I was wondering if there was a way to make bluetooth so that it would select specific Bluetooth devices as a higher priority than others.
For example: I wear a bluetooth headset.
I would like for the Bluetooth headset to be used 90% of the time. However, when I am in my car, I'd want the car's bluetooth to be used. Right now I can't find a way to tell it to use my car's bluetooth, other than to manually go switch over.
Is there any tweaks that can be made so that it will choose to use the car bluetooth over the headset one when the car one is present, and to switch back to the headset once the car bluetooth is no longer in range?
Moved as not Android Development.
Related
Hi,
I am looking at getting a new car radio (JVC KD-AVX33) which has bluetooth and an option for using the bluetooth input for satellite navigation audio. (I assume that when it receives audio over the bluetooth it will switch the audio over from what ever I was listening to, to the sat nav voice and then back again when finished)
Is it possible with the bluetooth on these phones for pair the phone to the radio for the Sat Nav instructions, and also a headset for phone calls?
The A2DP and headset/handsfree profile can connect together and independently. It should work without any problem.
Surur
Hi;
Didn't find too many threads about the neatness of the Kaiser BT with certain devices. Though my main memory gets still eaten up like ther's no tomorrow I played a little bit today during lunch-time.
1.) External speaker/handsfree set:
I bought a blueant supertooth light since we have several phones in the family That's the most convenient way to have a mobile handsfree and no wires and literally NO installation.
Enable BT at the Kaiser, use BT-Audio (attached) and re-route device speaker output to the bluetooth handsfree speaker.
Voila, the TomTom Lady is talking to you load and clear. Eats up some battery but for that you have a car charger - NEAT!
Should work with popular motorola T305 and others as well.
2.) Car with AUX/iPod input:
Get an A2DP bluettooth kit (I have the i-tech clip R35) get a male/male 3.5 mm jack cable (preferable a little longer that you can use the mic), connect to the car. Not only that you can listen to the music stored on the kaiser through your car stereo ... call comes in, take call and listen through your speakersystem OR listen to regular radio or music, call comes in, press aux at your radio and ... talk.
NEAT - Thought I should share this!
doesn't seem to want to work for me. i get a " failed to enable BT audio" window when i try to use it
Could have a better user interface, I agree.
Do you use an external BT speaker/microphone or do you try to use AUX for your car stereo. If you use the car stereo NOTHING is required as long as you have an A2DP bluetooth set with external earphone jack.
With the car kit these are the steps that worked for me:
Enable BT in CommMgr?
Click BTAudioToggle
Click BTAudioOn
I put shortcuts in my menu one could even write a script or macro...
doesnt work for me
Post your config and what you did/do perhaps I can help
same thing as post #2,unzipped to SD, make shortcut,tried shortcut and direct file and both gave that error message
What speaker/headset do you have?
If it is a headset is it A2DP compatible?
jabra bt5020,dont think it's compatible
Hmmm
Bluetooth compliance: Bluetooth version 2.0 specifications
Supported Bluetooth profiles: Bluetooth headset and hands-free profiles
Try the following:
- Soft reset after you disabled bluetooth (to have a clear starting point)
- Enable bluetooth
- Check if it is connected
- Open settings
- Tap and HOLD on your headset
- Set as handsfree
- Set BTAudio ON (don't use the toggle)
- Open TomTom or whatever gives you some voice commands and check.
If it doesn't work ... well it doens't work with your headset ... sorry
If you REALLY want the function buy an itech or so for ~ 26 bucks
Quite a while ago I bought a Sony BT3600U car stero as it was bluetooth enabled so I could stream music from my Kaiser direct to the car speakers.
All was working well until I moved the car stereo to my new car.
Now although it's all paired up fine when I turn on the car stero it just links to the handsfree bluetooth but doesn't automatically go to wireless stereo.
Instead to get the wireless stereo to work I have to go into bluetooth settings click on xplode (which is the car stereo) and then choose set as wireless stereo.
I know from before that I managed to get it to automatically switch to wireless stereo when in range of the partnered car stereo but I can't for the life of me remember how I did it.
Does anyone have any clues?
Sounds to me like it's an issue with the stereo, not the Kaiser.
Perhaps try disabling the handsfree service (for that pair) on the Kaiser? I can't remember exactly if you disable certain services.
cotc2001 said:
Quite a while ago I bought a Sony BT3600U car stero as it was bluetooth enabled so I could stream music from my Kaiser direct to the car speakers.
All was working well until I moved the car stereo to my new car.
Now although it's all paired up fine when I turn on the car stero it just links to the handsfree bluetooth but doesn't automatically go to wireless stereo.
Instead to get the wireless stereo to work I have to go into bluetooth settings click on xplode (which is the car stereo) and then choose set as wireless stereo.
I know from before that I managed to get it to automatically switch to wireless stereo when in range of the partnered car stereo but I can't for the life of me remember how I did it.
Does anyone have any clues?
Click to expand...
Click to collapse
I have an XCarLink and I have the same behaviour which is a bit annoying. I did a bit of searching a while ago but never got anywhere. If there is an (easy) answer to this I would be interested.
Andy
No it's def not the stereo , i've got it working sort of using A2DP toggle but it's not automatic.
Installed A2DP toggle and linked it to the audio manager on the kaiser.
So I just click the play button on my home screen and it kicks in the wireless stereo and launches the audio manager at the same time and it all works.
It's just annoying as I know that before I moved the stereo from my Honda civic to my hyundai Coupe all I had to do was just start audio manager and the wireless stereo kicked in automatically.
I've seen this too; I have a Sony BT5000 (basically the same as the OP), and I've seen it with both Wizard & Kaiser devices.
A bit more testing - expected behaviour?
I went out in the car earlier and had to do the 'set as wireless stereo' trick to get the BT streaming working with the XCarLink. When I switched off the engine and the head unit powered off the headset icon disappeared from the phone (which is normal) indicating there was no connection. I then left the car but left the bluetooth enabled on the phone instead of switching it off as I normally do. When I returned and drove off the partnership was re-established and the headset icon re-appeared and I was able to stream music etc without doing the 'set as wireless stereo' trick.
I tested this a couple of times and the behaviour was the same - i.e. leave BT enabled on the phone but switch on/off the XCarLink (car kit) and the partnership re-establishes each time with Wireless Stereo working. Switch BT off and then back on on the phone and you have to manually select Wireless Stereo.
Is this the expected behaviour or is there a trick to getting this working seamlessly?
Andy
That didnt' work for me. I even did a hard reset on my phone to see if there was something I had installed causing it not to relink.
If I had any hair, i'd be pulling it out by now
It's so frustrating knowing that I had worked it out once before but when it comes to the crunch you can't remember for the life of you how you did it.
Well i've been searching for an answer and found this here
http://forum.xda-developers.com/showthread.php?p=1318542#post1320648
@ debully>
There is a very simple fix to enable the Pioneer to recognise and connect to your phone. You see the Pioneer is searching for a phone or a Smartphone, the Trinity identifies itself as a PPC and so the Pioneer ignores it.
The Class of Device or CoD must be changed so that the Trinity identifies itself as either a phone or Smartphone.
If you change the Dword Data value in.... HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Bluetooth\SY S\COD"
to 5374476 (decimal) and set bluetooth to discoverable in your Trin, you should find that it connects automatically.
It took me 8 months to find this out.
PS. I don't have the problem with not hearing the callers.
Click to expand...
Click to collapse
But it didn't work for me - on the plus side though I did find a really cool mortscript from the same guy which when I plug the kaiser into my car cradle/charger it recognises the car stereo (but doesn't set to "wireless stereo" and automatically loads up my media player
My search continues
EDIT: Ok found that once the initial partnership for wireless stereo is done, if I turn off the radio and turn it back on again, the partnership is lost as usual until I press channel 6 (pause) on my head unit and then it comes back on.
Hey guys got some questions concerning BT.
I have noticed that bluetooth doesnt always reconnect when it should. Or am i missing something here.
I have my phone paired with my stereo receiver in my car.
- I get in my car and turn on bluetooth. After about a minute my phone pairs with my car and everything is good. I can do calls, stream mp3's via BT and use Pandora as well. Now i stop at the gas station to get gas or whatever. I shut the car of there for breaking the bluetooth connection. Bluetooth is still enabled on my android. However when i start the car back up the phone will not connect to the bluetooth in the car unless i turn bluetooth off then on again.
I'm assuming this is do to some time out count in the BT stack? is there a way to edit something in order to make this auto connect? Any one with greater knowledge on the subject school me a little bit here?
Thanks!
I find the following app very good to quickly connect to multiple headsets/speakers
https://play.google.com/store/apps/details?id=com.sflab.bluetooth
ie. @ home i have a D200 creative speaker
instead of going into bluetooth settings.. just click the widget and its connected!
Cons: sometimes the widget does not respond.. but give it some time.
Updated Version of above:
One click - Connect 2 Specific Bluetooth device for A2DP and Phone app:
Bluetooth Pair
https://play.google.com/store/apps/details?id=com.gnssoftworks.bluetoothpair
found it very useful for swapping bluetooth headphones between devices WITHOUT turning off Bluetooth entirely or going into the settings menu.
Example Use Case:
I have one Stereo Bluetooth headset with mic (two profiles - phone and A2DP audio)
I have one Android Phone and one Android Tablet.
Phone Profile is always connected to the Android Phone, but the A2DP audio changes depending on which device you want to listen to music from.
Normally, if you want to listen to audio from the Tablet when your headset's A2DP profile is connected to the phone, you'd have to first go to the settings menu of the phone, and disconnect the A2DP, leaving Phone Profile connected. Then go to the settings menu on your tablet and connect the A2DP only.
Then you'd have to do the opposite if you want to listen to audio from the Phone again.
Takes a long time.
With Bluetooth Pair, you can specifically connect or disconnect to a specific device and specific profile (phone / a2dp) by widgets.
So you won't have to turn off the bluetooth completely on one device just to allow your headset to connect another device. Nor do you need to go into settings anymore.
1.) Just tap on the A2DP device specific widget on the phone to disconnect, the A2DP Profile from the phone
2.) go to the Tablet, and tap on the A2DP device specific widget to connect the A2DP profile of the headset to the Tablet
Two taps!