Database Develop

HTC P3600 don't want to flash!

Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!

no ideas guys?

so no one can help me with an idea???

What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.

jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600

Do a hard reset and flash an OFFICIAL ROM from SD-card

Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.

thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?

If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.

nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out

No network after new ROM :(

I just flashed my Diamond with the: RUU_Diamond_HTC_NOR_2.03.409.1_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship.exe
I'm an norwegian that's in the US studying, so they only gave me the norwegian version. Anyways, everything worked fine until flash, but now my phone refuses to register on the network (AT&T)!
Took the sim-card back to the at&t nokia phone, worked the first time...
I really wants to use my Diamond instead of the crappy nokia, but it would be a shame to downgrade to 1.93 (which worked just fine...).
Someone, please have a solution for me?

simply install a new radio....try 1.00.25.07 that seems to be the only quadband radio..
(you have to flash an hspl before)

It's stuck on 0% and won't continue... Tried several roms :-/

no service?????
is there a soution to this no network problem
THERE IS A CROSS IN THE RECEPTION BAR AND WHEN YOU DIAL OUT IT SAYS "OPERATION FAILED"
any replies appreciated

Quite bad if the official RUU more or less bricks the device, at least turns into just a little computer

It screwed up my Diamond aswell The gprs is completely dead, been up all night trying to fix it, several hard resets etc, nothing helps... if it was a cooked rom I could tolerate it but official roms screwing up our phones this easily pisses me off.

Mine worked again, with the old 1.93 rom!!
What the hell did they do to 2.03? I suppose the radio rom is different at least... But I couldn't change to the old radio when I had 2.03, tried using the HardSpl...
Is it possible to flash _once_ with everything from 2.03, but the 1.00.25.05 radio (which is the one from 1.93)? Doing it sequentually doesn't work.

So what I did, as the final solution:
Flash with stock 2.03 rom
HardSPL
Flash with 1.05.25 radio
Works perfect!

Hmm i did the other way round with my o2 XDA Diamond (1.93 Stock)
1. Hard SPL
2. New Radio Rom (1.09.25.23)
3. 2.03 official Ger HTC Rom (without vendor lock)
works great as well

I've seen this issue a couple of times too. With 1.93 as well as with 2.03. Did not figure out what was the cause but never had a chance to bring the device back to life with some uninstallation or radio flash. I always went back to the SPB Backup from the night before it stopped working propperly.

Help!My Blackstone fails to accept a WM6.5 rom, as it used to the past!

Hi guys, I've been using the Energy roms quite often and I can say I did not fail to upgrade any of the updates. Today, my Blackstone "freezed" while I was surfing on the internet using opera, I took off the battery and I turned it on again but no success, so I decided to upgrade the rom (I was using the 25th Dec Rom). I followed the same procedure as always and when the installation ended the phone failed to boot. It reached at the stage where you are asked to enter the pin code, I typed it and then "nothing"! It kept frozen no matter what I was trying to do. I did several hard resets, I re-installed the latest rom (both versions) but nothing
Anyone knows how to fix this issue????
I need to say that in trying to fix this issue, I installed an old rom which was based on Windows 6.1 and the phone worked just fine, but the whole rom was so old, so I could not stay with that one. This means that the phone is not broken, right?
I also followed someone's here suggestion to go back to the original stock rom, hard reset and then install again the WM 6.5 roms. But again, this did not change anything. Is there a way to make the phone "accept" the WM 6.5 roms, as it used to accept them before???
Please help me cause I cannot live without this phone!!!
Thanks in advance for all those experts who are willing to share their suggestions with me!

gerakas23 said:
Hi guys, I've been using the Energy roms quite often and I can say I did not fail to upgrade any of the updates. Today, my Blackstone "freezed" while I was surfing on the internet using opera, I took off the battery and I turned it on again but no success, so I decided to upgrade the rom (I was using the 25th Dec Rom). I followed the same procedure as always and when the installation ended the phone failed to boot. It reached at the stage where you are asked to enter the pin code, I typed it and then "nothing"! It kept frozen no matter what I was trying to do. I did several hard resets, I re-installed the latest rom (both versions) but nothing
Anyone knows how to fix this issue????
I need to say that in trying to fix this issue, I installed an old rom which was based on Windows 6.1 and the phone worked just fine, but the whole rom was so old, so I could not stay with that one. This means that the phone is not broken, right?
I also followed someone's here suggestion to go back to the original stock rom, hard reset and then install again the WM 6.5 roms. But again, this did not change anything. Is there a way to make the phone "accept" the WM 6.5 roms, as it used to accept them before???
Please help me cause I cannot live without this phone!!!
Thanks in advance for all those experts who are willing to share their suggestions with me!
Click to expand...
Click to collapse
Have you tried various wm6.5 roms, possibly as bad download? Obviously I'm assuming you have either HSPL on device or you re-used USPL before flashing rom?
Did you flash back to original stock rom & SPL? i.e. rom and SPL which was on device when you bought it?

I had the same problem on the same rom, flashed stock rom then back to energy's. Been working fine ever since
Did you do a hard reset after installing energy rom too?

Fallen Spartan said:
Have you tried various wm6.5 roms, possibly as bad download? Obviously I'm assuming you have either HSPL on device or you re-used USPL before flashing rom?
Did you flash back to original stock rom & SPL? i.e. rom and SPL which was on device when you bought it?
Click to expand...
Click to collapse
Thank you very much for your response! I followed your suggestion to go back to the stock rom and spl and then flash cooked rom, although Energy roms still refused to install after all this procedure! I don't know why, because they have been working and installed just fine in the past. I suceed on flashing a Miris rom, not the latest one but an old one I had in my computer and fortunately it worked! So, according to the results of my experiment, my phone accepts WM6.5 roms, but not Energy roms! I will be waiting for an update of Energy roms to see if the new version will be accepted by my phone!!!
Thanks again for the assistance!

xmsnx said:
I had the same problem on the same rom, flashed stock rom then back to energy's. Been working fine ever since
Did you do a hard reset after installing energy rom too?
Click to expand...
Click to collapse
Thanks for the response, read what I wrote in my response to the other friend!

I got similar issues before, the phone just couldn't boot or hard reset itself after one or two days with many different 6.5 ROMs. Did an mtty task 29 then it looks good now for a week. If it still failed I would follow Fallen Spartan's suggestion to flash stock ROM+SPL.

gerakas23 said:
Thank you very much for your response! I followed your suggestion to go back to the stock rom and spl and then flash cooked rom, although Energy roms still refused to install after all this procedure! I don't know why, because they have been working and installed just fine in the past. I suceed on flashing a Miris rom, not the latest one but an old one I had in my computer and fortunately it worked! So, according to the results of my experiment, my phone accepts WM6.5 roms, but not Energy roms! I will be waiting for an update of Energy roms to see if the new version will be accepted by my phone!!!
Thanks again for the assistance!
Click to expand...
Click to collapse
hmmm, after returning to stock rom & SPL. What was your SPL in bootloader? Did you follow dummies guide afterwards and use USPL or HSPL before trying to flash NRG rom? Did you try a different rom? Whats your current SPL?

X1 and WinMobile 6.5 (Error 260 with HardSPL)

Hi,
I have some trouble on upgrading my Xperia X1 to Windows Mobile 6.5.
I tried to upgrade some months ago with the same error. Now I finally wanted to upgrade, but it doesnt work.
Ive read several instructions here and on a German board, but unfortunately without any success.
The only thing Ive noticed: HardSPL says, that I am running version 1.05.x on my phone and the new version would be 1.00.x, could this be the reason for the breakdown?
I am also looking for a current German Rom for the X1. The one I tried is from http://forum.xda-developers.com/showthread.php?t=526133
I'm not sure, if there are any newer versions, but it would be nice, if someone could help me.
Here is what I did:
- downloaded the german rom, mentioned above
- unpacked the kovsimg.nbh and put it onto my SD card
- started the HardSPL with the instruction
-> error 260 at 0% (after like 1 minute)
Please help me, I dont know, what I am doing wrong

PCServe said:
Hi,
I have some trouble on upgrading my Xperia X1 to Windows Mobile 6.5.
I tried to upgrade some months ago with the same error. Now I finally wanted to upgrade, but it doesnt work.
Ive read several instructions here and on a German board, but unfortunately without any success.
The only thing Ive noticed: HardSPL says, that I am running version 1.05.x on my phone and the new version would be 1.00.x, could this be the reason for the breakdown?
I am also looking for a current German Rom for the X1. The one I tried is from http://forum.xda-developers.com/showthread.php?t=526133
I'm not sure, if there are any newer versions, but it would be nice, if someone could help me.
Here is what I did:
- downloaded the german rom, mentioned above
- unpacked the kovsimg.nbh and put it onto my SD card
- started the HardSPL with the instruction
-> error 260 at 0% (after like 1 minute)
Please help me, I dont know, what I am doing wrong
Click to expand...
Click to collapse
not many details, but let's see
you successfully flashed h-spl (from olinex thread)? and when trying to flash custom rom you get the error 260? that right?
ensure to use customruu for flashing and not the ruu (hardspl.exe) from h-spl thread
if you use sd for storage of rom image, why not flash using sd-method in the first place?
a newer german rom is here

Problem with HTC Kaiser Tytn II - please help...

So my problem is - I put android on my htc tytn II and it worked (well kinda) but anyway I decided to switch back to Windows Mobile...
I installed 1.27.x.x radio , found a Windows Mobile 6 ROM and put (Like in the instructions ) Kaisimg.nbh(renamed from ruu_signed.nbh) and Kaisdiag.nbh to my SD card and then started flashing... It flashed smth,rebooted automatically and started booting android again...
Then I hold again camera button + power+ reset and since then when I put EVERY .nbh file on my sd card and try to flash it it STUCK on "Loading.." If I try to flash it with USB It stays at 0%.
The only exeption is if I try to flash from USB the rom that I tried to flash before from my sd card.. then it starts 0%..1% and reboot the phone...
P.S: Please help me...I think my device is not Broken but I dont know what should I do to fix it...

To flash back to WM from android put your kaiser into bootloader (multi colored screen) Then connect to usb. Download any WM build that is recent (I suggest Phoenix 3 for this, you can flash whatever you want later). After you download it open and run the included RUU that came with it and it will flash it on there.

hmm, I also had experienced the similar problem on my 1st time flashing back to WinMo.
When you are trying to flash via USB cable and the process stopped at 1% I guess there is also a message about "Invalid vender ID" right?
and if the text in your bootloader (tricolor screen) doesn't mention anything about hard such as "3.29.0000" (not "3.29.hard")
then
you've lost your hard SPL that's why you cant flash any .nbh to your phone.
I had managed to solve this problem by flashing stock WM rom for kaiser. The rom also has to be suitable for your phone, I mean if your kaiser is originally from France, then use French kaiser stock rom. Or if you are using AT&T Tilt use kaiser cingular stock rom.
you can find the list of shipped roms for kaiser here :
http://shipped-roms.com/shipped/Kaiser/
If you still have the "invalid vender ID" error message, try another stock ROM.

Thanks man you're my hero! I though I lost my phone.. anyway i bought new one - Nokia 2730 Classic but Ill sell the kaiser...
Thanks Anyway ... you're god!

Have the same problem...
Firstly, I'd like to point that the reason for the hard SPL getting overwritten by an original SPL is NOT HAVING UPDATED HARDSPL to a newer version that prevents accidental overwrite. This is instructed in the previous steps before actually installing Android. That was my mistake (I had HardSPL 1.0 OliPof), and now I can't flash no rom to my Kaiser (which thankfully works quite well in Android).
What happens (please correct me if I'm wrong) is that "KAISDIAG.NBH" is a modified, standalone hardSPL that will flash to the phone the SPL that comes with the "KAISIMG.NBH" you put in your SD card with "KAISDIAG.NBH"). In my case, I used the WinMo 6.1 spanish version 3.29.412.0, which, resulted in my phone being flashed with the original SPL 3.29.
Now, it seems many users have fixed this locating the correct stock rom and flashing it in their Kaisers. But to others, like myself, nothing seems to work. I believe that this is because we not only need a stock rom for our specific Kaiser model, but also it has to be compatible with the SPL that accidentally got installed in the phone. The problem is what if such rom doesn't even exists?
I'm really thankfull for all I learned by reading the forums (and from my mistakes ) and I know I'm in no position to make requests, but here goes what I think could help the users like myself to fix this, if posible:
1) Guide to identify what model of Kaiser we have (maybe it's already there, I just couldn't find it)
2) Complete list (or lists) of stock roms (There are some around, those are easy to find I think, but it doesn't hurt to share different sources)
3) Something like a JumpSPL for Android would be more than awesome...
Thanks in advance to everybody, sorry for my own stupidity . Any idea or help would be much appreciated,
Daniel

hmm, I'm not sure if it has to be compatible with the SPL.
In my case, I was flashing a very old WWE stock rom which has original SPL 1.56.
I also had been very desperate because any stock rom I found seems doesn't work and I even didn't know where originally my kaiser came from because I get it from my uncle. So I tried to flash any WWE stock rom I could found but nothing works. I read from Wikipedia that based on my phone model (Kais100), this model was only sold as AT&T tilt for US. But the problem is my phone is HTC branded, not AT&T tilt. Well, based on this information I also tried to flash some cingular stock rom but the result was just the same.
After contacting HTC Customer care, I know more info about my phone. They told me that based on my phone product ID, my kaiser was originally shipped for US, but unfortunately they can't provide me stock rom for my phone model. So I searched myself but this time I had better objective : to search HTC branded rom but for US.
finally, after days of search. I've found the rom that is suitable for my phone. Its called HTC WWE Brightpoint US which has original SPL 3.29 at the bottom of the list on the website I told you on my previous post.
few weeks ago I also accidentally overwrite my HardSPL again, but this time I did it with the stock ROM which has original SPL 3.29. But this problem also solved by flashing the stock ROM I've found before via USB cable.
So, I guess it has nothing to do with spl version.
Keep tying don't give up.

Update: Step 1 completed! YAY
Using the serial number and some obscure google searching, I came to the conclusion my KAIS130 is australian. Cheers, mate!
I verified this by being able to download stock roms from the australian HTC site with my Kaiser serial number. But at the moment of writing this, have downloaded two roms and no luck yet. 5 minutes remaining for the third one... Wish me luck...
Daniel.

Well... Now what?
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel

cuartetoraro said:
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
Click to expand...
Click to collapse
sorry to hear that..
well, extract the .nbh from exe and flash it via sd card is the method that made me overwrite my hard SPL in the first place.
hmm, did your phone comes with operator brand, such as three or something?

-Rif- said:
sorry to hear that..
hmm, did your phone comes with operator brand, such as three or something?
Click to expand...
Click to collapse
No, it's HTC unbranded. Now, something strange here: the label behind the battery has the serial number: HT830GB06075 and the P/N (guess it's part number) :99HCY194-00, but to the left of the camera, another label with the part number: 36H00563-00M and below says DATE:061107(TB02)/US.
I don't know if that's normal, but it caught my atention because my phone seems to have been dissasembled (little label over screw is teared). Maybe my Kaiser isn't Australian after all...