix it
download this file
http://forum.xda-developers.com/attachment.php?attachmentid=43539&d= 1184192788
in ActiveSync go to connection settings
uncheck the allow USB connections
restart the device in bootloader mode and connect it to PC
run the .BAT file
the device will boot in bootloader SPL 1.2
now you can flash ROM\RADIO
good luck
Click to expand...
Click to collapse
How long does it takes to complete this part of the program?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It seems if he stucks with this part by me. How can I check if it is still working? What do I have to do now? Retry it again? Or..?
I tried many of the solutions here to fix my "no GSM" error message. I even sent it to Pocket PC techs. They "remolded" the chip.?? I don't know what that means or even if I said it right. I recommend their service. BUT, that still didn't solve the problem. I finally bent the sim card brackets down to hold the sim card a little tighter, and it worked. Haven't had any problems since. I spent months and about 100 US to fix this and thank God it works now.
I really think it was a combination of what Pocket PC techs did, plus bending the brackets down. I don't think any of the software fixes helped at all.
Hope this helps out. Blessings all!

It won't start anymore! Help!

I just have this phone, the SPV M700 for a few days. With the Orane brand on it. I also have the SPV M500 (Magician) with big-storage rom on it. So I thought I would know how to do this, but apparently I dont?
I want to update and want to remove the CID and Sim-lock. But first things first, so I want to run Hard-SPL.
So I have downloaded the Hard-SPL file and run it. When I do this, everything goes like it should till the tri-color screen on my pda. After that I get this error in windows (XP):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
En I got this screen on my PDA:
So something goes wrong. I have this also when I try to flash to a Orange rom (I have an Dutch rom on the PDA but I also get this message when try to flash it to an English ROM from Orange. And every other rom) When I put out the battery for 3 sec or just simply do a soft-reset everything seems to work like it did before the I tried flash.
Can someone plz help me, I don't know what to do!
I again got the error with Hard-SPL but someone said to me he had that to and he just went to the next step. So I did to. This time it seemed to work because progress balk was going until 22%. Then it stopped. I did a repair as it was described in the flashing program and now it doesn't start anymore. It goes until this screen and not further:
I can do a hard reset but it still stucks on the same screen. WHAT NOW??
I first get this screen, and just before the text (M 05 / B 05 / D 1.23) disappears, the text NO GSM comes in the blue-area above the D 1.23
This is there for I think half a second and then I have the screen as in my post above.
I have read that I can try 3 things.
NeilM said:
You can try 2 other things!
Download the Radio ROM again- you may have had a downlaod glitch in the 1st one. V1.38 is the best one to try.
Download and install the offical HTC WM5 ROM- this should be a full ROM including Radio, so sometimes completes more effectively. If you are brave, you can them retry the WM6 flash!
Click to expand...
Click to collapse
and
zohaer21 said:
since bricking a hermes i stopped taking chances doing rom upgrades via usb..
the method that is most reliable ad safe is... via SD card
extract RUU_signed file from the upgrade pack (use winrar) and then copy it to the root of a blank sd (mini or micro etc) and rename to TRINIMG.nbh ..enter bootloader and follow the steps.. its fast and most reliable
Click to expand...
Click to collapse
I think that trying the first thing is the best? Retrying to install a new Radio Rom. He suggest to use version V1.38. Is this still the best rom to try it with? Or can I better take a newer/older one?
And where can I find these Radio Roms?
An update how far I am now, I have read about Splxploit
nirgur said:
I managed to fix it
download this file
http://forum.xda-developers.com/attachment.php?attachmentid=43539&d= 1184192788
in ActiveSync go to connection settings
uncheck the allow USB connections
restart the device in bootloader mode and connect it to PC
run the .BAT file
the device will boot in bootloader SPL 1.2
now you can flash ROM\RADIO
good luck
Click to expand...
Click to collapse
How long does it takes to complete this part of the program?
It seems if he stucks with this part by me. How can I check if it is still working? What do I have to do now? Retry it again? Or..?
Click to expand...
Click to collapse
I have done that. I didn't came further than the screenshot above. So I started unbrick.dat again and this time it doesn't go further than this:
Even after another retry to start it, it doesn't go further. It doesn't reach the same status as this picture:
(picture is from http://trinityguides.info/index.php?option=content&task=view&id=22 )
What do I have to do now? I'm stucked again..
Markos said:
An update how far I am now, I have read about Splxploit
I have done that. I didn't came further than the screenshot above. So I started unbrick.dat again and this time it doesn't go further than this:
Even after another retry to start it, it doesn't go further. It doesn't reach the same status as this picture:
(picture is from http://trinityguides.info/index.php?option=content&task=view&id=22 )
What do I have to do now? I'm stucked again..
Click to expand...
Click to collapse
where come you from ?
please write a PM in dutch to me
I will help you
YESS! I have done it, I don't know how but it works again I don't have a clue what I have done. I have done so many things and everytime I get a different respons with the same actions.. But it works!
But now, I want to remove the sim-lock. I have followed the actions in the topic. When I do the automatic way (run AUTO_Unlock_v1.bat) I get this error:
And if I do it this way:
pof said:
If you don't want to install automatically, or for some reason the process doesn't work for you, here are the manual instructions:
Transfer SSPL/SSPL-TRIN.exe to your phone and run it
Tri-color screen will appear
Disable activesync (file -> connection settings -> uncheck "allow USB connections")
Connect your phone to your computer using the USB lead.
Run RUU/ROMUpgradeUtility.exe
Follow the flashing process (Check the "I understand..." and "I completed..." boxes and update!)
Allow your phone to reboot.
Transfer TRIN_Unlock_v1.exe program to your phone and run it
Click the Unlock Button, select unlock option. Select if you want SIM/CID unlock.
Click "Unlock!" and wait until process finishes.
When done, turn off your phone for 10 seconds and reboot after that.
Click to expand...
Click to collapse
I'll get the same Error, ERROR [302]
What goes wrong?? Everything goes like it should, but when I click on Update I get the Error [302]
*dutch:
ik kom uit het gezellige brabant Weet je toevallig ook hoe ik de sim-lock kan verwijderen?
Topic can be closed. I have superCID, no SimLock anymore and a cooked WM6 on it!
*Markos loves xda-dev

Accidentally restored WM6.0 files after flashing 6.1 Tilt locked up. HELP PLZ!

UPDATE...REMOVED BATTERY FOR A WHILE AND UN/RE INSTALLED ACTIVE SYNC AND DEVICE WAS RECOGNIZED AGAIN! Was then able to re-flash 6.1////hope this helps someone else.
Thanks for the help!
Ok, I have read for 2 days, trying to find a fix for this, and even posted in familiar threads with my issue for help. This is my first thread. Someone PLEASE help me!
I flashed my Tilt from HTC e-club the other day. I read to use the PIM back up...so I did. The flash was a success! Everything worked fine. I popped in SD and opened PIM but could not find backup log. I still had everything backed on Sprite so I just restored with it. BIG BIG BIG mistake! It showed all the files reloading and then did its auto reset. Once phone reset I got that irritating Att screen then the shrilling 3G screen...THEN IT GOES BLACK! If its not black its filled with black and white bars going down the screen b-w-b-w-b-w-b-w-b-w. Active-sync no longer recognizes my device, I cant get it to hard reset with soft keys and stylus. I dont have any info I cant live without on the phone. I have saved all of my data,cabs, pics, etc. on my SD.
I tried the black screen fix...no good, I tried to re flash from bootloader/multi color screen, I plug in USB and my PC dings like I have connected but nothing. Device goes from serial to USB in multi color screen but PC sees nothing. Hopefully someone has an idea that doesnt require another device purchase.
Thanks help would be greatly appreciated.
I didn flash hardSPL can I still flash original 6.0 from SD?
Did you by chance try a HARD reset ? ( BOTH SOFTKEYS and the soft reset on the bottom )
Just so you are SURE which buttons are correct....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ALSO,
Have you changed your SPL?
If so, copy the nbh to the root of your SD card and rename it to KAISIMG.nbh ( Case Sensitive just as I have it here )
After doing this go into bootloader screen ( camera button and soft reset ) and it can reinstall a rom from SD
One more thing,
Im not sure if sprite gives you the ability, but go into its settings and make sure to NOT copy the crucial windows registry entries as this WILL mess up your operating system if you changed from 5.0 to 6.0 or 6.1
A Hard Reset and then re-restore from Sprite, but do NOT restore any Windows OS Files / Registry settings, etc.
Thanks
Dave
changing SPL.
pyraxiate said:
Did you by chance try a HARD reset ? ( BOTH SOFTKEYS and the soft reset on the bottom )
Just so you are SURE which buttons are correct....
ALSO,
Have you changed your SPL?
If so, copy the nbh to the root of your SD card and rename it to KAISIMG.nbh ( Case Sensitive just as I have it here )
After doing this go into bootloader screen ( camera button and soft reset ) and it can reinstall a rom from SD
One more thing,
Im not sure if sprite gives you the ability, but go into its settings and make sure to NOT copy the crucial windows registry entries as this WILL mess up your operating system if you changed from 5.0 to 6.0 or 6.1
Click to expand...
Click to collapse
Yes I did the hard reset correctly. It just continues to soft boot.
I believe what you said above is what happened.
When I backed up w/ sprite it copied original OS files from 6.0 on top of new 6.1.
I have not changed SPL unless it was done through the steps on the HTC site as I was loading 6.1. I don't think it does, but I may b wrong.
Can I still flash from SD?
this happened to me. Just reset your device while holding the camera button. you should see a tri colored screen. run the offical 6.1 update. ignore the instructions just run it and tell it to install.
PC/Active-sync doent see my device
DemoShadow said:
this happened to me. Just reset your device while holding the camera button. you should see a tri colored screen. run the offical 6.1 update. ignore the instructions just run it and tell it to install.
Click to expand...
Click to collapse
Could your phone still sync?

Issues properly installing ADB/Fastboot on Windows 7 64-Bit

Hi, all,
my radio refuses to upgrade on my G1 so im desperately trying to get adb and fastboot working to i can use hard spl to flash the newest radio (since im on the oldest one right now).
Im on a Windows 7 64-Bit HP Laptop and after using the usb drivers that came with the latest SDK, I managed to get adb working for literally 1 minute before it automatically shut off and the system stopped recognizing it and throwing out a Code 10: Device cannot start error. I downloaded USBDeview and uninstalled the usb drivers then I went through the registry and deleted all 'vid_0bb4&pid_0c02' keys values and folders...except one that keeps throwing this error for me:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Even when i set permissions to delete it, i still get that error.
Even though i deleted all the values but that one, i managed to install it successfully once i used DroidExplorer, and i managed to get it working for literally 1 minute before the driver stops sensing the phone. Any suggestions?
Uninstalling the driver in device manager and installing it from device manager always worked for me. But I havn't used Windows for the past month+ so there could have been an update or something that breaks ADB.
ive tried that a thousand times =/
no i dont think they made an update that prevents it.. ive been trying off and on to install adb for a few months now but now that i flashed hard spl in hopes of fixing my stupid radio, ive been aggressively trying for the past 2 weeks lol
Anyone have any suggestions? I was thinking of formatting the whole hard drive on the computer but that's extremely painstaking and a little extreme...anyone have any ideas?
speedysilwady said:
Anyone have any suggestions? I was thinking of formatting the whole hard drive on the computer but that's extremely painstaking and a little extreme...anyone have any ideas?
Click to expand...
Click to collapse
You shouldn't format for something as small as installing a single driver, the headache that comes with setting up countless progs or accs and what not isn't worth it, at least for me. i had dual-booted vista instead since it worked with the DL'd driver. I haven't tried in 7 though haven't looked for the driver yet.
Yeah you're right formatting would be a huge pain, that's why I'm wondering if anyone can help me remove that registry key cuz I think that's what's been screwing up my install.. I can't dual boot an earlier OS because I don't have the disc for vista or xp. =/
You get this error when you plug in your phone?
And how are you trying to flash your radio? When you're in recovery, you can't flash the require update.zip? Maybe give some other information, like what ROM are you on, what recovery?
tehseano said:
You get this error when you plug in your phone?
And how are you trying to flash your radio? When you're in recovery, you can't flash the require update.zip? Maybe give some other information, like what ROM are you on, what recovery?
Click to expand...
Click to collapse
I am currently on Super D 1.9.2 (modified to fit on Any SPL)
Amon_RA Recovery 1.6.2
Yes Ive had this problem forever, i used to be stuck on the .11 radio, it refused to update to 26i or the latest radio whenever I used amon_RA or cyanogen's recovery image, whether i used button shortcuts to flash or if i manually selected the radio update with the trackball. It would flash with no error message but everytime i held power and camera itd be the .11 radio, and the baseband displayed the same thing...then I was advised to make a goldcard and use DREAIMG.nbh to downgrade to .29 and reroot...which i did, and after trying again to upgrade the radio it wont even go up to .11 and above now.. even after flashing Hard SPL. So now Im trying to get ADB set up so I can fastboot a radio update. I have no idea why it wont work through recovery.
bump anyone?
Try a system restore? I can't really help you, all I have is vista
Can anyone give me the link to a guide to get fastboot drivers and fastboot.exe working on 64-bit windows 7? XDA search is down at the moment and I'm searching like crazy on google and not finding the results. I want to flash a new recovery on my Tab 10.1, thanks!
OneStepAhead said:
Can anyone give me the link to a guide to get fastboot drivers and fastboot.exe working on 64-bit windows 7? XDA search is down at the moment and I'm searching like crazy on google and not finding the results. I want to flash a new recovery on my Tab 10.1, thanks!
Click to expand...
Click to collapse
Here you go sir:http://www.youtube.com/watch?v=Bg-cGTZE2XI&feature=related

Categories

Resources