Related
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
Hey,
Just looking for some advice where I should go for a cheap solution on how to fix my phone. Basically, everything still works great! Apart from the big crack, the screen doesn't seem to have been damaged (eg. All the pixels look fine, touch still works, only glass/plastic panel is cracked)
I'm actually really impressed by how it took such a hard hit and the device works fine, the screen didn't even smash! Basically it nudged in between my car seat where you close the door, didn't realise it fell out my pocket and closed the door (you could imagine it would be a hard hit) and the phone lives.
If I just needed the glass replaced, can it be done DIY? Or should I not bother and give it to a service centre? I got it from 3 but I know they'll probably overcharge me for something like this..
Any suggestions welcome, thanks!
if the damage is only to the exterior screen then you may want to consider getting this:
http://www.mobilefun.co.uk/product/17042.htm
be carful! the screen from my firlfreidns diamond is broken too and I had ordered one of those touchscreens... but the screen which comes has no "window" for the frontcamera and after disassembling the phone I saw that it is NOT POSSIBLE to remove the touchscreenglas from the frame.
Replacement LCD & Digitiser
I recently replaced an lcd and digitiser on a HTC Touch Diamond. I bought the complete screen (lcd & digitiser) as one pre-assembled unit from a guy on Ebay (£34.99). Fits straight into the front of the unit frame. I don't think you can remove just the digitiser because it is stuck onto the LCD, and the LCD itself is very fragile. Disassembly is fairly straight forward if you've got the right tools.
Thanks for all your help guys! I've just been bogged down with work so havn't been able to get back here for awhile.
I've taken some time to look into the webiste and others, decided to just order it off ebay in the end anyways. However, taking note from the previous 2 posts, would I be wasting my time ordering just the digitiser itself? I would assume that's what HerrVorragend also meant by "that it is NOT POSSIBLE to remove the touchscreenglas from the frame."
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Double posted, sorry.
badtzmaru56 said:
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Click to expand...
Click to collapse
If you google for HTC Diamond Service Manual, that will help greatly with assembly and disassembly - there are also a couple of videos on Youtube. From my experience the most tricky part is re-connecting the two flex connectors when you re-install the main board. I use the back of a pair of tweezers to slide underneath the connector carefully. If you are nervous about doing it and happy to cover postage costs, I can replace the LCD for you - PM me for details and I'll see what i can do.
Andy
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Hi all!
I bought a HTC One M7 with a cracked screen dirt cheap from a friend and am hoping to repair it myself and I've had a look around the q&a forums but anyone that references to genuine or "OG" HTC parts doesn't specify where you can actually order them from, I'd be looking for both speakers, lcd screen, digitizer and front speaker covers but am pretty unsure of which parts are actually legitimate on the internet.
Any help guys?
TIA
Beans
bbeanss said:
Hi all!
I bought a HTC One M7 with a cracked screen dirt cheap from a friend and am hoping to repair it myself and I've had a look around the q&a forums but anyone that references to genuine or "OG" HTC parts doesn't specify where you can actually order them from, I'd be looking for both speakers, lcd screen, digitizer and front speaker covers but am pretty unsure of which parts are actually legitimate on the internet.
Any help guys?
TIA
Beans
Click to expand...
Click to collapse
Screen repair here, fairly cheap and apparently 100% genuine, saves you a lot of hassle, i.e, breaking it apart and re-sealing it, plus the possibility of damaging other parts, also ring them and ask if they can replace the other parts for you.
http://www.ebay.co.uk/itm/Repair-Re...410?pt=LH_DefaultDomain_3&hash=item19f93950c2
if not then the speakers are here, cheap as chips, you could always ask the LCD company, if you send the speakers with the phone, if they wouldn't mind changing them at the same time, it would take them 2 mins whilst they have it apart.
http://www.ebay.co.uk/sch/i.html?_f...m7+speakers&_nkw=htc+one+m7+speakers&_sacat=0
for the covers, depends on colour, but heres an idea:
http://www.ebay.co.uk/itm/New-Top-F...sPouches&var=460531438066&hash=item2594a951a1
All for less than £100, cant really beat that for the whole front end of the phone.
If you are going to replace the screen might I suggest you order an entire front housing with digitizer and screen and back housing. You will destroy your phones body when you open it. Order those parts and follow the complete breakdown and reassembly videos on YouTube. They are all good.
Is it hard to change just back cover?
bosas200 said:
Is it hard to change just back cover?
Click to expand...
Click to collapse
Personally I wouldn't take the risk of opening it all up myself, inside is extremely fragile and the motherboard connections for instance is as easy to rip in half as a piece of cloth, I destroyed a HTC Desire HD whilst trying to change the LCD and Digitalizer and the back of that was screwed on, the HTC One series is 10 times harder to open up.
Check this out for an idea of what is involved: https://www.youtube.com/watch?v=jVUAr5hLiEE
Hi all,
I recently fell whilst holding my brand new N6 and cracked the screen pretty bad. The digitiser and LCD appear to work OK, so I'm taking the plunge and will try and replace the glass myself.
I've replaced the display module (glass, LCD and digitiser) for a number of family/friend's phones and feel comfortable about working with the small electronics. I've been reading and watching countless tutorials on the removal of the glass from the rest of the display assembly but and yet to find any information specifically about doing this on the N6. Specifically, I'm worried about how the speakers will affect the glass removal process.
If anyone has any N6 specific info, it would be most appreciated. I'm waiting for the replacement glass to arrive, I'll update this thread with how i get on!
Check out
https://www.ifixit.com/Device/Nexus_6
Sent from my Nexus 6 using Tapatalk
good luck, I have only managed to get anew screen on an iphone 4, failed miserably with my Nexus 7 2012, and I was clued up about what to do....
violentbydezign said:
Check out
https://www.ifixit.com/Device/Nexus_6
Click to expand...
Click to collapse
I've been through that. Will be useful to get me to the display module, but would have been nice if they showed what it looks like in more detail. I'll be sure to take lots of pictures when i do this and maybe a video.
mediaman123 said:
good luck, I have only managed to get anew screen on an iphone 4, failed miserably with my Nexus 7 2012, and I was clued up about what to do....
Click to expand...
Click to collapse
Did you try replacing just the glass or the whole display module? What went wrong? I'm also about to replace the display module on the N7 2012, the glass is cracked and half the digitiser doesn't work.
dixonl90 said:
Did you try replacing just the glass or the whole display module? What went wrong? I'm also about to replace the display module on the N7 2012, the glass is cracked and half the digitiser doesn't work.
Click to expand...
Click to collapse
with the iphone it was both the LCD and Digitizer I was replacing and they came together as one................same with the N7, both together, trying to install/remove these separately is suicide unless you have the right tools etc........
Have you bought the LCD/Digitizer toggether inside the silver bezel, I didn't, and I should have.........
basically there was a small cable on the back of the LCD/Digitizer that was present on the old damaged module, but not on the new one I had bought, I tried removing form the old and into the new, plugged in the normal power and screen cables, but then nothing, didn't work, my frustration also resulted in a small crack to the new screen.............
it possible but you need to have patience and the tools, which it sound like you do.......but its much easier already inside the silver bezel...........
the screen was glued into the bezel and removing this was murder, managed it, but had to pick out all the smashed glass bit by bit........
don't let me put you off though, you sound more competent than me........
mediaman123 said:
with the iphone it was both the LCD and Digitizer I was replacing and they came together as one................same with the N7, both together, trying to install/remove these separately is suicide unless you have the right tools etc........
Have you bought the LCD/Digitizer toggether inside the silver bezel, I didn't, and I should have.........
basically there was a small cable on the back of the LCD/Digitizer that was present on the old damaged module, but not on the new one I had bought, I tried removing form the old and into the new, plugged in the normal power and screen cables, but then nothing, didn't work, my frustration also resulted in a small crack to the new screen.............
it possible but you need to have patience and the tools, which it sound like you do.......but its much easier already inside the silver bezel...........
the screen was glued into the bezel and removing this was murder, managed it, but had to pick out all the smashed glass bit by bit........
don't let me put you off though, you sound more competent than me........
Click to expand...
Click to collapse
I haven't bought the replacement display module yet for the Nexus 7. Thanks for the info, think i'll try and get one with a bezel to be on the safe side.
its definitely the way to go as you will just be popping off the back cover, releasing the ribbon cables, removing some screws, peeling back some adhesive tape and that's you.........
and any dings to the bezel will dissapear too............
Removing the LCD ribbon cable on N6 is PITA I don't want to even think how to plug in the new one. The digitizer is easy since there is lock on it but the LCD just plugs in with lots of friction.
Any tips?
dixonl90 said:
Hi all,
I recently fell whilst holding my brand new N6 and cracked the screen pretty bad. The digitiser and LCD appear to work OK, so I'm taking the plunge and will try and replace the glass myself.
I've replaced the display module (glass, LCD and digitiser) for a number of family/friend's phones and feel comfortable about working with the small electronics. I've been reading and watching countless tutorials on the removal of the glass from the rest of the display assembly but and yet to find any information specifically about doing this on the N6. Specifically, I'm worried about how the speakers will affect the glass removal process.
If anyone has any N6 specific info, it would be most appreciated. I'm waiting for the replacement glass to arrive, I'll update this thread with how i get on!
Click to expand...
Click to collapse
hi, how you repair cracked screen on your n6?
can you replace glass screen only or screen complete(digitizer/lcd)?
pichigui said:
hi, how you repair cracked screen on your n6?
can you replace glass screen only or screen complete(digitizer/lcd)?
Click to expand...
Click to collapse
Unless you have the right equipment and lots of time buy the whole assembly.
You can watch videos on youtube how complicated is to separate the glass from LCD
£122 repair cost in UK.
Update
I'm experiencing the same problem. I've replaced the digitizers/screens on all versions of the iPhone and also on the Samsung Galaxy S4. I successfully replaced only the glass on some Samsung devices too. I'm wondering if I'll be able to do this with the Nexus 6 if I just buy the $10 replacement glass.
Thanks. Hope to hear your results soon.
EDIT: I've scoured YouTube in search of videos showing how to replace the GLASS ONLY, but I can only find videos showing how to replace the entire digitizer. So I'm desperate for any information on this. Haha.
cguarinus said:
I'm experiencing the same problem. I've replaced the digitizers/screens on all versions of the iPhone and also on the Samsung Galaxy S4. I successfully replaced only the glass on some Samsung devices too. I'm wondering if I'll be able to do this with the Nexus 6 if I just buy the $10 replacement glass.
Thanks. Hope to hear your results soon.
EDIT: I've scoured YouTube in search of videos showing how to replace the GLASS ONLY, but I can only find videos showing how to replace the entire digitizer. So I'm desperate for any information on this. Haha.
Click to expand...
Click to collapse
I was reading ifixit's how to guide. They state that the digitizer is fused to the glass. Possibly that's why everyone stops at this step.....
dixonl90 said:
Hi all,
I recently fell whilst holding my brand new N6 and cracked the screen pretty bad. The digitiser and LCD appear to work OK, so I'm taking the plunge and will try and replace the glass myself.
I've replaced the display module (glass, LCD and digitiser) for a number of family/friend's phones and feel comfortable about working with the small electronics. I've been reading and watching countless tutorials on the removal of the glass from the rest of the display assembly but and yet to find any information specifically about doing this on the N6. Specifically, I'm worried about how the speakers will affect the glass removal process.
If anyone has any N6 specific info, it would be most appreciated. I'm waiting for the replacement glass to arrive, I'll update this thread with how i get on!
Click to expand...
Click to collapse
What course of action did you end up taking with this problem?
robdevil said:
£122 repair cost in UK.
Click to expand...
Click to collapse
Can I ask where this is from? I've cracked the glass, screen works fine.
yes the glass repair is possible i am uploading photos of the process i did. i do work for a cell phone repair company and this has been a very common repair. Nexus 6 glass only repair with the use of OCA (optical clear adhesive) and bonded together with an ridge to ridge lamintator and and mini autoclave.
It turns out Motorola Official repair was £128 plus the postage to send them the phone in the first place.
I am unfortunately in the same boat. I sustained probably 15 scratches that my fingernail could get stuck on them all. My phone scraped along an artificial hardwood floor when a dog stepped on it facedown and slid. So I bought some cerium oxide in an attempt to sand down and buff away the scratches. I was not successful, and it looks like I added some more scratches. I'm going to put up with them until I get more, then replace the screen & digitizer probably while also adding a screen protector. I hate the feel of screen protectors though
tmotech88 said:
yes the glass repair is possible i am uploading photos of the process i did. i do work for a cell phone repair company and this has been a very common repair. Nexus 6 glass only repair with the use of OCA (optical clear adhesive) and bonded together with an ridge to ridge lamintator and and mini autoclave.
Click to expand...
Click to collapse
Impressive. What's your process for separating the cracked glass from the digitizer?
Although I'm sure the OP was asking for a way that doesn't require thousands of dollars worth of specialized equipment.
Has the OP given up on this project? I cracked my glass the other day however the digitizer still works just fine. I wanted to know if there was a do it yourself way to change the crystal without having to purchase a digitizer/crystal combo?
Thanks