I posted this in the forum for the ROM but want to widen the audience. I am installing a ROM using RUU and keep getting communications errors. I have a partnership setup and it finds the phone perfectly. It detects the version and then reboots the phone fine. Both the PC and the Phone come up with the progress bar and sit at 0% for a minute and then I get a communications error and it fails. I tried this on an XP machine with activesync and on a vista machine with no luck. Anyone else ever had a similar issue with some ideas on what I can try?
Thanks,
Chris
tell me you have hard spl.
I don't actually but I did not brick my phone. I can yank the batter for a minute and then put it back in and it boots right back up. Could that utility make the communications issue resolve itself?
hardpl
Ok, I found this and it seems the process for installing this is the same as installing a new ROM and the communications issue happens here too. There has to be something simple I am missing. Anyone? Please!!
Hi!
Ive got a big problem with my Qtek 9090..I wanted to flash my OS to Wm6 but during the instalation the device lost connectivity..I dont know how and since than i cannot start it again...i cannot get to the bootloader mode
what should I do???
Did you try holding record-power +reset?
I had some of these issues before, disconnecting, battery down, ... but always managed to get in 'usb-mode' after which you can retry the flash update...
If it doesn't work, give us some more info what happens, what you tried and what did what... we'll (try to) help you out
don't panic, there's always a solution
I have the same problem, i try to updated to Helmi WM6 in my desktop Windows Vista, but my BA never come for the USB V2.07
YES !!! same here.... at 37% my connection lost and i can't TURN IT BACK ON AGAIN .... How come ? What should I do ?
I already browse the whole upgrading things and I (believe) never make any mistake when do it.
plz help me .......
SOLVED ! see my post HERE
I've had this problem. We've had to flash about 250+ devices and four of them were disconnected before 100% download.
we've not been able to do anything with these devices except just write them off and not use them.
If anyone knows how we will be able to get them working again it would be greatly appreciated.
thanks
Hey everyone. I'm tearing my hair out trying to get this sorted but I just don't know what to do!
So, when I got my X1 as everyone on here should do, was flash my X1 with the HardSPL and some custom roms, this was a few months back. Then, shock! Horror! My case went and broke, (cracked near the volume button build W44) so I sent it back to SE for repair. I sent it back reset back to defaults but left the hardspl on there.
SE sent me a brand new phone (I think... This one says under the battery build w50, but the battery says w32..) I received it today. I thought it would be my old one repaired but SE had other ideas. Booted up and have Image Version: 1.03.931.10 and HardSPL 72.000 I think I said that correctly...
Now since sending it for repair and receiving it back, their seems to be quite a few wm6.5 roms floating about, and obviously I can't use the stock software as that wouldn't be right!
Now I have tried flashing the hardspl to the phone through my Vista PC and all it keeps giving me is connection errors. I thought maybe it was already flashed so I tried flashing just a rom, and that just made the phone get stuck on loading (flash by memory card). I thought it might be Vista, so I tried doing it on my other PC (XP) and I get the same issue. This bloody thing won't flash!
I have had "Connection Problems" - "Update Errors" with different numbers. The current one being Error [260] CONNECTION.
Now I have been searching around through the hardspl thread and other places trying to find out what I need to do or how I can fix it, but everything I try doesn't make a difference. I did read some other people with recently repaired phones having the same problem and perhaps SE have put a new spl thingy-ma-jiggy on there. (Please forgive the technical jargon, I have no idea what im on about.) I have also tried the ticking/unticking advanced network functionality, but that hasn't made a difference either.
So by the end of typing this, I have little hair left. Let's hope you can all help, before I have none left!
I would appreciate ANY help! Really.
Just wanted to add, I was at first getting the phone to a loading bar when flashing, but it would stay at 0% then flag up an error on the PC. Now after the tri-colour bars, the phone just sticks on Loading...
Well just to update. I have been trying to sort this since posting. I flashed the rom to an old UK generic one, as I read in another topic people had to do that before HardSPL. Done that, and tried flashing the hardspl. Same thing, just getting connection errors.
I tried going into bootloader and running the hardspl from there. It works and the phone gets to 10% and then gives an UPDATE ERROR. The phone is now bricked, and I have to reflash the original wm rom to get it back.
Though the Tricolour screen now shows 0.52.Olinex
Any ideas?
Shameless bump for help.
very stupid situation.
i have the same situation in puncto of flashing.
i get my phone three month ago.
after hardspl i .... sorry, no hardspl ... the phone says at 0% bla bla bla
i solve the problem by consulting one night absolutly stressing again and again and again .... google ... xda ... google
than 3 thinks at one time was the solution:
0. need activesync - connect !!!!
1. SDA_ApplicationUnlock.exe for desktop pc
2. enterbootloader.exe for pocketpc (please, the right version, it exist for eten too, but we need the xpediaversion ..)
3. changing registry-entries
how to:
activesync-connect, than copy "enterbootloader.exe" to pocketpc. it must be root, not sd-card. use a pocketpc-registry-program to change these values :
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies\0000101b = 1
if not exist than add the key.
now, start desktop-program, follow instruction EXCEPT reboot.
start "enterbootloader.exe" on pocketpc. now, you can install hardspl and the device is flashable for ever.
thats works on me, hope it could help you too.
Thanks for the reply. Not had time to try it till this morning. Ok so, after spending about an hour trying to find the correct enterbootloader.exe I finally realized, that the hardspl package includes it. *Duh!* So that was time wasted.
I changes the registry values as you said with Resco registry editor, and follower the unlock then enterbootloader.exe Start HardSPL package. Starts to install. Gets to 10% then I get
ERROR [262] : UPDATE ERROR
The rom update utility has encountered communication errors during the update process.
So im open to suggestions if anyone has any. I just can't understand why it's not working. It's not a problem with my computer or cables. I flashed the phone before I sent it for repair and I have tried doing it on two computers one with XP 32bit and one with Vista 64bit.
hmm. would u like to install a custom rom, or a stock rom?
msg me, and i hope, i can halp u.
I want to have the hardspl on there so I can flash custom roms.
If it's a case of the software/firmware/hardspl whatever you call it, has been updated by SE. How would one go about getting it flashed? Would we have to wait for an update HardSPL to be released?
U read this thread?
My first hardspl was from this thread. New X1 will come tomorrow back from SE (vibration was defect +++ some more problems with case), and i will try it again with this thread.
hope, this will help u mate.
Yeah, I have been through that thread with a fine toothcombe trying everything suggested to see if I can make it work.
When you get yours back, if you have to do anything out of the ordinary to get it to flash or can't do it. Please come and let me know in this thread. If they have updated yours like mine, and yours won't flash, at least I won't be the only one!
k, i will msg u tomorrow around 2pm.
Cheers.
In the meantime. Does anyone have any other suggestions I could try?
Bump, for some help.
now i know, what is exatcly your problem.... <--- SAME Problem
i hope, i will find a solution and msg u then. if u´ll got a solution for this prob, msg me too plz.
Solution found in this Thread!
Download this and unzip it to your device. ++ run it. It will start your X1 in Bootloader menu and say "0.52.OliNex".
Then start hardspl while X1 is in Bootloadermenu....
FINISH =)
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
vwrmic said:
Thanks for the reply matey. Glad you got yours sorted. Just tried what you said and I get 0% then it switches to ERROR [262] : UPDATE ERROR.
Click to expand...
Click to collapse
hmmm... it works fine on my new x1. are u sure, that u start the ssplmanual on your x1 and not on your computer?
Yea, im not sure what the problem was with it. Thankfully I have it done and dusted today! Because I flashed it earlier to an older official version, and you said you got it working. I presumed you had - had yours flashed to the newest version due to it being off for repair. So I reflashed the official update and fully updated it. Then tried hardspl which didn't work. Tried with the advanced USB thing off, tried again with how you said you did it above, and Viola!
Hip hip hoorah! Thanks for the help. Can finally use me bleedin phone now!
no problem mate hf with your x1
hello,
i see smilies and yea's ...
for me to understanding (for next time or other users):
1. complete official update (if exists)
2. flashing (hardspl) without "advanced usb"
thats all?
cool.
Hi I have an AT&T Tilt2. Ive been trying to flash it for about a month now. I was able to flash my pure without a single issue. I have loaded SSPL ran it on my phone then started manual flash. It Jumps from 0% to 100% then shows Error [266] Flash Write and says IU434 in the bottom corner of HardSPl. I have searched and searched and cannot figure out what im doing wrong. Any help would be greatly appreciated. If this has already been brought up and solved please point me to it. Thanks in Advance.
Why not just let the pros unlock your Tilt2?
Im not wanting to unlock it i just want to flash a different rom to it.
Problem solved i finally got it.
Hello, im having issues with my HD7. I just recieved a replacement phone from t-mobile and it was really buggy and freezing so i decided to try to reflash the stock firmware. I have tried both versions that are available for the HD7 for T-Mobile and the phone goes through the process in ruu but hangs at 11%. Doesnt go any further and eventually times out with an error 262. I have also tried to flash with rspl but no luck as well. I can not wipe the phone or do anything on it as it is stuck in bootloader. Can anyone please help me to install the stock firmware back to my HD7......any help would be greatly appreciated
Did you hook it up with zune first to make sue all the drivers were installed prorperly?
Try these from microsoft
http://support.microsoft.com/kb/2484484#StuckInDownloadMode
Good luck
tfn said:
Did you hook it up with zune first to make sue all the drivers were installed prorperly?
Try these from microsoft
http://support.microsoft.com/kb/2484484#StuckInDownloadMode
Good luck
Click to expand...
Click to collapse
Thanks for your quick reply tfn, but unfortunately i do have the current drivers installed on my pc. The really strange thing i just found out is that it will let me flash a non stock rom, like dft's mango but will not allow me to go past 11% on the stock rom. I dont know, im on tmobile's prepaid and this phone has a warranty, i just hate that i cant get this new "refurb" to work that i just got in from t-mobile. It frustrates me so much, cuz i loved wp7 on my HD2 but im having nothing but bad luck with these HD7's :'(
Anyone please......