HTC Wizard 9100 - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Hi Guys! I Have a really Big Problem, My Wizard, Stuck at boot loader, i turn on the phone, his boots about 1 minute, and goes to boot loader, and i cannot sinchronize it, with AS. I try to flash him, bud flasher can't detect the phone. ;/ Any help?

Related

HELP. tried upgrading.. stuck at 98%

hey.. ive upgrade to new roms before.. however i tried going from the cingular 2.25 rom to summiters aku 2.3.. and it froze at 98% and was unable to finsh.. now I jsut tried downgrading and it froze again at 98%.. it won't complete anytthing.. help. please.
It's normal for it to seem to freeze at 98%, but it really will complete if you just wait a few minutes. No worries... just be patient.
If Stuck
hey if your phone is doesn't go through with the rom upgrade and doesn't push through and when you reboot you get stuck on the boot screen.
Put your phone into USB programming mode by holding the camera button down and doing a soft reset with the stylus. Then you will be able to load any rom you choose.
With regards to your frozen at 98 just give it time i would say don't unplug
same problem, still stuck
2nd time trying to load "Cingular_Custom_AKU2.3_Combo_Installer_V1.exe" ROM but still stuck at 98%...on the computer it says 100% and finishes but the phone is still stuck at 98%..tried to do a soft reset, but stuck at bootloader screen..
Help pleaseee!
Thanks!

Help Me ---- Bootloader Screen Stuck

When i switch on my qtek 9100 it is stuck with boot loader. It says loading windows and stays that way.
can anyone please help me fix this problem.
how can i reset my device.
i tried to put a new rom image. but i cannot as the active sync connection is not on due to being stuck with bootloader.
CAN any one plese help me solve this issue.
THANK YOU
Aamer
aamer said:
When i switch on my qtek 9100 it is stuck with boot loader. It says loading windows and stays that way.
can anyone please help me fix this problem.
r
Click to expand...
Click to collapse
Ok, you aren't stuck at the bootloader, you are stuck at the 3rd splash screen. To fix this you need to get to the bootloader.
Just follow this guide and you should be good.
http://forum.xda-developers.com/showthread.php?t=298613
You want to flash an official rom onto your phone at this point. Once you get it working then you can try doing a custom rom (or whatever you want).
Hi!
You can also try it out this procedure if you are still feeling stuck!
http://forum.xda-developers.com/showthread.php?t=294107
Good luck!

Flashing ROM and SPL

Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])

help help help !!!!!! bad flash/unlocker

iv had the elegance rom on my p3600 running perfect so try'd to unlock the phone to half way through it disconected from usb and rebooted but will only go as far as start up i love this phone and want it back the way it was any help please
havent u installed hard spl first?
if not...that could be a problem!
if u did just press the camera+power+soft reset buttons to enter the bootloader and install everithing again...see if that works!
(if i am wrong just correct it)
do have boot loder or spl-9.99.cp?????
whatever i put on just gets stuck on boot loader screen ???

Stuck in Bootloader screen

Hello all,
as the title says, one of my touch diamond's is stuck in bootloader screen.
I didnt do anything in between it working and not working, it was on my desk, put it there working, got it 5mins later, and it was in bootloader screen (tricolor screen).
What i've already done to try and fix it:
flash it with the original HTC rom, flash completes succesfully, phone reboots to tricolor screen, so no solution there.
install mtty and format the phone, this completes, reboot the phone, again goes to the bootloader.
reflash the phone with original rom after cleaning it with mtty, flash again completes succesfully but when it reboots after flashing it just goes to bootloader again.
Tried to flash a Hardspl: stuck at 0% and stays there. so that doesnt work.
BUT! when in mtty i give the "boot" command, it DOES start to boot WM. but then again, when i turn the phone of, and on again, or it reboots because of first start after flash, it goes to bootloader again. The VOLDOWN button is NOT stuck, cause when it boots i can use the vol buttons perfectly fine.
Anyone got an suggestion in how to unbrick it? i have a second, perfectly working diamond here too, if that helps in any way.
Some more info ive just seen in mtty, when i told it to boot, it said ONE BAD BLOCK IN CE, remove block ---- to ---- (dont know the exact numbers anymore)
hi..i had something like that...
just download this.
"RUU_Signed_1_93OliNex_HSPL_UnsignedEdition"
it's only 1.7MB and it's will make it work.. atleast it did the job for me...
Hi,
My T mobile touch diamond stuck in bootloader screen? Any experties to help me please.
Thanks in advance.

Categories

Resources