Database Develop

Romupdate dowsn't see my USB connection

I put my pda in bootloader mode. Serial v1.00 is what i see. I plug the USB cable in it and what i see is USB v1.00. I start romupdate.exe, but it cannot see the usb connection.
What am i doing wrong? I tried it on 2 pc's, both are not working.
Any help appreciated.

Nevermind, i forgot to kill the activesync process.

i hv dopod838 wwe , installed & run the lookiwz02a ( U & C ),
but when running romupdate, with activesync usb off, still romupdate won't recognize the usb. i also tried mtty with same result, usb not recognize.

PLEASE HELP!!

I tried using the Siemens upgrade for my SX66, which made it display Serial on the top and v2.07 on the bottom
I followed the steps reccomended for when such a thing takes place (ie doing a flash reset on the phone) but now the screen remains black and doesn't even display Serial and v2.07
When plugged into my computer, absolutely nothing happens and the computer does not recognize it.
I eventually got the screen to display USB, ran the update again but after about 15 minutes I got an error screen on the PC that read:
Error 201: Get Device Data Error
Can not get device data. Please make sure device are connected to PC and execute this update utility again
Please help!

(The problem really?)finished

hello
The problem really????
try on I want to UPGRADE to WM6
enter into screen​
Written by stuck in grey scren, "Serial" or "USB"
and in the under-screen : V2.07
and No, never go................
( I am stuck in grey scren, "Serial" or "USB" (when the device is placed in the cradle) )
all this in siemens sx66
What is the solution???
I am waiting​

Was the solution to the problem
Thank you for all

i think i can decipher enough words to know that your problem is
being stuck in the Bootloader Mode. "Serial/USB" Screen
place your BA in the cradle.
run MaUpgradeUT_NoID.exe

TRIN100 stuck at operator logo

I tried unlocking it with 'HTC_Trinity_SIM_CID_Unlock_v1' and ran the ROMUpdateUtility.exe. But the process stopped at 7%, after that phone booted up and got stuck at the windows mobile green screen. After a few soft/hard resets phone boots upto operator logo but no further.
The tri color screen shows IPL-0.50 and SPL-1.07.0000
This is about all the info I have about this device.
Please help me revive this device. What do I do next?
Thanks

i have similar problem, but im stuck at screen alignment

Any way to revive this device, please

Please help, I promise another donation and a third star

I get the exact same problem.
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000

have you try this one ? http://forum.xda-developers.com/attachment.php?attachmentid=43539&d=1184192788

IT WORKS...
Yes I tested it last night on my notebook but I did not know why, it did not work.
(Permission denied cannot conect to \\.\\WCEUSBSH001)
And I found that I forgot to DISABLE USB CONNECTION in Activ Sync.
Thank you.

For those In the same case as me, just after Windows Exploit, do not soft reset because the Olipro bootlaoder will disappear. Flash directly with your RUU.
Thanks XDA.

help please stuck on tri color screen

hi this morning i i tried to upgrade the rom on my diamond however it is now not booting past the tri color screen and it wont connect to my pc i am a newbie so prob put the wrong rom on (idiot i know) anyway the top section of screen is red and in top right corner it says ruunbh below that i have diam100 64m
spl-1.93.olinex
microp-diam (led) v11
green section psoc-diam stage_pvt v0x32
upgrade rom code error please try again
blue section nothing
white section
serial
i can not change the serial to usb and therefor cannot connect to wmdc it just same unrecognized usd device ive tried hard reset but still the same can any one help me please or should i just chuck it in bin thanks

not an expert but few things that could be made out from your comments :
-it could be a bad flash of ROM.
try this maybe it could be of some help - while on this screen, put the usb cable back on the phone and it will change from Serial to USB. try flashing the same ROM or maybe download another one and see if it works.
Best of Luck!

thanks i tried this all ready but the serial just stays there it wont change to usb

hi,
try this
download mtty on ur pc, connect ur mobile with ur pc via usb and uncheck the option of active sync. After doing this type commands in mtty (do not copypaste) :
password BsaD5SeoA (press enter & wait for sometime)
ruurun 0 (press enter)
please dont type (press enter & wait for sometime), you have to press enter button after typing BsaD5SeoA and again after typing ruurun 0
then restart and it should boot then.

hi i cannot access the phone to uncheck active sync which com port do i use on mtty each time i connect the phone to pc it comes up the usb device has malfunctioned and is unrecongnised thanks

if you cant acheive a usb connection during bootloader, then ur fone is bricked mate.... contact htc and ask about a repair

tonyplym said:
hi i cannot access the phone to uncheck active sync which com port do i use on mtty each time i connect the phone to pc it comes up the usb device has malfunctioned and is unrecongnised thanks
Click to expand...
Click to collapse
You dont need to connect to active sync as it wont even connect as ur phone is not able to start completely. You just open the active sync software and in connections just uncheck the option of sync . For COM just try all the availible COMS.
Best of luck

thanks i have just taken it out from the drawer and switched it on and serial has changed to usb so i have now reinstalled the orignal rom and im back in business thanks for all of your help now to find a suitable rom what do you recomend thanks